Amazon B07GF58DXB Bedienungsanleitung

B07GF58DXB

Barn Door Hardware 6.6 ft - J Shape - Black

Herraje para Puertas de Granero de 2m (6,6 pies) - Forma en J - Negro

Ferrure de Porte de Grange 2 m (6,6 pieds) - en Forme de J -Noire

6.6 ft (2 m)

English ..................................... 3

Español.................................. 14

Français ................................. 25

Welcome Guide •English

Contents:

Before getting started, ensure the package contains the following components:

Ax1 E4 x4

Bx5 Fx1

C1 x1 F1 x2

C2 x1 F2 x2

C3 x1 Gx5

Dx2 G1 x5

E1 x4 H1 x2

E2 x4 H2 x2

E3 x8

Tools you will need

Electric drill

Tape measure

Screwdriver Wrench and

socket set

Level Router

Drill bit

7/64” (2.8 mm),

1/8” (3 mm),

1/4” (6.5 mm),

5/16” (8 mm),

7/16” (11 mm)

Marking tools

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed

to a third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of

injury including the following:

• If your door opening has trim around it, it is recommended that you install the track onto a

header board above the door opening.

• If your door opening does not have trim around it, the track can be installed directly into the

drywall provided you ﬁnd the studs in your walls.

• The track CANNOT be mounted directly into the drywall.

Before First Use

• Check for transport damage.

Risk of suffocation! Keep any packaging materials away from children – these

materials are a potential source of danger, e.g. suffocation.

DANGER

Installation

Step 1: Track Preparation

Door height +

1.75" (44 mm)

Keep level

Door opening

Floor

Door

2” (51 mm) minimum

on one side of

the door

Header board

(1 x 6 recommended)

Floor clearance:

Using the dimensions

shown will allow for a

3/8” (9.5 mm) space

between the door

and ﬂoor.

If your door opening DOES NOT have trim going around it, follow the below

steps.

1. Using the layout above as reference, position the track where you would like it.

2. Using a stud ﬁnder, locate the studs where you want to attach the track.

3. Using a small nail, tap it into the drywall and make sure you have located the stud.

4. Using a pencil, mark the location of the stud.

5. Repeat steps 2 and 3 until you have ﬁve marks indicating you have found ﬁve wall studs.

6. Place the track on the wall and make sure the ﬁve pencil marks on the wall match up with the

ﬁve holes in the track.

7. If the holes in the track DO ALIGN with the marks on the wall, proceed to Track Installation.

8. If the holes in the track DO NOT ALIGN with the marks on the wall, then a header board will

need to be used.

NOTICE

Installation

Step 2: Header Board Installation

Door height + 1.75” (44 mm)

Keep level

Door opening

Floor

2” (51 mm) minimum

on one side of the

door

Header board

(1 x 6 recommended)

Floor clearance:

Using the dimensions

shown will allow for a

3/8” (9.5 mm) space

between the door

and ﬂoor.

Draw a straight vertical line of at least 3.5” (89 mm), going through the mark

that you made for the stud location.

1. Locate and mark the center of the 1 x 6.

2. Using the center line of the header board, line it up to the stud marks.

3. Using interior screws, mount the header board to the wall.

Use a level to ensure the header board is level when installing it to the studs.

NOTICE

Installation

Step 3: Track Installation

Attaching the track directly to the studs:

1. Using the 5 marks you made, drill a 1/4” (6 mm) pilot hole 1” - 3” (25 - 76 mm) deep on each

mark.

2. Slide the washer (G1) over the screw (G) and repeat for all 5 screws.

If the door is going to stop before the last hole (8” / 20 cm) on either end, then

the door stop C1 or C2 will need to be installed onto the rail ﬁrst.

3. Position the track over the drilled holes.

4. Starting at one end of the track, insert the screw (G) through the track and then through the

spacer (B) and into the pilot hole.

5. Use a wrench to tighten the screw.

Do not tighten the screw completely until all screws are installed and the track

is level.

6. Repeat steps 4 and 5 for the remaining holes (checking with a level for each screw installed).

NOTICE

Attaching the track to the header board:

1. Place the track in the center of the header board and determine where you want it to be

installed.

Make sure the track is level before making your hole marks.

2. Mark locations for all 5 holes.

3. Using the 5 marks you made, drill a 1/4” (6 mm) pilot hole 1” - 3” (25 - 76 mm) deep on each

mark.

4. Follow steps 2 through 6 under “Attaching the track directly to the studs”.

Installing door stops

1. Slide one door stop (C1, C2) on each end of the tack, making sure the hex screws are facing

up and the actual stops are facing the door.

2. Determine where you want the door to stop in both directions, then move the door stop to that

location and tighten down the hex screws with the hex wrench.

Step 4: Installing Hangers and Anti-Jump Disc

2 - 7/16” (62 mm)

1 - 1/2” (38 mm) 1 - 1/2” (38 mm)

3 - 9/16” (90 mm) 3 - 9/16” (90 mm)

Ø7/16” (11 mm)

2” (51 mm)

NOTICE

Installing hanger brackets

1. Starting from the left side of the door, measure in 2” (51 mm) and make a mark.

2. Measure down 1-1/2” (38 mm) and make a mark.

3. Take the hanger bracket and center the top hole over the line intersection.

4. Mark the bottom hole (making sure the center of the bottom hole is 2” (51 mm) away from the

door edge).

5. Remove the bracket and drill a 7/16” (11 mm) hole through the door for each bracket hole.

Door thickness will determine which bolt size to use.

6. Slide the washer (E3) over the screw (E1 or E2) and insert through the back of the door.

7. Slide the washer (E3) over the screw and screw on nut (E4), then hand-tighten.

8. Repeat steps 6 and 7 for the bottom hole.

9. Tighten down nuts.

10.Repeat for other side.

Installing anti-jump disk

1. Measure 2-7/16” (62 mm) from the inside of the hanger and make a mark in the center of the

door edge.

2. Screw the anti-jumper disc into the door top.

3. Do not tighten the anti-jumper disc all the way.

Prior to hanging the door, the anti-jump discs must be hanging over the front

edge of the door.

4. Repeat for other side.

NOTICE

Installation

Step 5: Hanging Door

1. Lift the door onto the track.

2. Turn the anti-jumper discs to where they are now centered on the door edge.

3. Tighten.

Inhaltsverzeichnis

Sprachen:

Andere Amazon Türöffnungssystem Handbücher

Amazon

Amazon B07GDXCX87 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung