Alliance Laundry Systems UW POCKET HARDMOUNT UW35B2 Betriebsanleitung

Programming

www.comlaundry.com

Washer-Extractors

UW Pocket Hardmount

B-Series Microcomputer

2 Speed

Models UW35B2 and UW60B2

PHM1

NORMAL

LIGHT SOIL

UNIFORMS

HEAVY SOIL

STAINED

DELICATE

HOT

HOT HOT

HOT

WARM

COLD

START

PERM PRESS

VISA

60C 60C

40C 40C

95C 95C

30C

WASH

ADD

BLEACH

RINSE

SPIN

DOOR

DOMESTIC MODELS

INTERNATIONAL MODELS

Part No. F232168R2

November 2005

NOTA: El manual en

español aparece después

del manual en inglés.

PHM1392C

means without the expressed written consent of the publisher.

F232168 1

Table of

Contents

Safety Information.............................................................................. 3

Important Safety Instructions ............................................................... 3

Programming ...................................................................................... 5

Entering Program Mode ....................................................................... 5

Determining Firmware ID Code........................................................... 5

Setup Mode (For Models With Firmware ID Code

“o2HC”, “o2UC”, “ouHC” and “ouUC”) ...................................... 6

Cycle and Error Count.......................................................................... 6

Setup Mode (For Earlier Models) .................................................... 7

Cycle and Error Count.......................................................................... 7

Programming Cycle Segments......................................................... 8

Options for Each Segment .................................................................... 9

To Edit an Entire Wash Cycle Formula................................................ 13

Wash 1 – Wash 4 ............................................................................. 13

Rinse 1 – Rinse 4 ............................................................................. 14

Abnormal Conditions............................................................................ 16

Door Open During Operation .......................................................... 16

Excessive Fill Time.......................................................................... 16

Door Will Not Open......................................................................... 16

Excessive Drain Time ...................................................................... 16

Drain Error (For Models With Firmware ID Code

“o2HC”, “o2UC”, “ouHC” and “ouUC”) ...................................... 16

Temperature Probe Sensor Problem ................................................ 16

Frame Limit Switch Trip ................................................................. 16

Rapid Advance (For Models With Firmware ID Code

“o2HC”, “o2UC”, “ouHC” and “ouUC”) ...................................... 17

How to Rapid Advance During All Steps (Except First Fill Step) .. 17

How to Rapid Advance (During First Fill Step).............................. 17

Test Cycle ............................................................................................. 17

Permanent Diagnostic Test Cycle......................................................... 18

Cycle Charts for Domestic OPL Models Built After April 2005

(Displays P-F5) .................................................................................. 20

Cycle Charts for Domestic OPL Models Built Prior to April 2005

(Displays P-F1) .................................................................................. 23

Cycle Charts for International OPL...................................................... 26

2F232168

Notes

F232168

Safety Information

Precautionary statements (“DANGER,” “WARNING,”

and “CAUTION”), followed by specific instructions,

are found in this manual and on machine decals. These

precautions are intended for the personal safety of the

operator, user, servicer, and those maintaining the

machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

IMPORTANT: The word “NOTE” is used to

communicate installation, operation, maintenance

or servicing information that is important but not

hazard related.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Refer to the grounding instructions in the

installation manual for the proper grounding of

the washer.

3. Do not wash textiles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, kerosene, waxes, cooking oils,

dry-cleaning solvents, or other flammable or

explosive substances as they give off vapors that

could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapors that

could ignite or explode.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not

been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. The gas is

flammable; do not smoke or use an open flame

during this time.

6. Do not allow children to play on or in the washer.

Close supervision of children is necessary when

the washer is used near children. This is a safety

rule for all appliances.

7. Before the washer is removed from service or

discarded, remove the door to the washing

compartment.

8. Do not reach into the washer if the wash drum is

moving.

DANGER indicates the presence of a

hazard that will cause severe personal

injury, death, or substantial property

damage if the danger is ignored.

DANGER

WARNING indicates the presence of a

hazard that can cause severe personal

injury, death, or substantial property

damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a

hazard that will or can cause minor

personal injury or property damage if the

caution is ignored.

CAUTION

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions:

W023

WARNING

Safety Information

F232168

9. Do not install or store the washer where it will be

exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or

attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that the user understands and has the

skills to carry out.

12. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to

connect the washer to the electrical power source.

13. Use washer only for its intended purpose,

washing textiles.

14. ALWAYS disconnect the washer from electrical

supply before attempting any service. Disconnect

the power cord by grasping the plug, not the cord.

15. Install the washer according to the installation

instructions. All connections for water, drain,

electrical power and grounding must comply

with local codes and be made by licensed

personnel when required.

16. To reduce the risk of fire, textiles which have

traces of any flammable substances such as

vegetable oil, cooking oil, machine oil,

flammable chemicals, thinner, etc. or anything

containing wax or chemicals such as in mops and

cleaning cloths, must not be put into the washer.

These flammable substances may cause the

fabric to catch on fire by itself.

17. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

18. Keep washer in good condition. Bumping or

dropping the washer can damage safety features.

If this occurs, have washer checked by a qualified

service person.

19. Replace worn power cords and/or loose plugs.

20. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

21. Loading door MUST BE CLOSED any time the

washer is to fill, tumble or spin. DO NOT

bypass the loading door switch by permitting the

washer to operate with the loading door open.

22. Always read and follow manufacturer’s

instructions on packages of laundry and cleaning

aids. Heed all warnings or precautions. To reduce

the risk of poisoning or chemical burns, keep

them out of the reach of children at all times

(preferably in a locked cabinet).

23. Always follow the fabric care instructions

supplied by the textile manufacturer.

24. Never operate the washer with any guards and/or

panels removed.

25. DO NOT operate the washer with missing or

broken parts.

26. DO NOT bypass any safety devices.

27. Failure to install, maintain, and/or operate this

washer according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT

SAFETY INSTRUCTIONS appearing in this

manual are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining, or operating the washer.

Any problems or conditions not understood should be

reported to the dealer, distributor, service agent or the

manufacturer.

F232168

Programming

NOTE: The machines are factory-programmed

with basic cycles to make the units operational

without programming at the installation.

Entering Program Mode

1. Open control compartment lid.

2. Locate Program/Run switch on the computer

board. (This is accessed through a cutout in the

metal control unit cover.) This switch protrudes

from the rear of the electronic control unit cover.

3. Flip switch to the left (as seen from the front of

machine) to enter Program Mode.

4. Display will show a temperature.

Determining Firmware ID Code

1. Turn on the main power source (circuit breaker or

cut-off switch on wall).

2. Display will show Firmware ID code (i.e.,

“o2UC” and “ouUC” etc...).

3. Record Firmware ID Code for future reference.

Programming

F232168

Setup Mode (For Models With Firmware ID

Code “o2HC”, “o2UC”, “ouHC” and

“ouUC”)

NOTE: In Setup Mode, certain machine functions

can be configured. The settings in this mode are

related to how the machine is equipped from the

factory. Usually, these would not be changed in this

field.

NOTE: Enter Setup Mode through the Program Mode.

1. Press (*) key. Display will show “FAr” or “CEL”.

NOTE: This selects whether temperatures display

in degrees Fahrenheit (F) or Celsius (C), if control

is equipped with a temperature sensor. Press the

(∧)or (∨) key to change.

NOTE: Changing degrees “FAr” or “CEL” only

has an effect if the control has a temperature probe

connected and/or heat capability.

2. Press START key.

3. Model will display “HEAt” or “noHt”. Change

the selection by pressing the (∧) or (∨) key.

4. Press START key to continue to the next step.

NOTE: If set for “HEAt”, the control has heat

capability enabled. The washer-extractor MUST

have electric or steam heat, and a temperature

probe. If display shows “noHt”, or if the message

“HEAt” or “noHt” does NOT display, the control

does NOT have heat capability.

5. Certain models will display “EFIL” or “ESUP”.

For these models, the control provides a spare

output (for certain models). The spare output can

be set up to control an extra fill valve (“EFIL”),

with the ability to fill to a programmable water

level (just as for regular fills), OR the spare

output can be set up to control an extra chemical

supply signal (“ESUP”).

6. Press START keypad.

7. Certain models display “bEEP” (control sounds

beeper during Add Bleach [Supply 2]) or “nobP”

(control does NOT sound beeper during Add

Bleach [Supply 2]). Change selection by pressing

(∧) or (∨) keypad.

8. Press START keypad.

NOTE: If “EFIL” or “ESUP” does NOT display,

the extra fill capability is NOT present. If either

message does display, change the selection by

pressing the (∧) or (∨) key. Press START key to

return to Program Mode. Refer to “Programming

Cycle Segments” section for additional information.

9. “Adv” or “noAd” will display. If “Adv” is set,

control will advance to the next step when up

arrow keypad is pressed during a regular cycle. If

“noAd” is set, control cannot advance during a

regular cycle, but can advance during the factory

test cycle when up arrow keypad is pressed.

10. Press START (enter) keypad to continue to next

step.

11. “PtIM” or “EtIM” will display. “PtIM” means

control will not display remaining time in a cycle.

“EtIM” means control will display an estimated

remaining time for a fill and drain. Press the up

or down keypad to change “PtIM”/ “EtIM”

selection.

12. Press START (enter) keypad to continue to the

next step.

Cycle and Error Count

1. To read, enter Program Mode. Refer to Entering

Program Mode.

2. Press START (enter) keypad. Display shows

“Erdn” (indicates Drain Error count).

3. Press START (enter) keypad. Display shows a

number (2 or 3 digits) showing how many drain

errors have occurred. This number can range

from ‘00’ to ‘255’, and cannot be set to zero.

4. Press START (enter) keypad. Display shows

“ErFL” (indicates Fill Error count).

5. Press START (enter) keypad. Display shows a

number (2 or 3 digits showing how many fill

errors have occurred. This number can range

from ‘00’ to 255’, and cannot be set to zero.

6. Press START (enter) keypad. Display shows

“CYC “ (indicates Cycle count).

7. Press START (enter) keypad. Displays show a

number (up to 4 digits) showing how many

complete cycles have been operated. This

excludes cycles stopped because of an error.

8. Press START (enter) keypad.

9. If display does not show “E Pr”, control will

revert to normal program mode.

10. If display shows “E Pr”, this is for factory

reference regarding power interruption. Press

START (enter) keypad. A number will display.

Press START (enter) keypad. After a brief pause,

the control will display normal program mode.

Programming

F232168

Setup Mode (For Earlier Models)

NOTE: In Setup Mode, certain machine functions

can be configured. The settings in this mode are

related to how the machine is equipped from the

factory. Usually, these would not be changed in this

field.

NOTE: Enter Setup Mode through the Program

Mode.

1. Press (*) key. Display will show “FAr” or “CEL”.

NOTE: This selects whether temperatures display

in degrees Fahrenheit (F) or Celsius (C), if control

is equipped with a temperature sensor. Press the

(∧)or (∨)key to change.

NOTE: Changing degrees “FAr” or “CEL” only

has an effect if the control has a temperature probe

connected and/or heat capability.

2. Press START key.

3. Model will display “HEAt” or “noHt”. Change

the selection by pressing the (∧) or (∨) key.

4. Press START key to continue to the next step.

NOTE: If set for “HEAt”, the control has heat

capability enabled. The washer-extractor MUST

have electric or steam heat, and a temperature

probe. If display shows “noHt”, or if the message

“HEAt” or “noHt” does NOT display, the control

does NOT have heat capability.

5. Certain models will display “EFIL” or “ESUP”.

For these models, the control provides a spare

output (for certain models). The spare output can

be set up to control an extra fill valve (“EFIL”),

with the ability to fill to a programmable water

level (just as for regular fills), OR the spare

output can be set up to control an extra chemical

supply signal (“ESUP”).

6. Press START keypad.

7. Certain models display “bEEP” (control sounds

beeper during Add Bleach [Supply 2]) or “nobP”

(control does NOT sound beeper during Add

Bleach [Supply 2]). Change selection by pressing

(∧) or (∨) keypad.

8. Press START keypad.

NOTE: If “EFIL” or “ESUP” does NOT display,

the extra fill capability is NOT present. If either

message does display, change the selection by

pressing the (∧)or (∨)key. Press START key to

return to Program Mode. Refer to “Programming

Cycle Segments” section for additional information.

Cycle and Error Count

The control logs cycle count (total of all cycles

completed).

●To read, enter Program Mode.

●Press START (enter) key. Display will show the

cycle count.

●Press START (enter) key. Display will show

certain error conditions that may have been

recorded by the control.

●Read the information when consulting technical

assistance as needed.

●Step through the error log by pressing START

key repeatedly until display reverts to normal

Program Mode (showing a temperature).

Programming

F232168

Programming Cycle Segments

The machine is preprogrammed with eight wash cycle

formulas that can be edited.

To edit any of these cycles, enter Program Mode. In

Program Mode, cycles are selected by number

(1 through 8) as opposed to the Run Mode, where

cycles are selected by pressing one of the eight

corresponding keys. The keys must serve different

functions in each mode because there are more

functions than keys in Program Mode.

In Run Mode the top left key selects Cycle 1, the key

directly below it selects Cycle 2, etc. Figure 1 shows

which key selects each cycle in Run Mode.

After entering Program Mode, display will show a

temperature. Press the (∧) key to enter Cycle

Programming Mode. The display will reference cycles

by number. Cycle 1 will show first. Use the (∧) or (∨)

key to select cycle to be edited. Press START key to

move into the following menu of options (starting at

Table 1).

NOTE: While cycle is running, pressing the START

keypad shows the temperature. Pressing the

START keypad again returns display to time

remaining or displays temperature for several

seconds, depending on version software.

Figure 1

PHM538R

1Cycle 1 11 Door Open LED

2Cycle 2 12 Spin Cycle LED

3Cycle 3 13 Rinse Cycle LED

4Cycle 4/Up Edit 14 Add Bleach LED

5Cycle 5 15 Wash Cycle LED

6Cycle 6 16 Out-of-Balance Indicator Dot

7Cycle 7 (Variable-speed only)

8Cycle 8/Down Edit 17 High Water Level Indicator Dot

9START Keypad 18 Medium Water Level Indicator Dot

10 CLEAN FILTER Indicator LED

(Active only for C80 models)

19 Low Water Level Indicator Dot

PHM538R

NORMAL

LIGHT SOIL

UNIFORMS

HEAVY SOIL

STAINED

DELICATE

HOT

HOT HOT

HOT

WARM

COLD

START

PERM PRESS

VISA

60C 60C

40C 40C

95C 95C

30C

WASH

ADD

BLEACH

RINSE

SPIN

DOOR

16 17 18 19

DOMESTIC MODELS INTERNATIONAL MODELS

Andere Handbücher für UW POCKET HARDMOUNT UW35B2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems 685981R1 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 801529 Service-Handbuch

Alliance Laundry Systems

Alliance Laundry Systems AWN311SP111TW01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Home Laundry Automatic Washers Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems WB2 350B Series Wartungs- und Serviceanleitung

Alliance Laundry Systems

Alliance Laundry Systems Frontload Washer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AA3410 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems AFNE9BSP113TN01 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HWNLX2SP111CW01 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen AFNE9RSP Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HY105 HC-200 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CHM166C Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW35PV Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CFD14C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FTS90A*N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F232182R1 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems F232148 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems TR7104WN Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HC18NC2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 802734R6 Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems Cygnus Ultra Pro Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Cygnus Premium Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HFNBCF Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems PHM1263R Betriebsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung