Amana ABD2233DEQ Bedienungsanleitung

Foral No. A/01/06 Pa_ No. 12828158

m Bottom

Refri Freezer

Important Safety Instructions ............... 1=2

Installation ............................... 3=9

Temperature Controls .................... 10=11

Fresh Food Features ..................... 12-14

Freezer Features ........................... 15

Ice and Water ........................... 16-17

Water Filter ............................. 17-19

Food Storage Tips ....................... 20=22

Care and Cleaning ...................... 23=26

Operating Sounds .......................... 27

Troubleshooting ........................ 28=30

Warranty & Service ......................... 31

Guide d'utilisation et d'entretien ............. 32

Guia de uso ycuidado ...................... 64

www.amana.col. Lidlo U.S.A.

ImportentSefetyinstructions

Installer: Please leave this guide with thB apphance.

Consumer: Please read and keep this Use and

Care Guide for future reference; mtprovides the

proper use and maintenance reformation.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-688-9900 U.S.A.

1-800-688-2002 Canada

1-800-688-2080 (U.S. TTY for hearing or

speech impaired)

(Mon.-Fn., 8 am-8 pm Eastern THee)

Have complete model and senal number

identification of your refrngerator. This is located on a

data plate reside the fresh food compartment, on the

upper right s_de. Record these numbers below for

easy access.

Model Number

Serial Number

Date of Purchase

In our continuing effort to improve the quahty and

performance of our apphances, it may be necessary

to make changes to the apphance without rewsmg

this guide.

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearulg ul

this guide are not meant to cover all possible

cond=tions and situations that may occur. Conlmon

sense, caLitlon and care must be exercised when

installing, maintaining or operating apphance.

Always contact the manufacturer about problems or

conditions you do not understand.

To reduce risk of injury or death, foflow basic

precautions, including the following:

Important: Child entrapment and suffocation are

no_ problems of the past. Junked or abandoned

refrigerators are still dangerous - even mfthey s_t out

for "just a few days." If you are getting nd of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

,Take off the doors.

•Leave the shelves m place so

children may not easily chmb

reside.

This apphance is eqLnpped with a three-prong

grounding plug for your protection against possible

electncal shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibihty and obhgation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground) prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Recognize Safety Symbols, Words,

Labels

DANGER - Immediate hazards which WILL result

in severe personal Injury or death.

WARNING - Hazards or unsafe practices which

COULD result m severe personal injury or death.

CAUTION - Hazards or unsafe practices which COULD

result m minor personal injury or property damage.

Grounding type

wall receptacle

ImportentSefetyinstructions

To reduce risk of fire, electric shock, serious injury or 13. Always disconnect refrigerator from electrical

death when using your refrigerator, follow these basic supply before attempting any service. Disconnect

precautions, including tile following: power cord by grasping the plug, not tile cord.

1. Read all instructions before using tile refngerator. 14.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electnclan mfyou are not

sure thB apphance _sproperly grounded. 15.

5. Do not ground to a gas hne.

6. Do not ground to a cold-water p_pe.

7. Refngerator _sdesigned to operate on a separate

115 volt, 15 amp., 60 cycle hne. 16.

8. Do not modify plug on power cord. If plug does 17.

not fit electrical outlet, have proper outlet installed

by a quahfled electrician.

9. Do not use a two-prong adapter, extension cord 18.

or power strip.

10. Do not remove warning tag from power cord. 19.

11. Do not tamper w_th refrigerator controls.

12. Do not serwce or replace any part of refrigerator 20.

unless spec#lcally recommended m Use & Care

Guide or pubhshed user-repmr instructions. Do

not attempt serwce _finstructions are not

understood or _fthey are beyond personal skill

level.

Install refngerator according to Installation

Instruct,ons. All connections for water, electncal

power and grounding must comply with local

codes and be made by hcensed personnel when

requmred.

Keep your refngerator in good condition. Bumping

or dropping refrigerator can damage refngerator

or cause refngerator to malfunctnon or leak. If

damage occurs, have refrigerator checked by

quahfled service techmclan.

Replace worn power cords and/or loose plugs.

Always read and follow manufacturer's storage

and mdealenwronment instructions for _tems being

stored m refrigerator.

Your refrigerator should not be operated In tile

presence of exploswe fumes.

Children should not chmb, hang or stand on any

part of the refrigerator.

Clean up spills or water leakage associated with

water installation.

SAVE THESE INSTRUCTIONS

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow '/2"space at top and '/Z space behind the

machine compartment cover (located in the rea0 for

proper air circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

•NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging the

refrigerator in immediately may cause damage to

internal parts.

Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

•Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Leveling

To enhance the appearance and maintain performance,

the refrigerator should be level.

NOte-" Complete any required door reversal, panel

installation and/or a water supply connection, before

leveling.

Materials Needed

•3/8"hex head driver

•Carpenter's level

1. Remove toe grille.

•Grasp firmly and pull outward

to unclip.

2. Remove bottom bracket cover(s).

•Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

•Use slight pressure to pry the

cover loose.

Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

3. Usinghexheaddriver,turnthefrontadjustment

screws(A)oneachsideto raiseorlowerthefront

oftherefrigerator.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

C C

i Note-" Some models only have adjustment screws

,:A:,

4. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

5. Using the carpenter's level, make sure front of

refrigerator is Y4"(6 ram) or '/zbubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs (C) clockwise until firmly

against floor.

7. Freezer drawer models only: Turn adjustment

screws (A) counterclockwise to allow the full

weight of the refrigerator to rest on the stabilizing

legs.

8. Replace bracket cover(s).

• Position cover into the outer edge of the hinge.

•Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

i Note." For proper reinstallation, follow the "top"marking on the interior of the toe grille.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

1. Unplug power cord from power source.

2. Remove toe grille and bottom bracket

cover(s) (see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

Unscrew -_,6"hex head screws from

top hinge to remove hinge and retain

all screws for later use.

Lift refrigerator door from center

hinge pin.

For swing freezer door models

only: Hold freezer door while

removing hinge pin with a t,6" hex

head driver. Remove door from

bottom hinge and retain hinge pin

for later use.

For pullout freezer drawer models

only: Remove plastic sleeve, if l

Remove center hinge pin with a ?,_"hex"

head driver. Retain hinge pin and

plastic sleeve for later use.

Remove Phillips screws to remove

center hinge and retain all screws for

later use.

Remove bottom hinge or stabilizing

bracket with -7_"hex head driver and

retain screws for later use. Lift out

bottom hinge pin (on freezer door

models).

If your model has a pullout freezer drawer, see

page 5 for drawer removal instructions.

To Install:

1. Pull both rails out to full

extension.

2. While supporting door front,

hook supports into tabs

located on inside of rail.

3. Lower door front into

final position.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

Lift lower basket straight up and out to remove.

On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

5. Remove Phillips screw

from each side of rail

system (select models).

6. Lift top of drawer front

to unhook supports

from rail system. Lift

door front out to

rein ove.

.Replace and tighten Phillips screws that were

removed from each side of rail system (select

models:).

Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

With rails pulled out to full extension, set the

basket straight down into the basket cradles.

Basket cradle

7. Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch. f

Reinstallation of the Doors

1. install hinge assemblies:

•install top hinge loosely with %" hex head

sorews.

• install center hinge with Phillips screws.

•Freezer door models: install bottom hinge with

3/8"hex head screws.

2. Freezer door models: insert bottom

hinge pin.

• Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

3. Freezer door models: Place hinge

side of freezer door on bottom hinge

pin and hold freezer door upright

while installing center hinge pin with

_/,6"hex head driver.

• Replace plastic sleeve.

• Replace any applicable door shims.

• Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator

door on center hinge pin.

5. While holding refrigerator door

upright, tighten down top hinge

with _/,6"hex head driver and

replace hinge cover.

Door Reversal

In some installations, reversing the door swing allows

for more convenient access to stored items. Both

doors can be reversed on freezer door models and the

fresh food door is reversible on freezer drawer models.

1. Remove door(s) (see page 4).

2. Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

• Remove cabinet plugs with flat

blade of screwdriver tip wrapped

in masking tape.

• Remove center mullion screws

with _/,;' hex head screwdriver.

•Freezer door models: Remove

bottom mullion screws with 3/8"hex head driver.

3. Transfer door stops from bottom edge of fresh food

door and freezer door, if applicable, to opposite

side of door edge.

• Use a Phillips screwdriver

for removal and installation.

4. install handles (see pages 6,

7 or 8).

'---.....

5. Reinstall the door(s).

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Fresh Food Handles

Standard Front Mount Handle

Materials Needed

•Phillips screwdriver

•_/,_"hex head driver

To Install:

1. Remove '/4"hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

• If reversing door, remove door

plugs from opposite side of door

and insert in screw holes.

2. Align handle holes with screw holes on t 1

door face and secure with two door face

screws from step 1.

3. Locatehandletrimin literaturepackand

installovertopandbottomof handle,as

illustrated.

*Secure top handle trim with remaining

screw removed in step 1.

Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing

top handle screw.

•Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

• Retain trim for later replacement.

3. Remove two hex head screws.

*Retain screws for later replacement.

Side Mount Handle

Materials Needed

*Phillips screwdriver

To Install:

1. Remove screws from the side of the

doon

2. Align the side mount handle with the

predrilled holes in the door panel.

3. insert the screws in the sequence as

shown.

Lower

Handle

4. Ensure the door handle is snug to the

door panel.

To Remove:

Reverse installation procedure.

Freezer Handles

Partial-Width Handle

Materials Needed

*Phillips screwdriver

To Install:

1. Install handle by fastening with

screws removed from edge of door.

If reversing freezer door, remove

door plugs from top edge of door

and insert into screw holes.

To Remove:

1. Remove handle screws with Phillips

screwdriver and retain screws for

later use.

t II

Front Mount Freezer Handle

Materials Needed

Gloves to protect hands.

Phillips screwdriver.

•Plastic handle removal card (or '_2"thick plastic

card:). Retain the card.

Notes:

There is a slight curve to

this style of freezer

handle.

,, For proper installation, be

sure handle is oriented as

shown.

To install:

1. Align door handle clips slightly to the left of the

tabs attached to the freezer door.

2. Rotate the handle so the left base is flat against

the door.

Handle Door

3. Pushthelefthandle

baseagainsttheleft

doortabandslightly ......

totheright,just

enoughto allowitto ..................

hangunsupported.

4.Whilefirmlysupportingthelefthandlebaseagainst

thedoor,aligntherightbaseofthehandlewiththe

righttabsthatareattachedtothedoor.

5. Now,whilefirmlyholdingthehandleattheleftand

rightbases,gentlyslidethe handletowardsthe

rightuntiltherightbasesettlesin.Thehandle

shouldnowbeflatagainstthefaceofthefreezer

doorat boththeleftandrightbases.

6.Withhandsstillfirmlykeepingthehandleflat

againstthefreezerdoor,youmayhavetoreverse

directionsmomentarilyto assureclip/tab

engagement.Thenfirmlyslidethehandletothe

rightuntilit clicks.Theaudible"click"indicates

thatthefasteningclipsaresecurelyinterlocked.

To Remove:

1. At the right end, flex the handle base away from

the surface of the freezer drawer. Simultaneously

slide the door handle removal card that came with

your refrigerator under the right side base of the

handle. Slide the card to the line indication or until

it stops, which will be approximately 1'/_".

2. With both hands, firmly grasp the handle towards

the right base.

3. Slide toward the left, lift and remove from the

surface.

Connecting the Water Supply

Cselect models)

To reduce the risk of injury or death, follow

basic precautions, including the following:

• Read all instructions before installing ice maker.

,Do not attempt installation _finstructions are not

understood or if they are beyond personal skill

level.

° Observe all local codes and ordinances.

Do not service racemaker unless specifically

recommended m Use & Care Grade or pubhslled

user-repaw instructions.

Disconnect power to refrigerator before mstalhng

ice maker.

+ Water damage due to an u_proper water

connecbon may cause mold/mildew growth.

Clean up spills or leakage uamedlately.

To avoid property damage or possible injury,

follow basic precautions, including tile

following:

°Consult a plumber to connect , O.D. copper

tubing to household plumbing to assure

comphance with local codes and ordinances.

+ Confirm water pressure to water valve _sbetween

35 and 100 pounds per square inch.

+ Do not use a self-piercing, or -1,+"saddle valve.

Both reduce water flow can become clogged over

tulle, and may cause leaks if repaw is attempted.

+ Tmghten nuts by hand to prevent cross threading.

FmBh bghtenmg nuts with phers and wrenches.

Do not overt_ghten.

+Wmt 2-3 hours before placing refrigerator into final

potation to check and correct any water leaks.

Reclleck for leaks after 24 hours.

+ Verify tile copper tubing under the sleeve is

smooth and free from defects. Do not reuse an old

sleeve.

Materials Needed

+'2' outer diameter flexible copper tubing

+Shut-off valve (requwes a L" hole to be drilled into

water supply line before valve attachment)

+Adjustable wrench

+_" hex nLIt driver

Note: Add 8' to tubing length needed to reach

water supply for creation of service loop.

1. Create service loop with copper

tubing (mulimum 2+diameter).

Avoid kinks m the copper tubing

when bending it into a seMce

loop.

Remove plastic cap from water valve inlet _

port. olluo .

3. Place brass nut (A) and sleeve (B) A B

on copper tube end as illustrated.

Important: Do not use an old

sleeve.

4. Place end of copper tubing into water

valve inlet port. Shape tubing shghtly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

Important: Do not over-tighten. Cross

threading may occur.

.Pull oil tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn oil

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to _ts permanent

location.

j,i

_:]]:ou

i ©

_4]y.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Amana Kühlschrank Handbücher

Amana

Amana REFRIGERATOR Bedienungsanleitung

Amana

Amana 10488010 Bedienungsanleitung

Amana

Amana ASD2522WRD02 Bedienungsanleitung

Amana

Amana ARS9167A Handbuch

Amana

Amana ASD2524VE Gebrauchsanweisung

Amana

Amana ABR2222FES Stücklistenhandbuch

Amana

Amana AFB2234WES2 Bedienungsanleitung

Amana

Amana FRS-4041I Bedienungsanleitung

Amana

Amana Side-by-Side Refrigerator Bedienungsanleitung

Amana

Amana Side By Side Refrigerator Bedienungsanleitung

Amana

Amana ARB1917CW-PARB1917CW1 Bedienungsanleitung

Amana

Amana BX22S5W Bedienungsanleitung

Amana

Amana AFI2538AEW Bedienungsanleitung

Amana

Amana SXD25S2 Montageanleitung

Amana

Amana ARB1905CC0 Bedienungsanleitung

Amana

Amana BR22TW-P1196709WW Bedienungsanleitung

Amana

Amana ABL2222FES3 Fehlerbehebungshandbuch

Amana

Amana BX518V Bedienungsanleitung

Amana

Amana Side-by-Side Refrigerator Bedienungsanleitung

Amana

Amana ASD2620HRZ Bedienungsanleitung

Amana

Amana FRS-4041CAL Bedienungsanleitung

Amana

Amana ABL2227FES12 Bedienungsanleitung

Amana

Amana AB2225PEKS Bedienungsanleitung

Amana

Amana DB11 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung