Alliance Laundry Systems UX55PVXF6 Betriebsanleitung

Programming

www.comlaundry.com

Washer-Extractors

Cabinet Freestanding

WE-8 Computer

Part No. 9002101R2

July 2011

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

19002101

NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover

all possible conditions and situations that may occur. It must be understood that common sense, caution,

and carefulness are factors which cannot be built into these washers. These factors MUST BE supplied by

the person(s) installing, maintaining, or operating the washer.

Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not

understand.

Failure to install, maintain, and/or operate this machine according to the manufacturer's

instructions may result in conditions which can produce bodily injury and/or property

damage. W030

WARNING

means without the expressed written consent of the publisher.

2© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9002101

Table of

Contents

Introduction......................................................................................... 3

Model Identification ............................................................................. 3

Programming ...................................................................................... 4

Setup of the Machine............................................................................ 4

Version of Control................................................................................ 7

Language on Display

(Version 1.15 and later ONLY)...................................................... 7

Setup of the Chemical Hold Feature

(Version 1.11 and later ONLY) ....................................................... 7

Program Storing Mode ......................................................................... 7

Explanation of the Step Functions........................................................ 8

Example: Making a New Program ....................................................... 14

Edit a Cycle........................................................................................... 18

Change a Complete Step.................................................................. 18

Changing the Time of a Step ........................................................... 20

Delete a Step.................................................................................... 22

Insert a Step...................................................................................... 23

Delete a Cycle....................................................................................... 25

Reloading Previous Settings................................................................. 26

Cycle Count.......................................................................................... 27

Reading Cycle Count....................................................................... 27

Calibration of the Machine................................................................... 28

Speed Calibration.................................................................................. 29

Inverter Drive Error Codes............................................................... 49

9002101

Introduction

Model Identification

Information in this manual is applicable to these

models:

UX55PVXF6 UX055PVXF7

UX55PVXF7

9002101

4© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Programming

Setup of the Machine Turn key from Run to Program

To go to the main setup of the machine, press

“Auxiliary”, “2”, “9”.

To change the machine type, press the “Advance”

button. The following types are possible:

_X18PV _X55PV _X135PV

_X25PV _X75PV _X165PV

Press the “Advance” button until the right type of

machine is selected. Press the “Enter” button.

Select the desired units.

NOTE: English means level in inch and

temperature in °F. Metric means level in cm and

temperature in °C.

Press the “Advance” button to change the units.

Press the “Enter” button.

Select the type of drain valve.

Press “1” to change drain 1 to pump or valve.

Press “2” to change drain 2 to pump, valve or none.

Program Cycle 00

Units: English

System Program

_X18PV

System Program

_X25PV

Units: Metric

Drain 1 : Valve

Drain 2 : None

Drain 1 : Pump

Drain 2 : None

RUN PROGRAM

Programming

9002101 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Press the “Enter” button to select options.

Press the “Aux Fill” button for auxiliary fill option or

press “Enter” for heating.

If heating is selected, the user can fill in the kW of the

electrical heating (example: 9 kW).

Press “0”, “9”.

Press “Enter” to select advance mode in run mode yes

or no.

Press “Advance” to change between yes and no.

Options :

Advance : Yes

Advance : No

Options :

Aux Fill

Heating : 6 kW

Heating : 9 kW

Programming

9002101

6© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Press “Enter” to set the hysteresis level (level at which

water drops before it senses it must refill).

If English is selected for units, this value will be in

inches. If Metric is selected for units, this value will be

in cm.

Select between 1 to 9 cm or inches.

Press “Enter” to select the temperature hysteresis

(level at which temperature drops before machine

senses it must reheat).

If English is selected for units, this value will be in °F.

If Metric is selected for units, this value will be in °C.

Select 1 to 9 °C or °F.

Press the “Enter” button to set the spin retries.

Select 1 to 9 spin retries.

Press “Enter” to set the network address of the

machine. If this is not used, press “Enter”.

The address of the machine has to be set if you

network the machine. Each machine should have a

different address.

Fill in between 00 and 99.

Press “Enter” to finish the settings.

Press “Enter” to save the settings or press “Stop” to

exit without saving.

Level : hyst 2"

Enter to save ?

Program Cycle 00

Temp : hyst 3°F

Spin retries : 5

Address : 0

Programming

9002101 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Version of Control

To determine control version, apply power to machine.

Control will display version of control (i.e., 1.15).

Language on Display (Version 1.15 and

later ONLY)

To set a different language on the WE-8 display:

1. Turn key from RUN to PROGRAM.

2. Press “Auxiliary”, “2” and “9” to enter set-up

mode.

3. English will display. Press “Advance” until

desired language displays (French, Italian,

Spanish and German).

4. Press “Enter” keypad.

5. Press “Enter” to advance through set-up mode.

6. Wait until information is saved.

7. Turn key from PROGRAM to RUN.

8. Display will read language chosen for all cycles.

Setup of the Chemical Hold Feature

(Version 1.11 and later ONLY)

•At power up, verify that model is at least

version 1.11. Refer to version of Control Section.

Earlier versions do not have this chemical hold

feature.

•Insert key into key switch and turn to Program.

•Push the Auxiliary key, the 2 key, and the 9 key

in succession to enter System Program Mode.

•Push the Start key 10 times to arrive at the

Chemical hold choice.

•Push the Add Cycle/Advance key to toggle the

Chemical hold feature either Yes (on) or No (off).

•Push the Start key twice to save changes and exit

System Program Mode.

•Turn key switch to Run.

NOTE: If chemical hold is on, then a switch

closure/opening between pins 1 and 4 of the COIN

header on the output board will control supplies 4

through 9. A closure will turn the programmed

supply/ies on and count down the time for the

supply to be on. An opening will turn the

programmed supply/ies off and halt the time for

the supply to be on.

NOTE: If chemical hold is off, then supplies 4

through 9 are controlled exactly like supplies 1

through 3. A switch closure/opening between pins 1

and 4 of the COIN header on the output board will

have no effect.

Program Storing Mode

The WE-8 control is capable of 99 total Cycles. One

cycle contains 1 or more steps.

One step is a function of the wash program

(example: heat).

Choose between the following functions:

Fill: To fill the machine with water.

Wash: Wash action of the machine.

Supply: To add detergent to the wash (liquid or

powder).

Cooldown: Cool to programmed temperature.

Heat: To heat the water.

Soak: The wash will be soaked for a

programmed time and a programmed

temperature.

Aux: A relay contact will close for a

programmed time.

Spin: To spin the machine for a programmed

time and RPM.

Drain: To drain the water from the machine.

Programming

9002101

8© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Explanation of the Step Functions

Fill:

Choose between 4 water inlet configurations and

3waterlevels.

Water Inlet Configurations:

Cold: Only opens the cold water valve.

Hot: Only opens the hot water valve.

Warm: Opens the cold and hot water valves.

Aux Fill: Opens an auxiliary water valve

if installed.

Water Levels:

Low: Low water level.

Med: Medium water level.

High: High water level.

The inlet configurations and the fill levels appear on

the keypad, keys 1, 2, 3 and 8.

Be sure to select first the inlet configuration and then

the water level.

Then you will be asked for the step time limit.

Example: Warm Low (time limit 5 minutes

30 seconds)

NOTE: If a fill error occurs, then machine has

2 minutes to finish filling. If after 2 minutes it has

not finished filling, cycle is aborted.

Step XX Cycle XX

Warm

Step XX Cycle XX

Warm Low

Step XX Cycle XX

0 min

Step XX Cycle XX

5 min 30 sec

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems 201932R5 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen LFNE5B Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HC18PC2 Programmierhandbuch

Alliance Laundry Systems

Alliance Laundry Systems AFNE9BSP113TN01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW POCKET HARDMOUNT UW35B2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F232136R5 Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems D1627ENR5 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FLW1525C Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems MB26 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 800797 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LTS87A*H Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SVN255P Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems WFF100 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FTS90A*N Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems FLW1526C Original Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW150PV Series Programmierhandbuch

Alliance Laundry Systems

Alliance Laundry Systems StGeorge Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HY105 HC-200 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW35TV Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F232179R5 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HY125_MICRO Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems W001C Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung