Altinex MULTI-TASKER MT104-107 Bedienungsanleitung

MULTI-TASKER

MANUAL PART NUMBER: 400-0176-002

3-IN, 1-OUT DUAL VIDEO/S-VIDEO

SWITCHER CARD FOR MULTI-TASKER

USER’S GUIDE

MT104-107

MULTI-TASKER

TABLE OF CONTENTS

Page

PRECAUTIONS / SAFETY WARNINGS.................. 2

1.1 GENERAL ..................................................... 2

1.2 INSTALLATION............................................. 2

1.3 CLEANING.................................................... 2

1.4 FCC / CE NOTICE......................................... 2

ABOUT YOUR MULTI-TASKER™........................... 3

TECHNICAL SPECIFICATION ................................ 3

PRODUCT DESCRIPTION...................................... 4

APPLICATION DIAGRAM........................................ 5

APPLICATION 1....................................................... 5

APPLICATION 2: INTERNAL VIEW ............................. 6

INSTALLING YOUR MULTI-TASKER™.................. 7

OPERATION............................................................ 7

7.1 RS-232 CONTROL........................................ 7

7.2 DESCRIPTION OF COMMANDS.................. 7

7.3 SUMMARY OF COMMANDS....................... 11

TROUBLESHOOTING GUIDE............................... 12

8.1 LED IS NOT LIT .......................................... 12

8.2 NO DISPLAY............................................... 12

ALTINEX POLICY.................................................. 12

9.1 LIMITED WARRANTY/RETURN POLICY ... 12

9.2 CONTACT INFORMATION.......................... 12

MULTI-TASKER

PRECAUTIONS / SAFETY WARNINGS 1

Please read this manual carefully before using

your MT104-107. Keep this manual handy for

future reference. These safety instructions are to

ensure the long life of your MT104-107 and to

prevent fire and shock hazard. Please read them

carefully and heed all warnings.

1.1 GENERAL

•Qualified ALTINEX service personnel, or their

authorized representatives must perform all

service.

1.2 INSTALLATION

•To prevent fire or shock, do not expose this unit

to rain or moisture. Do not place the MT104-107

in direct sunlight, near heaters or heat radiating

appliances, or near any liquid. Exposure to

direct sunlight, smoke, or steam can harm

internal components.

•Do not pull the cables that are attached to the

MT104-107.

•Insert the card carefully into the slots of the

Multi-Tasker™ without bending any edges.

•When removing a card, please make sure that

the card to which it is attached is also pulled out

simultaneously.

1.3 CLEANING

•Clean only the connector area with a dry cloth.

Never use strong detergents or solvents, such

as alcohol or thinner. Do not use a wet cloth or

water to clean the card. Do not clean or touch

any component or PCB.

1.4 FCC / CE NOTICE

•This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

•This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when

the equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications. Operation

of this equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the interference

at his own expense.

•Any changes or modifications to the unit not

expressly approved by ALTINEX, Inc. could void

the user’s authority to operate the equipment.

MULTI-TASKER

ABOUT YOUR MULTI-TASKER™ 2

MT104-107

3-IN 1-OUT, Dual Video/S-Video

Switcher Card

The MT104-107 is a dual 3-IN 1-OUT

Video/S-Video Switcher Card. There are 3 inputs

(+1internal) for Video and 3 inputs (+1internal) for

S-Video. It is designed for use in Multi-Tasker

enclosures. The MT Video/S-Video SW card

enables composite video sources and S-Video

sources to be connected and switched to a single

display or recording device.

The MT104-107 card utilizes solid state switching

technology, and offers a video bandwidth of

350MHz. This bandwidth enables the MT104-107

to pass high-resolution video signals without

degradation. Inputs are selected via easy-to-use

ASCII commands from a control system or

computer connected to the RS-232 port of a

Multi-Tasker™ enclosure. Also available through

ASCII control is “on-off” control of individual

outputs.

TECHNICAL SPECIFICATION 3

FEATURES/

DESCRIPTION MT104-107

GENERAL

Inputs

External Input

Connectors (3) BNC Female Connectors &

(3) 4-pin Mini-DIN Connectors

Internal Input

Connectors (1) BNC Female Connector &

(1) 4-pin Mini-DIN Connector

Outputs

S-Video Output

Connectors (1) BNC Female Connector

(1) 4-pin Mini-DIN Connector

Approvals CE/FCC

Table 1. MT104-107 General

MECHANICAL MT104-107

Enclosure Slots Required One

Weight 0.43lb (0.19kg)

Shipping Weight 1 lb. (0.45kg)

Connector Panel Black

T° Operating 10°C to 40°C

T° Storage 0°C to 50°C

Humidity 90% non-condensing

MTBF (calc.) 55,000 hrs

Table 2. MT104-107 Mechanical

ELECTRICAL MT104-107

Input Signals

Analog +/-1.5V (1.5Vp-p)

Or Digital +5V

Impedance 75 Ohms

Type Differential

Return Loss -38dB @ 50MHz

Maximum DC Offset 10mV

Output Signals

Gain 1.05 (+/-5%)

Impedance 75 Ohms

Propagation Delay (Sync) 4nS max.

Rise/Fall time (Sync) 6nS max.

Differential Phase Error 01° @ 4.5 MHz

Bandwidth 350 MHz @ -3dB

Power

(from MT100-100)+6V DC (80mA)

-6V DC (60mA)

Power Consumption 1 watt max.

Optional Accessories

MS8102CA 6ft., 15-pin HD Male to

5 BNC Male

MS8112CA 6ft., 15-pin HD Female

to 5 BNC Male

Table 3. MT104-107 Electrical

MULTI-TASKER

PRODUCT DESCRIPTION 4

MULTI-TASKER

APPLICATION DIAGRAM 5

Application 1

MULTI-TASKER

Application 2: Internal View

3-IN 1-OUT VIDEO, S-VIDEO SWITCHER (BNC, 4-PIN DIN IN/OUT)

POWER

MT104-107

Inputs 1

BNC

4-PIN

MINI

DIN

S-Video

INPUT

OFF

INPUT

OFF

OUTPUT

4-PIN

MINI

DIN

OUTPUT

BNC

Inputs

C-Video

INPUT SELECT

CONTROL

MULTI-TASKER

INSTALLING YOUR MULTI-TASKER™ 6

Step 1. Slide the MT104-107 into an available

slot in the Multi-Tasker™ Enclosure in

order to connect to the bus. Make sure

that the MT104-107 card fits into place.

Secure the card to the Multi-Tasker™ by

tightening the retainer screws located on

the top and bottom of the MT104-107

card.

Step 2. The LED on the card panel will turn red

indicating that the card is in full operation.

Step 3. Connect a coaxial cable from the video

source to the input connector of the

MT104-107. Connect the output

connectors of the MT104-107 to the

display devices through a coaxial cable.

Step 4. Starting from the left, identify the slot

number where the MT104-107 card is

plugged into the Enclosure and note that

it is for RS-232 control.

OPERATION 7

7.1 RS-232 CONTROL

When used in the Multi-Tasker™ Enclosure, the

MT104-107 has many advanced remote control

capabilities, which are accessible through standard

RS-232 communication. The actual controlling can

be accomplished through a computer control

system or any other device capable of sending

RS-232 commands.

7.1.1 RS-232 INTERFACE

The RS-232 commands for the MT104-107 are

in a simple ASCII character format.

1. Square brackets “[ ]” are part of the

command.

2. Use uppercase letters for all commands.

After processing a command, an OK or ER will

be returned as feedback if "F" is included at the

end of a command string.

Commands such as [ON], [OFF], and [IO] that

end in "S" will be saved into memory.

Commands not ending in "S" will still be

executed, but will not be restored when the

system is Reset or powered OFF then ON.

7.2 DESCRIPTION OF COMMANDS

Each command consists of three parts:

Function, card ID, and unit ID. [Function,

Card ID, Unit ID]

Example:

[VERC3U2]

VER = Function

C3 = Card ID

U2 = Unit ID

For Function, see a detailed explanation under

each command description.

The Card ID is an assigned value from 1 to 19

(1 to 8 or 1 to 4 depending on which enclosure

is being used), which represents the number of

slots. Card ID 0 (C0) is used for the controller

(see user’s guide for the MT100-100).

Changing the position of a card will significantly

affect the commands recorded in software

definitions or a third party control system.

The Unit ID has a value from 0 to 9. Unit ID 0

should be used for single unit operation. If the

Unit ID is set to 0, then each command can be

used without Ui (use command [SETU0]; see

user’s guide for the MT100-100).

Example:

[VERC3]: for unit ID zero

[VERC3Ui]: for unit ID other than zero

[VERC3]: equivalent to [VERC3U0]

1. [VER]

This command receives the software version

and card type for the MT104-107 card.

Command Format: [VERCnUi]

Cn = card ID (n = # from 1 to max slots)

Ui = Unit ID (i = # from 0 to 9)

Example:

An MT104-107 card is in slot #2 of unit 3.

Retrieve the card type and version by sending

MULTI-TASKER

the command [VERC2U3]. The Multi-Tasker™

will return the following feedback:

MT104-107 690-0160-002

MT104-107 = card type

690-0160-002 = software version

2. [C]

This command receives the status of the card.

Command Format: [CnUi]

Cn = card ID (n = 1 to max slots)

Ui = unit id (i = from 0 to 9)

Example:

There is an MT104-107 card is in slot #2 of

unit 3. S-Video Input 1 is ON and C-Video

Input 3 is ON. To get the status of the card,

send the command [C2U3]. The feedback will

be as follows:

ON: 1-SVID 3-CVID

1-SVID = S-Video Input 1 ON

3-CVID = Composite Video Input 3 ON

If there is no card in slot #2 of unit 3, sending

the [C2U3] command will not return any

feedback.

3. [CnS]

This command saves the current status of the

card's input to output configuration. This

configuration will be restored after the system is

Reset or powered OFF then ON.

Cn = card number

S = save configuration

If S-Video Outputs 1,2,3 and Video Outputs

1,2,3 are enabled, the feedback after sending

the command [C4S], for slot 4, would be:

SVID: 1,2,3 CVID: 1,2,3 C04 Saved

4. [ON]

This command enables one input of a single

card or a group of cards.

SINGLE CARD

[ONmVCnUiS] for Composite Video

[ONmSCnUiS] for S-Video

This command enables input “m” and disables

all other inputs.

[ONmVCnUi]: Enables one composite video

input (C-Video)

[ONmSCnUi]: Enables one S-Video input

Default when plugged in:

S-Video Input #1 = ON

C-Video Input #1 = ON

m = Input number (m = 1 to 4)

(input 4 is internal)

Cn = Card ID (n = # from 1 to max slots)

Ui = Unit ID number (i = 0 to 9)

S = activates S-Video input

V = activates C-Video input

S = saves command to memory

Example:

All of the inputs on the MT104-107 card are

OFF and the card is in slot #5 of unit 3:

1) [ON1VC5U3]: Turns ON C-Video input 1.

2) [ON3VC5U3]: Turns ON C-Video input 3

Since only one of each input type may be

selected at a time, Input 1 is now OFF. It

was turned OFF automatically when Input 3

was turned ON.

3) [ON2SC5U3]: Turns ON S-Video input 2.

GROUP OF CARDS

[ONmVGkUiS] for Composite Video

[ONmSGkUiS] for S-Video

This command enables input "m" for each card

in group "k" of unit "i".

[ONmVGkUi]: Enables a group of composite

video inputs (C-Video)

[ONmSGkUi]: Enables a group of S-Video

inputs

m = Input number (m = 1 to 4)

(input 4 is internal)

Gk = group number (k = # from 1-9)

Ui = unit number (i = # from 0-9)

S = activates S-Video input

V = activates C-Video input

MULTI-TASKER

S = saves command to memory

Example:

[ON1VG1U1]: Turns ON C-Video input 1 for

each card in group 1 of unit 1.

[ON…..P]: sets path

This command will set the path for the output,

but it is not active until the switch command,

[SW], is executed. Commands ending in "P"

are not executed immediately. The Path for

outputs may be set on a single card or for

multiple cards. In either case, all Paths will be

switched when the [SW] command is executed.

Command Formats:

[ONmVCnUiP] and

[OnmSCnUiP]

m = Input number (m = 1 to 4)

(input 4 is internal)

S = activates S-Video input

V = activates C-Video input

Cn = card ID (n = slot # from 1 to max slots)

P = path

Example:

There are two MT104-107 cards in slot 6 and 7

of unit 3. Enable S-Video input 1 of card 6 and

S-Video input 3 of card 7 simultaneously. Use

the following commands:

[ON1SC6U3P]

[ON3SC7U3P]

[SW]

If "F" is included, use the [ONmCnUiPF]

command or the [ONmCnUiFP]command.

[ON…..F]: feedback

After processing a command, an OK or ER will

be returned as feedback if "F" is included at the

end of a command string.

Example:

[ON1VC2U3F]: if path is not set

[ON1VC2U3PF]: if path is set

5. [OFF]

This command disables one input of a single

card or a group of cards.

SINGLE CARD

[OFFmVCnUiS] for Composite Video

[OFFmSCnUiS] for S-Video

This command disables input “m” or all inputs.

[OFFVC5CnUi]:Turns OFF all C-Video inputs

of the MT104-107 card.

m = Input number (m = 1 to 4)

(input 4 is internal)

Cn = Card ID (n = slot # from 1 to max slots)

Ui = Unit ID number (i = 0 to 9)

S = activates S-Video input

V = activates C-Video input

S = saves command to memory

Example:

Card 5 of unit 3 has S-Video input 1 and

C-Video input 2 ON. The following commands

can be used to turn OFF the inputs.

1) [OFF1SC5U3] or [OFFSC5U3]: Turns OFF

S-Video input.

2) [OFFVC5U3]: Turns OFF C-Video input.

GROUP OF CARDS

[OFFmVGkUiS] for Composite Video

[OFFmSGkUiS] for S-Video

This command disables input "m" for each card

in group "k" of unit "i".

m = Input number (m = 1 to 4)

(input 4 is internal)

Cn = Card ID (n = slot # from 1 to max slots)

Ui = Unit ID number (i = 0 to 9)

S = activates S-Video input

V = activates C-Video input

S = saves command to memory

Example:

1) [OFF1SG1U1]: Turns OFF S-Video input 1

for each card in group 1 of unit 1.

2) [OFF1VG1U1]: Turns OFF C-Video input 1

for each card in group 1 of unit 1.

Inhaltsverzeichnis

Andere Altinex Schalten Handbücher

Altinex

Altinex MX2214RM Bedienungsanleitung

Altinex

Altinex MX2226AT Bedienungsanleitung

Altinex

Altinex MT105-8X8 Bedienungsanleitung

Altinex

Altinex SW104-130 Bedienungsanleitung

Altinex

Altinex DA1916SX Bedienungsanleitung

Altinex

Altinex Furniture Mount Interconnect Box... Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-108 Bedienungsanleitung

Altinex

Altinex MX2456RM Bedienungsanleitung

Altinex

Altinex MX2222AT Bedienungsanleitung

Altinex

Altinex MX2206RM Bedienungsanleitung

Altinex

Altinex UT260-041 Bedienungsanleitung

Altinex

Altinex MT304-203 Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex Tilt 'N Plug Interconnect Box TNP100-HB Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-102 Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex SW1956CT Bedienungsanleitung

Altinex

Altinex MT104-100/103 Bedienungsanleitung

Altinex

Altinex MX2414RM Bedienungsanleitung

Altinex

Altinex MULTITASKER MT109-100 Bedienungsanleitung

Altinex

Altinex MX2100AV Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex MX2406RM Bedienungsanleitung

Altinex

Altinex MX430-101 8x8 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung