ALTAI A2C Bedienungsanleitung

Quick Setup Guide

Altai A2c Indoor Dual-

Band 2x2 802.11ac AP

_________________________________________________

Quick Setup Guide

Version 1.0

Quick Setup Guide

Introduction

Thank you for purchasing the Altai A2c. This guide provides instructions to

install the product and set it up as AP with minimal effort.

Package Contents

T-Rail Mounting Kit

A2c Main Unit

Quick Setup

Guide

PoE Injector

(Optional Item)

Ceiling Mounting Kit

15/16in T-Rail Clip x 2

9/16in T-Rail Clip x 2

Spacer x 2

P2.6*10 Screw x 2

P2.6*25 Screw x 2

Mounting Bracket x 1

Mounting Screw x 2

P3.5*32 Screw x 2

P2.6*12 Screw x 2

Quick Setup Guide

Hardware Overview

LED Panel

Ethernet Ports and Reset Button

2-3s

5-8s

Power LED

Reboot

Factory Reset

ETH/PoE IN:

It is used to connect to power source (see

the Power Options in the following section)

and provides 10/100/1000 Mbps network

interface for LAN connection.

Reset Button:

It serves two functions:

Reboot: Press and hold the Reset Button

for 2-3 seconds until the Power LED blink

once.

Factory Reset: Press and hold the Reset

Button for 5-8 seconds until the Power LED

blink twice consecutively.

Power

Solid Orange: Power on

Off: No Power

LAN (Ethernet)

Solid Blue: LAN Connected

Flashing Blue: Data

Transmitting/Receiving

Off: LAN Disconnected

2.4G/5G Radio WiFi

(AP/Repeater/Bridge Mode)

Solid Blue (2.4G) / Green (5G):

1. AP Mode on but with no Clients

Associated

2. Repeater Mode on but not

connected to AP

3. Bridge Mode on but not connected

Flashing Blue/Green: Data

Transmitting/Receiving

Off: Radio Disabled

Solid Blue: Remote Management Mode

Off: Standalone Mode

Operation Mode

ETH/PoE IN

Reset Button

Quick Setup Guide

P2.6*10 Screw

Clip

Wall

Mounting Screw

Mounting Bracket

P2.6*12 Screw

P3.5*32 Screw

Mounting Options

Option 1: Ceiling Mount –Mounting bracket

1. Attach the mounting bracket to the ceiling using the provided mounting

screws and long screws (P3.5*32).

2. Insert the provided short screws (P2.6*12) into the bottom cover of A2c.

Make sure that the screws are exposed enough to attach the mounting

bracket.

3. Install the A2c on the mounting bracket by rotating the unit clockwise

about 90 degrees to secure it in place.

Option 2: Ceiling Mount - T-Rail clips

1. Attach the small T-Rail clips to the bottom cover of A2c using the provided

short screws (P2.6*10).

If extra space is required, use the provided spacers and large T-Rail clips

with long screws (P2.6*25).

2. Line up the connected T-Rail clips with an appropriately sized rail and

press the unit onto the rail until it snaps into place.

Lock A2c by revolving

P2.6*25 Screw

Clip

Spacer

T-Rail

Clips

Quick Setup Guide

Setup Requirements and Preparation

A computer with Web Browser: Google Chrome, Mozilla Firefox, or

Microsoft Internet Explorer 8 (or above)

Two Cat 5e/6 Ethernet cables

AltaiCare account (Optional) for cloud management service

Power Options and Cable Connection Instructions

You can follow one of the options below for A2c configuration as described

in the following sections.

1. Connect A2c Ethernet port to a PoE

Injector’s “PoE” port with an Ethernet

Cable.

2. Connect a computer to the PoE

Injector’s “LAN” port with another

Ethernet Cable.

3. Connect the PoE Injector to AC

power socket using a power cord

(Not provided in the package).

4. Make sure the Power LED light is

orange and the LAN LED light is blue.

1. Connect A2c Ethernet port to an

802.3at PoE Switch with an Ethernet

Cable.

2. Connect a computer to the switch.

3. Make sure the Power LED light is

orange and the LAN LED light is blue.

Option 2: PoE Injector (Ordered separately)

Option 1: 802.3at-compliant PoE switch

PoE

LAN

802.3at –Compliant

PoE Switch

Quick Setup Guide

1. Change TCP/IP Setting on your computer

For Windows 7 users,

1. Go to Control Panel, click Network and Sharing Center and then choose

the adapter that you want to connect to A2c unit. In this example,

adapter “Local Area Connection 2” is in connection with A2c. Click it and

then click Properties.

2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in

the list box “This connection uses the following items”, and then click

Properties.

3. Type in the following IP address and Subnet mask:

IP address: 192.168.1.2

Subnet mask: 255.255.255.0

4. Click OK to close the Internet Protocol Version 4 (TCP/IP) Properties dialog

box and click OK again to close the Local Area Connection Properties

dialog box.

Quick Setup Guide

2. Access to Web Interface

1. Open a web browser. Type 192.168.1.222 in the address bar and then hit

Enter.

2. Login page will come up and you are required to enter username and

password. By default, the credentials are:

Username: admin

Password: admin

3. Click Login.

Quick Setup Guide

3. Configure AP Mode (2.4G/5G)

Network Scenario

1. Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General.

Below screenshots show an example for 2.4G radio configuration only.

Same procedures can be applied to 5G radio configuration.

2. Make sure the box of Enable Radio is checked. Select AP mode for the

field of Radio Mode. Then click Submit.

3. Click WLAN and click More… in Detail of WLAN 0 to go to another page

for SSID and security configuration.

Internet

ISP

Modem

A2c (AP Mode)

Ethernet

Cable

2.4G + 5G

Coverage

Gateway/Router

Ethernet

Cable

Modem

Cable

Quick Setup Guide

4. Make sure WLAN is enabled by checking the box. Type in SSID to name

the wireless network you want to broadcast and then click Submit.

5. Click the tab WLAN Security. Select WPA2-PSK from the drop down menu

of Authentication Mode and select AES for Cipher Mode. Type in a

password within 8~64 characters or numbers in Pass Phrase and click

Submit.

6. Click Save & Apply at the top right corner to have all changes take effect.

7. Hook up the A2c as shown in Network

Scenario. The SSID should now be broadcast

from A2c and can be seen in the computer

for wireless connection.

Quick Setup Guide

4. Configure Gateway Mode (Router Mode)

Network Scenario

1. Follow the steps 1 –6 in Section 3 for the wireless settings.

2. Go to Configuration > Network > General.

3. Select Gateway Mode for Network Setting.

4. Select one of the following ways for Internet Connection Type. If you are

not sure about the connection options, consult your ISP for correct

settings.

(a) Static

Enter IP Address, Subnet

Mask, Default Gateway and

DNS Server IP Address as

provided by ISP.

Internet

ISP

Modem

A2c

(Gateway/Router Mode)

Ethernet

Cable

2.4G + 5G

Coverage

Modem

Cable

Inhaltsverzeichnis

Andere ALTAI Drahtloser Zugangspunkt Handbücher

ALTAI

ALTAI AX500 Series Bedienungsanleitung

ALTAI

ALTAI A3 Series Bedienungsanleitung

ALTAI

ALTAI C2s Bedienungsanleitung

ALTAI

ALTAI A2 Merkblatt

ALTAI

ALTAI CX200 Bedienungsanleitung

ALTAI

ALTAI A2 Bedienungsanleitung

ALTAI

ALTAI C260 Bedienungsanleitung

ALTAI

ALTAI A175FD Bedienungsanleitung

ALTAI

ALTAI IX500 Bedienungsanleitung

ALTAI

ALTAI A3-Ei Bedienungsanleitung

ALTAI

ALTAI CX200 Bedienungsanleitung

ALTAI

ALTAI A2N Merkblatt

ALTAI

ALTAI C2s Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung