ALTAI A2 Bedienungsanleitung

ALTAI A2 WIFI ACCESS POINT/BRIDGE

INSTALLATION GUIDE

（）

Version 1.0

Date: September, 2013

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

Altai Technologies Limited

Unit 209, 2/F,

East Wing, Building 17,

Hong Kong Science Park,

Shatin, New Territories,

Hong Kong

Telephone: +852 3758 6000

Fax: +852 2607 4021

Web: www.altaitechnologies.com

Customer Support Centre:

Email: supp[email protected]

Radio Frequency Interference Requirements

This device complies with Part 15 of FCC Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

3. This device should not be co-located or operating in conjunction with any

other antenna or transmitter.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

This equipment generates uses and can radiate radio frequency energy. If it is not

installed and used in accordance with the instructions, harmful interference to radio

communications may be caused.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance,(example –use only shielded

interface cables when connecting to computer or peripheral devices) any changes

or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

Warning

The user is advised to keep away from the base-station and antenna with at least

45cm when the base-station is in operation.

Please install a lightning arrestor to protect the base station from lightning dissipation

during rainstorms. Lightning arrestors are mounted outside the structure and must be

grounded by means of a ground wire to the nearest ground rod or item that is

grounded.

Disclaimer

All specifications are subject to changes without prior notice. Altai Technologies

assumes no responsibilities for any inaccuracies in this document or for any obligation

to update information in this document. This document is provided for information

purposes only. Altai Technologies reserves the right to change, modify, transfer, or

otherwise revise this publication without notice.

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

Contents

1. Introduction ........................................................................................................................................... 5

2. Field Installation .................................................................................................................................... 5

2.1. Check A2 WiFi Access Point/Bridge Packages ......................................................................... 5

2.2. Introducing A2 WiFi Access Point/Bridge.................................................................................... 7

2.3. Installing A2 WiFi Access Point/Bridge ......................................................................................... 8

2.4. 2.4 Mounting A2 WiFi Access Point/Bridge ................................................................................. 8

2.5. Connecting Ethernet cable to A2 waterproofing cable protector....................................11

2.6. General Antenna and Safety Recommendations .................................................................18

2.7. 5GHz Antenna Alignment LED .................................................................................................... 19

2.8. Grounding A2 WiFi Access Point/Bridge ...................................................................................20

2.9. Surge Protection ............................................................................................................................20

2.10. ESD Protection................................................................................................................................ 21

2.11. Resetting A2 WiFi Access Point/Bridge to factory default settings......................................21

2.12. Reviewing Installation Procedures ............................................................................................. 22

3. Typical Site Setups ..............................................................................................................................22

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

1. Introduction

This document is written to provide the information needed to mount A2 WiFi Access

Point/Bridge and A2 antennas on site location.

This document is applicable for hardware platform A2 and the following models.

Product name : A2 WiFi Access Point/Bridge

Model number : AP5822

It is assumed that site survey has been performed. And appropriate antenna pole

and AP locations have been selected. Good site installation plan should consist of site

map, drawing illustrating AP and poles locations, antenna bearing/down-tilt, antenna

height and plan on network topology.

User may need to refer the following documents during A2 installation and

configuration.

[1] A2 Configuration Manual

[2] A2 WiFi Access Point/Bridge Data Sheet

2. Field Installation

2.1. Check A2 WiFi Access Point/Bridge Packages

Check the package against the packing list to ensure all equipment and necessary

parts are included. Typical shipment consists of equipment and parts as shown below.

Please contact the sales representative if there is any difference from the packing list.

Moreover, verify if the equipment has any physical defect. If so, please contact the

sales representative for repair or replacement.

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

Figure 2-1 typical A2 Package

Product:

A2 WiFi Access Point/Bridge × 1

Accessories:

Mounting Kit × 1 (Set)

One PoE Power Injector ×1

Waterproof Plug × 1 (Set)

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

Figure 2-2 Mounting Kit detail

2.2. Introducing A2 WiFi Access Point/Bridge

Figure 2-3 A2 Back View

Note:

1. Warranty will be voided if warranty labels are broken

2. Highly recommended to configure the bridge setting (e.g. the Frequency

channel, remote bridge MAC, security type) before site installation.

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

2.3. Installing A2 WiFi Access Point/Bridge

Before site installation, please prepare the following tools and accessories:

Tools:

1) Screw Driver

2) Sealing Tape

Accessories

1) Grounding Kit × 1

2) Ethernet Cable × 2

3) Waterproof Seal

2.4. 2.4 Mounting A2 WiFi Access Point/Bridge

1. Install the mounting bracket at the back of A2 WiFi Access Point/Bridge

2. Fix A2 WiFi Access Point/Bridge relevant the real situation

(a) Fix the mounting bracket on the pole using hose clamps.

Figure 2-4 A2 main unit on the mounting bracket

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

Figure 2-5 Mount the bracket on the pole

(b) Fasten A2 main unit on the wall with the mounting bracket and bolt

Figure 2-6 Mount the bracket on the wall

Altai A2 WiFI Access Point/Bridge Installation Guide

TPS13-002_rev1.0

1. (A2 AP Mode) Install a pair of omni-directional antennas to A2 WiFi Access

Point/Bridge RF ports, and properly seal the connections with waterproof

sealing tape. A typical waterproof sealing tape is shown in 错误!未找到引用

源。8.

2. Connect Ethernet cables

An Ethernet cable must be connected between the A2 Ethernet port

and the Power over Ethernet (PoE) Output port. The PoE AC Adapter

supplies the power to A2.

Another Ethernet cable (RJ –45 Straight Cable) must be connected

between the PoE Input Port and the computer or backhaul link.

PoE Port

Connect to

Input

Backhaul link, computer or peripherals

Output

A2 Ethernet port

Table 2-1 Summary of PoE connections

Figure 2-7 Connections of the PoE

Andere Handbücher für A2

Inhaltsverzeichnis

Andere ALTAI Drahtloser Zugangspunkt Handbücher

ALTAI

ALTAI A175FD Bedienungsanleitung

ALTAI

ALTAI A2 Merkblatt

ALTAI

ALTAI C260 Bedienungsanleitung

ALTAI

ALTAI C2s Bedienungsanleitung

ALTAI

ALTAI A3-Ei Bedienungsanleitung

ALTAI

ALTAI CX200 Bedienungsanleitung

ALTAI

ALTAI A3 Series Bedienungsanleitung

ALTAI

ALTAI AX500 Series Bedienungsanleitung

ALTAI

ALTAI IX500 Bedienungsanleitung

ALTAI

ALTAI A2N Merkblatt

ALTAI

ALTAI C2s Bedienungsanleitung

ALTAI

ALTAI A2C Bedienungsanleitung

ALTAI

ALTAI CX200 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung