Altinex SW104-130 Bedienungsanleitung

SWITCHER

MANUAL PART NUMBER: 400-0426-

006

2-IN VIDEO+ AUDIO TO

TWISTED PAIR (TP) OUTPUT,

AUTO-SWITCHER/TRANSMITTER

USER’S GUIDE

SW104-130

SWITCHER

400-0426-006 1

TABLE OF CONTENTS

Page

PRECAUTIONS / SAFETY WARNINGS................ 2

GENERAL..........................................................2

INSTALLATION..................................................2

CLEANING.........................................................2

FCC NOTICE .....................................................2

ABOUT YOUR SW104-130...................................... 3

TECHNICAL SPECIFICATIONS.............................. 3

PRODUCT DESCRIPTION ...................................... 5

APPLICATION DIAGRAMS...................................... 5

DIAGRAM1: TYPICAL SETUP ..........................5

DIAGRAM2: INTERNAL VIEW..........................6

INSTALLING YOUR SW104-130........................... 7

OPERATION............................................................... 7

VIDEO EQUALIZATION.....................................7

SWITCH MODES...............................................7

TROUBLESHOOTING GUIDE................................. 8

LEDS ARE OFF..................................................8

UNIT DOES NOT AUTO-SWITCH......................8

NO DISPLAY......................................................8

ALTINEX POLICIES.................................................. 9

LIMITEDWARRANTY/RETURN POLICIES.......9

CONTACT INFORMATION................................9

SWITCHER

400-0426-006 2

PRECAUTIONS / SAFETY WARNINGS 1

Please read this manual carefully before using your

SW104-130 Switcher. Keep this manual handy for

future reference. These safety instructions are to

ensure the long life of your SW104-130 and to

prevent fire and shock hazards. Please read them

carefully and heed all warnings.

1.1 GENERAL

•Unauthorized personnel shall not open the unit

since there are high-voltage components inside.

•Qualified ALTINEX service personnel or its

authorized representative must perform all

service.

1.3 INSTALLATION

•For best results, place the SW104-130 on a flat,

level surface in a dry area away from dust and

moisture.

•To prevent fire or shock, do not expose this unit

to water or moisture. Do not place the

SW104-130 in direct sunlight, near heaters or

heat-radiating appliances, or near any liquid.

Exposure to direct sunlight, smoke, or steam can

harm internal components.

•Handle the SW104-130 Switcher carefully as

dropping or jarring can damage internal

components.

•Do not place heavy objects on top of the

SW104-130.

•To turn off the main power, be sure to remove

the cord from the power outlet. The power outlet

should be installed as near to the equipment as

possible, and should be easily accessible.

•Do not pull the power cord or any cable that is

attached to the SW104-130.

•If the SW104-130 is not used for an extended

period, disconnect the power cord from the

power outlet.

1.4 CLEANING

•Unplug the SW104-130 power cord before

cleaning. Clean surfaces with a dry cloth. Never

use strong detergents or solvents such as

alcohol or thinner. Do not use a wet cloth or

water to clean the unit.

1.5 FCC NOTICE

•This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

•This equipment has been tested and found to

comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions found herein, may cause harmful

interference to radio communications. Operation

of this equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the interference

at his own expense.

•Any changes or modifications to the unit not

expressly approved by ALTINEX, Inc. could void

the user’s authority to operate the equipment.

SWITCHER

400-0426-006 3

ABOUT YOUR SW104-130 2

SW104-130

2-In Video+ Audio to TP Output,

Auto-Switcher/Transmitter

with Local Output

The SW104-130 Auto-Switcher is designed to

switch between two video+ audio sources. The

selected source is converted and transmitted using

ALTINEX’s Twisted Pair standard as well as

buffered and output locally. The SW104-130 is

designed for use with an equivalent ALTINEX TP

Receiver such as the TP115-111.

The SW104-130 features three modes of operation:

auto, manual,and remote. In auto mode, Input 2is

the default selection and the SW104-130

automatically switches to Input 1on signal

detection. In manual mode, the input is selected

using a switch on the side of the unit. Remote

switching is made via a contact closure connected

to the Input Select jack. The contact may be

controlled manually, or by using a control system.

The unit is encased in a solid metal enclosure and

ships with an external power adapter. The

SW104-130 is perfect for applications that use wall

or floor plates for auto-switching. The SW104-130

may be mounted to furniture or other suitable

surfaces using optional hardware.

The latest generation of Twisted Pair devices uses

an innovative, patented technology* developed by

ALTINEX. The new signal processing technology

allows transmitting and receiving fully equalized

computer video signals, stereo, and audio signals

over long distances.

TECHNICAL SPECIFICATIONS 3

Specifications are subject to change.

See www.altinex.com for up-to-date information.

FEATURES/

DESCRIPTION SW104-130

Inputs

Video 15-pin HD female (2)

Audio 3.5 mm female (2)

Contact Closure 2.5mm DC power jack (1)

Power 2.5mm DC power jack (1)

Outputs

Local Video 15-pin HD female (1)

Local Audio 3.5 mm female (1)

CAT-5/6 Twisted Pair RJ-45 female (1)

Compatibility

Signal Types ALTINEX Standard for

Twisted Pair

Video Signal

Resolutions VGA through UXGA

480p through 1080i

Recommended Max.

Cable Lengths

Note: Measurements

made using ALTINEX

low-skew cable,

CB3150PV.

VGA: 640x480@60Hz

900 ft (274 m)

XGA: 1024x768@60Hz

700 ft (213 m)

SXGA: 1280x1024@60Hz

650 ft (198 m)

UXGA: 1600x1200@60Hz

600 ft (183 m)

Accessories Included

Power Adapter +9 VDC, 1.1 A

Table 1. SW104-130 General

* US Patent 7,065,190

SWITCHER

400-0426-006 4

MECHANICALSW104-130

Material 0.091 in Al

Finish Black

Height 0.960in (24 mm)

Width 4.300 in (109 mm)

Depth 5.200in (132 mm)

Weight 1.00lb (0.45 kg)

T°Operating 10°C-35°C

T°Maximum 50°C

Humidity 90%non-condensing

MTBF (calculations) 40,000 hrs (min.)

Table 2. SW104-130 Mechanical

ELECTRICALSW104-130

Video Input Signal

Video Signal 1.5 Vp-p max

Video Impedance 75 ohms

SYNC Signal TTL (+/-)

SYNC Impedance 10 kohms

Audio Input Signal

Impedance 10 kohms

Level 0.9 Vp-p max

Twisted Pair Output

CAT-5/6 Twisted Pair Video/Sync/Audio Signals

ALTINEX Standard

Local Video Output

Video Gain 0dB

Video Impedance 75 ohms

Sync Signal TTL (+/-)

Video ResolutionsVGA through UXGA,

480p through 1080i

Local Audio Output

Impedance 1 kohm

Local Gain 0dB

Power Consumption

External Adapter: 9 VDC 450 mA (4W max.)

Table 3. SW104-130 Electrical

SWITCHER

400-0426-006 5

PRODUCT DESCRIPTION 4

APPLICATION DIAGRAMS 5

DIAGRAM 1: TYPICAL SETUP

MONITOR

OUTPUT

VIDEO

CONTACT

CONTROL

OUTPUT

POWER

COMPONENT

INPUT1

AUDIO

INPUT1

INPUT2

AUDIO

LOCAL

AUDIO LOCAL

4TP MAIN

EQUALIZATION

SWITCH

CLOSURE

COMPUTER/

COMPONENT

INPUT2

VIDEO

SW104-130

TP115-111

SWITCHER

400-0426-006 6

DIAGRAM 2: INTERNAL VIEW

SW 104-130

CONTROL

CH2

CH1

POWER

CONTROL

SWITCH

PLUG AND PLAY

HOR

VER

H/W

VER

HOR

RED

BLUE

GREEN

CONTROL

PAIR 4

RIGHT

LEFT

RIGHT

LEFT

RED

BLUE

GREEN

PAIR 2

PAIR 3

PAIR 1

RED

BLUE

GREEN

VER

HOR

PLUG AND PLAY

POWER

2.5 mm

9V,1A

COMPUTER/

COMPONENT

15-PIN HD

AUDIO STEREO

3.5 mm

(VIDEO 1)

AUDIO STEREO

3.5 mm

(VIDEO 2)

LOCAL MONITOR

COMPUTER/

COMPONENT

OUTPUT

TWISTED PAIR

RJ-45

LOCAL

3.5 mm

AUDIO MONO

SYNC

PROCESSING

CONTACT

CLOSURE

VIDEO INPUT1

COMPONENT

COMPUTER/

VIDEO INPUT2

15-PIN HD

SWITCHER

400-0426-006 7

INSTALLING YOUR SW104-130 6

Step 1. Make sure to use the ALTINEX power

adapter supplied with the unit. Connect

the power adapter to the power port. The

Power and Input 2 LEDs should turn on.

NOTE: Input 2 is the default if there is no

signal on Input 1and the Control

Switch is in the Auto position.

Step 2. Connect a video and audio source to

Input 1. If there is a properly formatted

input signal on Input 1, the switcher will

switch to Input 1 automatically, and the

Input 1 LED will turn on.

Step 3. Connect a video and audio source to

Input 2. If there is a properly formatted

input signal on Input 1, the switcher will

remain on Input 1.

Step 4. Connect the local video and audio outputs

to the local monitor and speakers.

Step 5. If a remote switch is to be used, connect

the control cable to the Input Select port.

See Section 7 for operation control.

Step 6. Verify that the picture quality on the

display is good. If a signal is not being

received, make sure that the display is

compatible with the resolution of the

computer graphics card.

Step 7.Connect the 4TP Main Output to the input

of the Twisted Pair receiver.

NOTE: Connect the Twisted Pair

receiver per its instructions.

Step 8. The SW104-130 is now ready for

operation. Depending on the length of the

cable, the video equalization adjustment

may need to be adjusted for optimal

performance.

OPERATION 7

The SW104-130 requires only one adjustment to be

made for optimal performance. The adjustment is

video equalization for long cable lengths. The

remaining controls are for input selection only.

7.1 VIDEO EQUALIZATION

Video equalization is provided to fine-tune the

displayed image on the remote display. The

equalization adjustments on the SW104-130

and Twisted Pair receiver work together.

Start by setting both units to minimum and then

increase slowly. Some monitors respond very

quickly to changes in the equalization, others

may not display an image until the equalization

is set precisely.

7.2 SWITCH MODES

7.1.1 AUTO-SWITCH MODE

In auto-switch mode, the SW104-130 automatically

selectsInput 2 if no active signal is present on

Input 1. If a signal is on Input 2 and not on Input 1,

the SW104-130 will maintain Input 2. However,

when an active signal is applied to Input 1, the

SW104-130 will switch to Input 1. If active signals

are on both inputs, the SW104-130 will

automatically switch to Input 1.

7.1.2 MANUAL-SWITCH MODE

The SW104-130 control switch allows switching

between Input 1 and Input 2. Placing the control

switch in either the Input 1 or Input 2 position forces

the source signal to the main and local outputs

thereby disabling auto-switching.

7.1.3 REMOTE SWITCH MODE

Remote switching is achieved via a contact closure

on the Input Select jack. Remote switching mode

disables both auto-switching and the Control Switch

position. A closed contact selects Input 1 and an

open contact selects Input 2.

SWITCHER

400-0426-006 8

TROUBLESHOOTING GUIDE 8

We have carefully tested and found no problems in

the supplied SW104-130 unit. However, we would

like to offer the following suggestions:

8.1 LEDs ARE OFF

Cause 1: The power adapter is installed

wrong.

Solution 1: Make sure the adapter output is

connected to the power input jack on

the unit. If one of the LEDs is still not

on, see Solution 2.

Solution 2: Ensure the adapter is plugged into

an AC outlet that has power. If the

adapter has AC power and the LEDs

are still off, see Cause 2.

Cause 2: The wrong power adapter is

installed.

Solution 1: Please use the ALTINEX supplied

external adapter. If one of the LEDs

is still not on, please call ALTINEX

at (714) 990-2300.

8.2 UNIT DOES NOT AUTO-SWITCH

Cause 1: The remote override switch is

installed.

Solution: Remove the connection to the Input

Select jack on the unit. If a plug is in

the jack, even without a switch

connected, the SW104-130 will not

auto-switch properly. If the unit does

not auto-switch with the plug

removed, see Cause 2.

Cause 2: The control switch is not in the

auto position.

Solution: Switch the Control Switch to the

auto position. If the unit does not

auto-switch, see Cause 3.

Cause 3: The signal is not active or is

improperly formatted.

Solution 1: Remove the input signals from the

switcher. If the Input 2 LED is off,

call ALTINEX at (714) 990-2300. If

the Input 2 LED is on, see

Solution 2.

Solution 2: Connect a properly formatted video

type signal to Input 1. If the switcher

does not switch to Input 1, see

Solution 3.

Solution 3: Bypass the switcher and connect the

output of the source directly to the

display. If the display is good, then

see Cause 4.

Cause 4: The wrong power adapter is

installed.

Solution 1: Please use the ALTINEX-supplied

external adapter. If the unit still does

not auto-switch, please call

ALTINEX at (714) 990-2300.

8.3 NO DISPLAY

Cause 1: The source has a problem.

Solution: Check the source and make sure

that there is a signal present and all

source connections are correct. If

the source is working and there is

still no display, see Cause 2.

Cause 2: Manual override is ON.

Solution: Make sure there is nothing

connected to the Input Select port

on the switcher. If there is nothing

connected, see Cause 3.

SWITCHER

400-0426-006 9

Cause 3: Signal is bad or missing.

Solution 1: Make sure the switcher output is

connected to the monitor. If there is

still no display, see Solution 2.

Solution 2: Remove both inputs to the switcher

and connect the active signal from

the source to Input 2. If there is still

no display, see Solution 3.

Solution 3: Bypass the switcher and connect the

output of the source directly to the

monitor. If the display is good, then

call ALTINEX at (714) 990-2300. If

there is still no display, see Cause 4.

Cause 4: Cable connections are incorrect.

Solution: Make sure the cables are properly

connected. Also, make sure that the

continuity and wiring are good. If

there is still no display present, see

Cause 5.

Cause 5: The display has a problem.

Solution: Make sure the display is powered

and is turned on. If there is still no

display, please call ALTINEX at

(714) 990-2300.

ALTINEX POLICIES 9

9.1 LIMITED WARRANTY/RETURN POLICIES

Please see the ALTINEX website at

www.altinex.com for details on warranty and

return policies.

9.2 CONTACT INFORMATION

ALTINEX, Inc.

592 Apollo Street

Brea, CA 92821 USA

TEL: 714 990-2300

TOLL FREE:1-800-ALTINEX

WEB: www.altinex.com

E-MAIL: [email protected]

Inhaltsverzeichnis

Andere Altinex Schalten Handbücher

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex MX2406RM Bedienungsanleitung

Altinex

Altinex MX2456RM Bedienungsanleitung

Altinex

Altinex Universal Tilt 'N Plug Interconnect Box... Bedienungsanleitung

Altinex

Altinex MX2414RM Bedienungsanleitung

Altinex

Altinex MX2216RM Bedienungsanleitung

Altinex

Altinex MX2426CV Bedienungsanleitung

Altinex

Altinex UT260-041 Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-107 Bedienungsanleitung

Altinex

Altinex DA1916SX Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-108 Bedienungsanleitung

Altinex

Altinex MX2206RM Bedienungsanleitung

Altinex

Altinex MX2214RM Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-102 Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex Tilt 'N Plug Interconnect Box TNP100-HB Bedienungsanleitung

Altinex

Altinex UT260-102 Bedienungsanleitung

Altinex

Altinex Furniture Mount Interconnect Box... Bedienungsanleitung

Altinex

Altinex MX2456RM Bedienungsanleitung

Altinex

Altinex MT105-8X8 Bedienungsanleitung

Altinex

Altinex MX2436RM Bedienungsanleitung

Altinex

Altinex MULTITASKER MT109-100 Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung