Amadas Smart Door Lock Bedienungsanleitung

The illustrations may look different from the real product.

Images from your mobile phone screen may vary depending on

the operating system (OS) you are using.

If you have any questions, please contact us at +82 2 1522 4802

Quick User Guide

QUICK GUIDE

www.amadas.kr

P 1

1 2

3 4

5 6

Installing the Smart Lever Lock (Tubular) Step.1

Tubular

P 2

Attach the inclined face of the latch

bolt in the closing direction of the

door, and then tighten the screw.

Align the power terminal of the locking

device hole horizontally, and then insert

the outer lever module connection bolt

into the door.

Attach the fixing bolt to the inner lever,

insert the module into the lock, then

tighten the fixing bolt clockwise using a

screwdriver, for the left and right side,

respectively.

Pull thelever in thedirection of usage

(left or right) and operatethe inner

lever down to check if thelatch is

operating.

Open the cap at the end of theinner lever

and insert the batteries.

(Refer to Page 18 of the Instruction Manual)

After installing the door trim, adjust

it with a space bolt to adjust the

door shake.

1 2

3 4

Installing the Smart Lever Lock (Mortise)

P 3

Step.1

Mortise

Attach the inclined face of the latch

bolt in the closing direction of the

door, and then tighten the screw.

Align the power terminal of the locking

device hole horizontally, and then insert

the outer lever module connection bolt

into the door.

Attach the fixing bolt to the inner lever,

insert the module into the lock, then

tighten the fixing bolt clockwise using a

screwdriver, for the left and right side,

respectively.

Pull thelever in the direction of usage

(left or right) and operatetheinner

lever down to check if the latch is

operating.

Open the cap at the end of the inner lever

and insert the batteries.

(Refer to Page 18 of the Instruction Manual)

After installing the door trim, adjust

it with a space bolt to adjust the

door shake.

Function Settings

Button Functions

Beep BeepBeep

P 4

Step.2

Open Door Double Lock Access Code

Lock

Function

Settings

Outer

Side

Inner

Side

- The initial Access Code is 1234.

- The Access Code can be a minimum of 4 digits and can be up to 12 digits (digits from 0 to 5).

(If less than 4 digits or more than 12 digits are entered, the registration will be canceled with a

"beep" sound.)

- If there is no additional input within 15 seconds while entering your access code, the registration

will be canceled with a "beep" sound.

- When the registration mode is canceled, the existing Access Code is retained, and when the

new registration (changed code) is completed, the existing Access Code is deleted.

- The normal registration sound is a “ding” sound and the incorrect registration sound is a “beep” sound.

Add

Access Code

Delete

Access Code

Volume

Settings

Reset BluetoothMaster Key Settings,

Input

Press and hold the

Function Settings

Button for 3 seconds

Wait

Inner Side Outer Side

Enter the User Code,

and press

Enter the Access Code,

press

Enter the Access Code

again, and press

After pressing

the ③ button

and press

Access

P 5

Step.3

- To prevent exposureof theAccess Code,

enter false numbers before entering the

Access Code.

Ex) Falsenumbers can be used both before

and after the Access Code.

(E.g., 351234000)

Passcode Access

Use the flashlight on your cell phone to charge the solar panel

on the outer lever.

(About 60 seconds. The charging time may vary depending on the

amount and direction of the light.)

When the LED is lit and a buzzer rings, enter the access code.

(Please enter your Access Code in a fast manner since thepower of

the solar panel is weak.)

How to SupplyEmergency Power

Turn the battery cap on theinner lever counterclockwise.

(If it does not open well, use a coin.)

Remove thebattery case cover after removing it from the lever.

Match the +, -polarities shown inside the battery case when

replacing, then close the cover.

When mounting in the lever, turn it clockwise and tighten it

with a coin.

Note that leakage or ruptures may occur when thebattery is inserted in

the wrong way.

False

number

False

number

False

number

P a s s c o d e

How to Change Batteries

- After entering the Access Code +

- If you have entered the correct Access Code,

a “ding” sound occurs

- If you have entered an incorrect Access Code,

a “beep” sound occurs and the Access Mode

is terminated.

- After 5 failed attempts to enter the correct

Access Code, an alarm sound occurs and the

functionis disabled for 3 minutes.

Safety Access

P 6

When Installing the Product

When Using the Product

Symptoms Checklist

- Check that the opposite lever is set in the same direction

or in the default position (90° direction).

After installation, the lever is not set to the

direction in use.

- Check that the batteries are inserted correctly.

- Make sure that the battery pack is properly tightened.

- If there is no problem with the battery and fastening,

reassemble after disassembling.

The power is not turning on.

- This is an alarm sound telling you to replace the battery.

- Replace both batteries with new ones.

An alarm “beep” rings after the product operates.

- There is not enough battery to drive the motor.

- Use the flashlight on your mobile phone to charge

the battery and try again.

- Replace the batteries with new ones immediately.

- Since double locking is set from the inside,

you can open the door after deactivating it.

- Double locking can only be activated and deactivated

manually from inside.

A “beep” sound occurs after entering

the Access Code and the door would not open.

- This is an alarm that occurs when the motor is not

in the locked position.

Place the lever on the proper position and wait until

it is locked.

A motor running sound and a “beep” alarm sound

occurs and the door would not lock automatically.

- This is an alarm sound that occurs when the door is

- Open setting, double lock, access password lock,

Can not be set.

- Try disabling all settings before trying.

not closed properly.

- The sound stops when you click any button.

After opening the door using the Access Code,

a sudden "beep" alarm rings.

I cannot register my access code.

I can not enter Menu mode

- If there is no button input for 15 seconds after entering

the registration mode, the setting is canceled.

- The sign cannot be used as part of the Access Code.

- The Access Code can be a minimum of 4 digits and

a maximum of 12 digits.

A “click” sound occurs after entering

the Access Code and the door would not open.

Manufacturer

AMADAS CO., Ltd

Bldg. 313, #209-1, Institute of Advanced Machinery & Design, Seoul National University,

1, Gwanak-ro, Gwanak-gu, Seoul, Republic of Korea

A/S and Inquiries

+82 2 1522 4802

Learn how to use the opening/closing the

device manually to be prepared for emergency.

Caution

Inhaltsverzeichnis

Andere Amadas Türschloss Handbücher

Amadas

Amadas ADSL-0101T Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung