Altec Lansing 515-8HHP LF SPEAKER Bedienungsanleitung

FREQUENCY RESPONSE 1, 2

40 Hz – 5 kHz

HIGHEST RECOMMENDED CROSSOVER FREQUENCY

2.5 kHz

SENSITIVITY 3

104 dB SPL

POWER HANDLING 4

200 W continuous; 800 W peak

MAXIMUM OUTPUT (1 m) 5

133 dB SPL

TRANSDUCER COMPONENTS

LF: 1 x 15 inch, high efficiency, low frequency driver

IMPEDANCE 7

Nominal: 8.0 Ohms or 16 Ohms

Minimum: 7.9 Ohms or 15.8 Ohms at 600 Hz

HARMONIC DISTORTION 8

THD: 0.85%

INPUT CONNECTIONS

1 x 2 position barrier strip with 0.250 in.

blade type terminals

FINISH

Dark gray enamel

REPLACEMENT LF CONE KIT

R515-8HP or R515-16HP

DIMENSIONS

Outside Diameter: 16.0 in. (406 mm)

Depth: 6.69 in. (170 mm)

Mounting Information

Bolt Circle Diameter: 15.0 in. (381 mm)

Cut-Out Diameter

Front Mount: 14.125 in. (359 mm)

Rear Mount: 14.00 in (356 mm)

WEIGHT

Net: 30.0 lbs. (13.6 kg)

Shipping: 32.0 lbs. (14.5 kg)

THEILE-SMALL PARAMETERS

fs37 Hz

Vas 342.6 liters (12.1 ft.3)

Qts 0.187

Qes 0.195

Qms 4.5

Vd258.9 cm3(15.8 in.3)

η08.6%

515-8HHP

515-16HHP

High Efficiency

15” Low Frequency Speaker

FEATURES - THE ALTEC LANSING DIFFERENCE

• Superior Efficiency

• Accurate Low Frequency Reproduction

• High Fidelity 15" / 381 mm Low Frequency Loudspeaker

• High Performance 200W AES / 800W Peak Power Handling

GENERAL PRODUCT DESCRIPTION

Since the introduction of the Voice of the Theatre®

loudspeaker

system in 1945, Altec Lansing’s 515 series have been the leading

low frequency loudspeakers in cinemas and auditoriums all over

the world. The 515 is truly legendary, and Altec Lansing’s 515-

8HHP and 515-16HHP are the two newest models in this series.

Continuing in the tradition of the 515 series, these two new

models produce the outstanding fidelity that established Altec

Lansing as the number one choice in theater, auditorium, and

studio applications.

The 515-8HHP and 515-16HHP are constructed from one of the

industry’s largest magnet structures mated to a very lightweight

cone assembly, resulting in two of the most efficient low

frequency loudspeakers that Altec Lansing has ever produced.

Both low frequency loudspeakers incorporate a high-power

handling, edge-wound aluminum, flat-wire voice-coil, which is

designed for dependability and high acoustic output level

capability. These low frequency loudspeakers also feature a

special cloth suspension, which provides extended low frequency

response and extremely high linearity. The new 515-HHP series

loudspeakers are designed to maximize the performance of bass

horn enclosures (vented or sealed).

The 515-16HHP is rated at a nominal 16 ohm impedance, making

it the first choice for dual-loudspeaker, vented bass horn

cabinets, like the Altec Lansing 210/211 and 817A enclosures.

Installation of these low frequency loudspeakers is made simple

with 0.25-inch blade type wire terminals, allowing either solder

connections or crimp type quick-connect wire terminals.

The Altec Lansing models 515-8HHP and 515-16HHP are perfect

complements to our high frequency compression drivers when

the requirements are superior efficiency, excellent low frequency

response, premium sound quality, high acoustic output level, and

absolute reliability.

PROFESSIONAl

1000 W. Wilshire Blvd., Suite 362 • Oklahoma City, Oklahoma 73116 • Phone: 1-405-848-3108 • Fax: 1-405-848-3217 • www.altecpro.com

ARCHITECTS & ENGINEERS SPECIFICATION

The loudspeakers shall be multi-purpose, 15 inch / 381 mm

low frequency cone drivers. The loudspeakers shall have an

operating bandwidth of 40 Hz to 5kHz with a sensitivity

of 104 dB when measured at a distance of one meter.

Their power handling capability shall be 200 watts AES

(800 W peak). Their nominal impedance shall be 8 Ohms

and 16 Ohms, with a minimum impedance of 7.9 Ohms

and 15.8 Ohms at 600 Hz. The magnetic gap of these

drivers shall have a flux density of 1.5 T, resulting from an

8.25 lbs. (3.74 kg) ferrite magnet. Their nominal free-air

cone resonance shall be 37 Hz and their voice-coil shall be

3 inches (76 mm) in diameter of edge-wound aluminum

ribbon. The loudspeakers shall have dimensions of 16

inches (406 mm) in diameter and 6.69 inches (170 mm) in

depth, and shall weigh 30 lbs. (13.6 kg). The low frequency

loudspeakers shall be Altec Lansing models 515-8HHP and

515-16HHP.

FREQUENCY RESPONSE AND IMPEDANCE MAGNITUDE OF 515-16HHP IN 828G

As we are continually striving to improve Altec Lansing products, specifications are subject to change without notice.

Please visit www.altecpro.com for the latest information on Altec Lansing Professional products.

1 The frequency response of the loudspeaker system is measured at a distance of no less than 3 meters to obtain full range data. The level is then corrected to be

equivalent to a 2.83 V 1 m measurement. A near field measurement of the loudspeaker system is performed for frequencies below 500 Hz. This data is then

combined with the full range measurement to give an accurate composite frequency response curve.

2 The limits of the frequency response are referenced to -10 dB of the systems rated sensitivity in a 828G vented enclosure.

3 The sensitivity of the loudspeaker system is the log based average SPL taken over the intended bandwidth of operation for the system with a 2.83 V swept sine

stimulus. The data is measured and level corrected in a manner consistent with notes 1 and 2.

4 The power handling capacity of the loudspeaker system is tested using a full range form of AES Standard 2-1984. The test stimulus is band limited (40 Hz – 16

kHz) pink noise with a 6 dB crest factor. The applied RMS voltage is determined using the minimum impedance of the system. The amplifier used to drive the

system has a minimum operating headroom of 6 dB referenced to the RMS voltage.

5 The peak output level of the loudspeaker system is calculated based on the sensitivity and the peak power handling capabilities of the system.

6 The minimum impedance of the loudspeaker system is taken over its intended band of operation.

7 The distortion measurements of the loudspeaker system are performed at a distance of 1 m with RMS input voltages corresponding to 1% of rated system power

handling calculated using minimum system impedance. The distortion percentages are log based averages from 300 Hz – 3 kHz.

VISIT WWW.ALTECPRO.COM FOR

• Authorized EASE data on all Altec Lansing Professional loudspeakers

• Specification sheets in .pdf format. Download page 1 of the specification sheet for you submittals.

• One paragraph A&E Specifications in .doc format

SPECIFICATION NOTES

AW1074 REV02

1000 W. Wilshire Blvd., Suite 362

Oklahoma City, Oklahoma 73116

Phone: 1-405-848-3108 • Fax: 1-405-848-3217

Web: www.altecpro.com • Email: [email protected]

PROFESSIONAl

Dieses Handbuch passt für folgende Modelle

Andere Altec Lansing Sprecher Handbücher

Altec Lansing

Altec Lansing INMOTION IMT207 Installationsanleitung

Altec Lansing

Altec Lansing 3182 LF SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing 515-8LFE LF SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing T612 - QUICK CONNECT CARD Montageanleitung

Altec Lansing

Altec Lansing AL-SND325F Bedienungsanleitung

Altec Lansing

Altec Lansing ADA310W Bedienungsanleitung

Altec Lansing

Altec Lansing 209 CEILING SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing 909-16A HF DRIVERS Benutzerhandbuch

Altec Lansing

Altec Lansing 299-16A HF DRIVER Bedienungsanleitung

Altec Lansing

Altec Lansing 3127 LF SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing EXPRESSIONIST CLASSIC - Montageanleitung

Altec Lansing

Altec Lansing 401B CEILING SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing PS-90 SPEAKER SYSTEM Bedienungsanleitung

Altec Lansing

Altec Lansing inMotion SoundBlade Bedienungsanleitung

Altec Lansing

Altec Lansing IML 237 Bedienungsanleitung

Altec Lansing

Altec Lansing SHOCKWAVE 100 Bedienungsanleitung

Altec Lansing

Altec Lansing 416-8C LF SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing IMT7012 Bedienungsanleitung

Altec Lansing

Altec Lansing IMT802 Bedienungsanleitung

Altec Lansing

Altec Lansing 220 Bedienungsanleitung

Altec Lansing

Altec Lansing 309 Series Bedienungsanleitung

Altec Lansing

Altec Lansing VS2120 Bedienungsanleitung

Altec Lansing

Altec Lansing 808-16A HF DRIVERS Bedienungsanleitung

Altec Lansing

Altec Lansing 902-16B HF DRIVERS Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung