Alliance Laundry Systems TR7000WN Bedienungsanleitung

Installation Instructions

for Topload Washers

Original Instructions

Keep These Instructions for Future Reference.

CAUTION: Read the instructions before using the machine.

(If this machine changes ownership, this manual must accompany machine.)

www.speedqueen.com Part No. 204104ENR1

September 2017

Table of Contents

Dimensions and Specifications................................................................ 4

Installation............................................................................................. 5

Before You Start............................................................................................. 5

Supplies..................................................................................................... 5

Parts Included............................................................................................. 5

Order of Installation Steps............................................................................5

Remove the Shipping Brace and Shipping Plug................................................. 5

Wipe Out Inside of Washtub............................................................................ 6

Connect Fill Hoses..........................................................................................6

Water Supply Requirements......................................................................... 6

Connecting Hoses....................................................................................... 7

Connect Drain Hose to Drain Receptacle.......................................................... 7

Standpipe Installation.................................................................................. 7

Low Standpipe Installation...........................................................................8

Wall Installation.......................................................................................... 8

Laundry Tub Installation..............................................................................8

Position and Level the Washer......................................................................... 9

Plug In the Washer..........................................................................................9

Electrical Requirements............................................................................. 10

Earth/Ground Instructions.......................................................................... 10

Check Lid Lock............................................................................................ 11

Check Installation......................................................................................... 11

Installer Checklist.................................................................................12

written consent of the publisher.

DO NOT COPY or TRANSMIT

3 Part No. 204104ENR1

Dimensions and Specifications

TLW2279N_SVG

GFE

A 28 in. [711 mm]

B 22.13 in. [562 mm]

C (to controls) Electronic Control: *41.25 in. [1048 mm]

Knob Control: *40.75 [1035 mm]

D *53 in. [1346 mm]

E 26 in. [660 mm]

F 0.4 in. [10 mm]

G 25.63 in. [651 mm]

H *29 in. [737 mm]

I *42.75 in. [1086 mm]

J *36 in. [914 mm]

*With leveling legs turned into base.

Dimensions and Specifications

DO NOT COPY or TRANSMIT

4 Part No. 204104ENR1

Installation

Before You Start

Supplies

For most installations, the basic supplies you will need are:

TLW2218N_SVG

NOTE: A cloth rag and all-purpose cleaner are also

needed.

1. Safety Glasses

2. Wood Block

3. Gloves

4. Wrench

5. Screwdriver

6. Pliers

7. Level

Figure 1

NOTE: If the washer is delivered on a cold day (below

freezing), or is stored in an unheated room or area dur-

ing the cold months, do not attempt to operate it until

the washer has had a chance to warm up.

NOTE: Install dryer before washer. This allows room for

attaching exhaust duct.

NOTE: This appliance is suitable for use in countries

having a warm, damp climate.

Parts Included

An accessories bag has been shipped inside your washer. It in-

cludes:

• Two fill hoses with washers and filter screens

• Four rubber feet

• Beaded strap

• Installation Instructions

• User’s Guide

• Warranty Bond

Order of Installation Steps

The proper order of steps must be followed to ensure correct in-

stallation. Refer to the list below when installing your unit.

1. Put on safety glasses and gloves.

2. Remove the shipping brace and shipping plug.

3. Wipe out inside of the washer.

4. Connect the fill hoses.

5. Connect the drain hose to the drain receptacle.

6. Position and level the washer.

7. Plug in the washer.

8. Check the lid lock.

9. Check installation.

Remove the Shipping Brace and

Shipping Plug

1. Remove the shipping brace from under the lid.

2. The shipping plug will be released from the base of the wash-

er when removing the cardboard base from the washer.

The shipping brace and plug should be saved and must be rein-

stalled whenever washer is moved or transported to a new loca-

tion. This will prevent damage to washer components.

Do not tilt washer to front or sides when moving.

Refer to the User's Guide for instructions on reinstalling the ship-

ping materials.

Installation

DO NOT COPY or TRANSMIT

5 Part No. 204104ENR1

TLW2280N_SVG

1. Shipping Brace

2. Shipping Plug

3. Cardboard Base

Figure 2

Wipe Out Inside of Washtub

Prior to first wash, use an all purpose cleaner or a detergent

and water solution and a damp cloth to remove shipping dust

from inside of washtub.

TLW2281N_SVG

Figure 3

Connect Fill Hoses

WARNING

Under certain conditions, hydrogen gas may be pro-

duced in a hot water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLO-

SIVE. If the hot water system has not been used for

such a period and before using the washer, turn on

all hot water faucets and let the water flow from each

for several minutes. This will release any accumulat-

ed hydrogen gas. The gas is flammable. Do not

smoke or use an open flame during this time.

W029

Mixing Valve Flow Rates

Pressure

psi [kPa]

HOT

gallons per

minute [liters

per minute]

COLD

gallons per

minute [liters

per minute]

WARM

gallons per

minute [liters

per minute]

20 [138] 3.4 [12.9] 3.4 [12.9] 4.0 [15.1]

120 [827] 4.6 [17.4] 4.6 [17.4] 4.6 [17.4]

Water Supply Requirements

Water supply faucets must fit standard 3/4 inch [19 mm] female

garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-

ON CONNECTIONS.

NOTE: Water supply faucets should be readily accessi-

ble to permit turning them off when washer is not being

used.

Recommended cold water temperature is 50° to 75° Fahrenheit

[10° to 24° Celsius]. Recommended maximum hot water temper-

ature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture

of hot and cold water. Warm water temperature is dependent upon

the water temperature and the pressure of both the hot and cold

water supply lines.

WARNING

To prevent personal injury, avoid contact with inlet

water temperatures higher than 125° Fahrenheit [51°

Celsius] and hot surfaces.

W748

Water pressure must be a minimum of 20 to a maximum of 120

pounds per square inch [minimum of 138 to a maximum of 827

kPa] static pressure measured at the faucet.

Installation

DO NOT COPY or TRANSMIT

6 Part No. 204104ENR1

NOTE: Water pressure under 20 pounds per square

inch [138 kPa] will cause an extended fill time in the

washer.

Turn on the water supply faucets and flush the lines for approxi-

mately two minutes to remove any foreign materials that could

clog the screens in the water mixing valve. This is especially im-

portant when installing your washer in a newly constructed or

renovated building. Build-up may have occurred during construc-

tion.

Connecting Hoses

1. Remove the two plain rubber washers and two filter screens

from the accessories bag.

2. Install them into each end of the fill hoses as shown in Figure

4 . The screen must be facing outward.

3. Screw hose couplings with the filter screens onto the water

faucets until they are finger-tight. Use the red color-coded

hose for the hot water connection and the blue color-coded

hose for the cold water connection.

4. Then, using a pliers, screw approximately 1/4 turn.

5. Screw hose couplings from other end of hoses onto the water

mixing valve until they are finger-tight. Make sure the red

color-coded hose from the hot water faucet goes to the water

mixing valve marked “H” and the blue color-coded hose from

the cold faucet goes to the valve marked “C”. Refer to Figure

Figure 4 .

6. Then, using a pliers, screw approximately 1/4 turn.

IMPORTANT: DO NOT cross thread or overtighten

couplings. This will cause them to leak.

7. Turn water on and check for leaks.

8. If leaks are found, turn off the water, unscrew hoses and rein-

stall them until there are no leaks.

IMPORTANT: Turn off water supply whenever there

will be an extended period of non-use.

TLW1988N_SVG

HOT

COLD

1. Filter Screen (Screen must be facing outward)

2. Fill Hose

3. Rubber Washer (Plain)

4. Cold Water Connection

5. Hot Water Connection

6. Install this end of hose to valve connections at rear of

washer.

7. Install this end of hose to water supply faucet.

8. Faucet

Figure 4

IMPORTANT:

Hoses and other rubber parts deteriorate after extend-

ed use. Hoses may develop cracks, blisters or material

wear from the temperature and constant high pressure

they are subjected to.

All hoses should be checked on a monthly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be re-

placed immediately. All hoses should be replaced ev-

ery five years.

Connect Drain Hose to Drain

Receptacle

1. Remove the drain hose from its shipping position on the rear

of the washer by unhooking the hose from the retainer clamp.

2. Install the drain hose into the drain receptacle (standpipe, wall

or laundry tub) following the instructions below.

NOTE: Drain receptacle must be capable of handling

a minimum of 1-1/4 inch [32 mm] outside diameter

drain hose.

Standpipe Installation

1. Check standpipe height. The recommended height for the

standpipe is 36 inches [914 mm]. Standpipes higher than 4

feet [1220 mm] will result in slower draining and may extend

cycle times.

NOTE: Machine will not drain if standpipe is higher

than 8 feet [2438 mm].

Installation

DO NOT COPY or TRANSMIT

7 Part No. 204104ENR1

2. Place the adapter into the standpipe.

IMPORTANT: To prevent siphoning, do not place

any ribbed portion of the drain hose into the stand-

pipe.

3. Remove the beaded strap from accessories bag and place

around standpipe and drain hose, approximately 12 inches

[300 mm] down from the top of pipe. Refer to Figure 5 .

a. Insert the end of the beaded strap into the larger hole

found on the end of the strap.

b. Tighten to desired fit.

c. Lock strap in place by pulling beaded strap into the ta-

pered smaller opening of the beaded strap end. A distinct

snap noise should be heard once the strap is properly seat-

ed.

d. Pull on the strap once locked in place to ensure beaded

strap is properly installed. This will prevent the drain hose

from dislodging from drain receptacle during use.

TLW2282N_SVG

1. Ribbed Portion of Drain Hose

2. Standpipe Adapter

3. Beaded Strap

4. Standpipe - 2 in. [51mm] or 1-1/2 in. [40 mm] Diameter

5. 36 in. [914 mm] Recommended Height

6. 12 in. [305 mm]

Figure 5

Low Standpipe Installation

If standpipe is lower than 36 inches [914 mm], you must install

No. 562P3 Siphon Break Kit. This kit is available (as optional

equipment at extra cost) through an authorized dealer or parts dis-

tributor. Installation instructions are supplied with the kit.

TLW2283N_SVG

1. 562P3 Siphon Break Kit

2. Standpipe

3. Drain Hose

Figure 6

Wall Installation

Check wall drain height. The recommended height for the drain

is 36 inches [914 mm].

For installations of this type, the drain hose MUST be secured to

one of the fill hoses using the beaded strap from accessories bag.

Refer to Figure 7 .

W329I_SVG

1. Beaded Strap (tape if necessary)

2. Standpipe Adapter

Figure 7

Laundry Tub Installation

For this type of installation, the drain hose MUST be secured to

the stationary tub to prevent hose from disloding during use. Use

the beaded strap (supplied in accessories bag) to secure hose.

Installation

DO NOT COPY or TRANSMIT

8 Part No. 204104ENR1

We recommend leaving the standpipe adapter on the drain hose

for this type of installation.

TLW2284N_SVG

1. Beaded Strap (tape if necessary)

Figure 8

Position and Level the Washer

1. Position washer so it has sufficient clearance for installation

and servicing.

2. Place washer in position on a clean, dry, and reasonably firm

floor. Installing the washer on any type of carpeting is not rec-

ommended.

3. For easier access to leveling legs, prop up washer with a

wooden block.

TLW2285N_SVG

1. Wood Block

Figure 9

4. Place rubber cups (from accessories bag) on all four leveling

legs.

TLW2286N_SVG

1. Level

2. Locknut

3. Leveling Leg

4. Rubber Cup

5. Washer Base

Figure 10

5. Place a level on the cabinet top and check if the washer is lev-

el from side to side and front to back.

6. If washer is not level, tilt washer back to access the front lev-

eling legs. Loosen the locknuts and adjust legs by screwing

into or out of washer base.

7. Once adjusted, tilt the washer forward on front legs and lower

back down into position to set the rear self-leveling legs.

8. Washer must not rock. When washer is level and does not

rock, tighten locknuts securely against bottom of washer base.

If these locknuts are not tight, washer will not remain station-

ary during operation.

Improper installation or flexing of weak floor will cause exces-

sive vibration.

Do not slide washer across floor once the leveling legs have been

extended, as legs and base could become damaged.

9. Verify that unit does not rock.

Installation

DO NOT COPY or TRANSMIT

9 Part No. 204104ENR1

Plug In the Washer

Electrical Requirements

120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug

NOTE: The wiring diagram is located in the control

hood.

WARNING

To reduce the risk of fire, electric shock, serious in-

jury or death, all wiring and protective earth/ground

connections MUST conform with the latest edition of

the National Electrical Code, ANSI/NFPA No. 70, and

such local regulations as might apply. It is the cus-

tomer’s responsibility to have the wiring, fuses and

circuit breakers installed by a qualified electrician to

make sure adequate electrical power is available to

the washer.

W824

When plugging in the washer:

• DO NOT overload circuits.

• DO NOT use an extension cord.

• DO NOT use an adapter.

• DO NOT operate other appliances on the same circuit. Use

separately fused 15 Amp circuits.

The washer is designed to be operated on a separate branch, po-

larized, three-wire, effective earth/ground, 120 Volt, 60 Hertz,

AC (alternating current), circuit protected by a 15 ampere fuse,

equivalent fusetron or circuit breaker.

The three-prong earth/ground plug on the power cord should be

plugged directly into a polarized three-slot effective earth/ground

receptacle rated 110/120 Volts AC (alternating current) 15 Amps.

Refer to Figure 11 to determine correct polarity of the wall recep-

tacle.

Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/

Ground Circuit

TLW2287N_SVG

1 3

1. L1

2. Earth/Ground

3. Neutral Side

4. Round Earth/Ground Prong

5. Neutral

6. 0 V.A.C.

7. 120 ± 12 V.A.C.

8. 120 ± 12 V.A.C.

Figure 11

WARNING

To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to connect

the washer to the electric power source.

W082

Earth/Ground Instructions

This appliance must be properly connected to protective earth/

ground. In the event of malfunction or breakdown, the earth/

ground will reduce the risk of electric shock by providing a path

of least resistance for electric current.

The appliance is equipped with a cord having an equipment earth/

ground conductor and a three-prong earth/ground plug. The plug

must be plugged into an appropriate outlet that is properly instal-

Installation

DO NOT COPY or TRANSMIT

10 Part No. 204104ENR1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems BWT820*N1102 Programmierhandbuch

Alliance Laundry Systems

Alliance Laundry Systems UX55PVXF6 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AWN311SP111TW01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SC70 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems W001C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SWTT21 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems B-Series Installations- und Betriebshandbuch

Alliance Laundry Systems

Alliance Laundry Systems UW35P2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW100AV Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems FLW1525C Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems CHM1772C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HFNNERSP116CW01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 802749R2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Frontload Washer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F232139R3 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Cygnus Ultra Pro Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SF135PV Wartungs- und Serviceanleitung

Alliance Laundry Systems

Alliance Laundry Systems H370I Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems Frontload Washers Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWK23A*-3050 series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F8437801 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems V-Series Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems LTS84A*H Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung