Alliance Laundry Systems HFNBCF Betriebsanleitung

Programming

www.alliancelaundry.com

MDC

Frontload Washer

Refer to Page 4 for Model Numbers

FLW1R

Part No. 801184R7

December 2012

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

801184 1

NOTE: The WARNING and IMPORTANT

instructions appearing in this manual are not meant

to cover all possible conditions and situations that

may occur. It must be understood that common

sense, caution, and carefulness are factors which

cannot be built into these washers. These factors

MUST BE supplied by the person(s) installing,

maintaining, or operating the washer.

Always contact the distributor, service agent, or the

manufacturer about any problems or conditions you do

not understand.

Failure to install, maintain, and/or operate

this machine according to the

manufacturer's instructions may result in

conditions which can produce bodily injury

and/or property damage.

W030

WARNING

means without the expressed written consent of the publisher.

2801184

Table of

Contents

Model Identification ........................................................................... 6

Preliminary Information.................................................................... 7

About the Control ................................................................................. 7

Glossary of Terms................................................................................. 7

Power Failure Recovery ....................................................................... 7

Card Reader Communications.............................................................. 7

MDC Identification............................................................................. 8

SELECT CYCLE Keypads................................................................... 8

START Keypad .................................................................................... 8

Display Identification ......................................................................... 9

Light Emitting Diodes (LEDs) ............................................................. 9

START LED .................................................................................... 9

WASH LED ..................................................................................... 9

RINSE LED ..................................................................................... 9

SPIN LED ........................................................................................ 9

DOOR LOCKED LED .................................................................... 9

Four 7-Segment Digits..................................................................... 9

Washer Operation .............................................................................. 10

Start Up................................................................................................. 10

Ready Mode.......................................................................................... 10

Closing the Washer Door...................................................................... 10

Signals................................................................................................... 10

MDC Special Features........................................................................ 11

Programming MDC .............................................................................. 11

Collecting Audit Information ............................................................... 11

Testing Machine and MDC Functions.................................................. 11

Rapid Advance Feature......................................................................... 11

Coin Drop ............................................................................................. 11

Start Pulse Operation ............................................................................ 11

Service Door and Coin Vault Openings ............................................... 11

Opening the Service Door .................................................................. 12

Stacked Washers and Dryers, Front Control Washers and

Coin Rear Control Washers................................................................ 12

Rear Control Washers Prepped for Card Reader.................................. 12

Entering the Manual Mode................................................................ 13

How to Enter the Manual Mode ........................................................... 13

Programming MDC............................................................................ 14

What Can Be Programmed? ................................................................. 14

Programmable Options Available......................................................... 14

1. Vend Price “AtS”......................................................................... 15

2. Coin #1 Amount “dEn1”.............................................................. 16

3. Coin #2 Amount “dEn2”.............................................................. 17

4. Start Pulse Value “PLSE”............................................................ 18

5. Cycle Stages “CyCL” .................................................................. 19

6. Configuration “CnFg”.................................................................. 20

Configuration Programming ............................................................ 21

7. Default Cycle “dCyC” ................................................................. 23

Collecting Audit Information ............................................................ 24

How to Enter Audit Feature.................................................................. 24

Entering the Audit Feature by Manual Mode .................................. 24

801184 3

Entering the Audit Feature with the Coin Vault Open .................... 24

How to Read Audit Data....................................................................... 24

How to Exit Audit Feature When Using Manual Mode ....................... 24

Testing Machine and MDC Functions.............................................. 25

How to Enter Testing Feature............................................................... 25

How to Start Tests ................................................................................ 25

How to Exit Testing Feature................................................................. 25

Diagnostic Test Descriptions................................................................ 25

Show Fill Time Test......................................................................... 25

Show Drain Time Test ..................................................................... 25

Production Test Cycle........................................................................... 26

To Enter Production Test Cycle....................................................... 26

To Exit Production Test Cycle......................................................... 26

Rapid Advance Feature...................................................................... 29

How to Enter Rapid Advance from Ready Mode................................. 29

How to Enter Rapid Advance During an Active Cycle........................ 29

How to Use Rapid Advance ................................................................. 29

How to Exit Rapid Advance Feature .................................................... 29

Default Washer Settings..................................................................... 30

Default Settings .................................................................................... 30

Default Cycle ........................................................................................ 30

Model Identification

Information in this manual is applicable to these washer

models:

HFNBCF

HFNBCR

HFNBDF

HFNBDR

HFNBEF

HFNBER

HFNBXF

HFNBXR

HFNBYF

HFNBYR

HFNCXF

HFNCXR

HTEBCF

HTEBDF

HTEBXF

HTEBYF

HTET17

HTET77

HTEX17

HTEX77

HTEY17

HTEY77

HTEZ17

HTGBCF

HTGBDF

HTGBYF

HTGT19

HTGT79

HTGX19

HTGX79

HTGY19

HTGY79

HTGZ19

HWFR61

HWFR71

HWFT61

HWFT63

HWFT71

HWFT73

HWFX61

HWFX71

HWFY61

HWFY63

HWFY71

HWFY73

HWFZ61

HWFZ63

HWRR61

HWRR71

HWRT61

HWRT71

HWRX61

HWRX71

HWRY61

HWRY71

HWRYE1

HWRZ61

HWRRE1

HWRTE1

HWRXE1

NTEBXF

NTGX77

NTGX79

NTGBXF

SFNBCF

SFNBCR

SFNBXF

SFNBXR

SFNBYF

SFNBYR

SFNCCF

SFNCCR

SFNCXR

SFNCYF

SFNCYR

STEBCF

STEBXF

STET17

STET77

STEX17

STEX77

STEY17

STEY77

STEZ17

STGBCF

STGBXF

STGBYF

STGT19

STGT79

STGX13

STGX19

STGX73

STGX79

STGY19

STGY79

STGZ19

SWFT61

SWFT63

SWFT71

SWFT73

SWFX61

SWFX63

SWFX71

SWFX73

SWFY61

SWFY63

SWFY71

SWFY73

SWFZ61

SWFZ63

SWRT61

SWRT71

SWRT73

SWRTE1

SWRX61

SWRX71

SWRY61

SWRY71

SWRZ61

801184

Preliminary Information

About the Control

MDC on the commercial washer is a programmable

control that lets the owner control machine features by

pressing sequences of SELECT CYCLE keypads.

MDC allows the owner to program cycle steps, set

vend prices, retrieve audit information and run

diagnostic tests. Washers shipped from the factory

have a default cycle (PERM PRESS/WARM) built in.

IMPORTANT: In the event of a power failure,

MDC will not have to be reprogrammed. It is

designed with a memory system that will remember

how it was programmed (for up to six years) until

the electrical power is restored.

IMPORTANT: It is extremely important that the

washer has a positive ground and that all

mechanical and electrical connections to MDC are

made before applying power to or operating the

washer.

Glossary of Terms

The following are a few terms and abbreviations to

learn. These are referred to throughout the manual:

Four-Digit Display – This term refers to the window

area of the control that displays values.

LED (Light Emitting Diode) – This term refers to the

lights on the keypads and status words of the control.

Power Failure Recovery

If power fails during an active cycle, the cycle status is

saved in memory. If door is locked when power is

restored, the washer will automatically resume the

cycle. If door is unlocked when power is restored, the

user must press the START keypad to resume the

cycle.

Card Reader Communications

Card Models Only

The control will communicate with a third party card

reader, available at extra cost from various card reader

manufacturers. Contact the card reader manufacturer

of your choice for availability and additional

information.

MDC Identification

SELECT CYCLE Keypads

SELECT CYCLE keypads are used to select the

specific washer cycle. These keypads include

NORMAL/HOT, NORMAL/WARM, PERM PRESS/

WARM, and DELICATES/COLD. The selection of

one of these keypads will light up the corresponding

LED. The default cycle is PERM PRESS/WARM. The

SELECT CYCLE keypads are not active after the first

fill cycle of the washer. Pressing the flashing START

keypad will confirm selection and cycle will begin

when vend is satisfied.

START Keypad

The START keypad is used to start the washer after the

full vend price has been satisfied.

Both the START keypad and the SELECT CYCLE

keypads are used in various combinations for

programming cycles, retrieving audit information,

running diagnostic tests, and other operations

described in Entering the Manual Mode.

Figure 1

FLW1R

1Four 7-Segment Digits

2Four-Digit Display

3LED Status Lights

4SELECT CYCLE Keypads

5START Keypad

6LED Light

801184

Display Identification

Light Emitting Diodes (LEDs)

LIGHT EMITTING DIODES (LEDs) are used to

indicate the chosen cycle status. Refer to LED

descriptions below.

START LED

The START keypad LED flashes whenever the washer

is not in a cycle and the full vend price has been

satisfied. When the START keypad is pressed, the

cycle will begin or resume. The START LED will shut

off when the START keypad is pressed.

WASH LED

The WASH LED is lit at the beginning of a wash cycle

and will remain lit until the wash cycle is complete.

RINSE LED

The RINSE LED is lit at the beginning of the rinse or

extra rinse cycle and will remain lit until the cycle is

complete.

SPIN LED

The SPIN LED is lit for all spin cycles.

DOOR LOCKED LED

The DOOR LOCKED LED is lit whenever the door is

locked. The door cannot be opened when the DOOR

LOCKED LED is lit.

Four 7-Segment Digits

The 7-SEGMENT DIGITS are used to display the

time remaining in a cycle, vend price, error messages

and descriptive codes. When displaying the time

remaining, the time value is displayed on the right side

of the display. When displaying the vend price, the

value is displayed on the left side of the display.

During diagnostic testing or manual programming of

the control, these digits will display descriptive codes

and values (as described in Entering the Manual

Mode).

Washer Operation

Start Up

When power is applied to the washer, the control will

display its software version as “SXXX” (“XXX” is the

version number) for two seconds. If the control was

not powered down during a running cycle, it will enter

the Ready Mode.

Ready Mode

Figure 2

In Ready Mode, the PERM PRESS/WARM (default

cycle) LED is lit, and the full vend price is displayed

as left justified. The user may select a different cycle,

if desired. (In card reader machines, if the current

cycle has a vend price which differs from the default

cycle, the display will be updated to show the new

price.) If another cycle is selected, the control will

flash the amount needed to satisfy the vend price

shown on the display. If the vend price is not satisfied

within one minute, the washer control will stop

flashing the vend price and return to the default cycle.

The display will continue to show the remaining vend

price needed to start a cycle and will credit any vend

entered by the user.

Vends may be satisfied by a coin drop, start pulses, or

by a third party card reader. If a coin drop is used, the

remaining vend price will decrease with each coin

entry. If start pulses are used, the remaining vend price

will decrease with each received pulse. Once the vend

price is satisfied, the START LED will begin to flash.

If a third party card reader is used, the START LED

will begin to flash when a valid cash card is entered

into the reader.

When the START keypad is pressed, the door will lock

and the washer will start. The START LED will stop

flashing and the WASH LED will be lit. The display

will change to show the remaining cycle time on the

right side of the display. The appropriate LEDs will

light while the machine passes through different cycle

steps. Any coin entered after the first fill cycle will be

added to the total coin counter, but the user will not be

able to change cycles.

When a cycle is complete, the Four-Digit Display will

show “00” until the washer door is opened, a keypad is

pressed, a coin or card is entered, or a start pulse is

received. When one of these instances occurs, the

Four-Digit Display will revert back to the Ready

Mode.

Closing the Washer Door

If the door is not closed when the vend price is

satisfied, the Four-Digit Display will show “door”

until the door is closed. Once the door is closed, the

START keypad must be pressed again to lock door and

start cycle. If the door does not lock within 15 seconds

of being closed, “E dl” will be displayed indicating a

door lock error and the machine will shut off.

Signals

There are four instances when a signal may sound

during washer operation. The owner may program the

signal to be turned on or off (refer to Programming

MDC, option 6). These four instances are listed below:

1. Keypad Depression Signal

The signal will sound for.25 seconds each time a

keypad is pressed.

2. Coin Input/Start Pulse Input/Card Insertion

Signal

The signal will sound for.25 seconds each time a

coin or start pulse is received or a card is entered.

3. Machine Error Signal

The signal will sound for 15 seconds if an error

occurs.

4. Vend Satisfaction Signal

The signal will sound one second on and one

second off for 10 seconds when the vend price is

satisfied.

FLW2R

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HC18NC2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems H236I Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TV6000WN Service-Handbuch

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen FF7008WN Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems PHM798N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SC70 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems DRY2033N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW100AV Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems AWNE8RSN115FW01 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Home Laundry Automatic Washer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HF455 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SF18VNV Wartungs- und Serviceanleitung

Alliance Laundry Systems

Alliance Laundry Systems CHM160C Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems 685981R1 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 802753R4 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount SC27SN Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 38903R6 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWB19A*-1109 series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 800138R2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems C003292ENR1 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FLW39H Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LTZ97A N2802 Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FLW700C Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung