Amazon 90DM160 Bedienungsanleitung

4000 Count Auto Ranging Digital Multimeter

Multimètre Numérique 4000Points à Sélection Auto de la

Plage de Mesure

4000er-Zählung Automatisch Messender Digitalmultimeter

Multimetro Digitale a Selezione Automatica del Campo di

Misurazione, 4000Conteggi

Multímetro Digital de Alcance Automático, Contador Hasta 4000

4000Counts Digitale Multimeter met Automatische Bereikinstelling

B083V7BMZR

10A

English . . . . . . . . . . . . . . . . . . . . . . . 3

Français . . . . . . . . . . . . . . . . . . . . . 32

Deutsch . . . . . . . . . . . . . . . . . . . . . 63

Italiano . . . . . . . . . . . . . . . . . . . . . . 94

Español . . . . . . . . . . . . . . . . . . . . 125

Nederlands . . . . . . . . . . . . . . . . . 155

IMPORTANT SAFETY

INSTRUCTIONS

Read these instructions carefully and retain them for

future use. If this product is passed to a third party,

then these instructions must be included.

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric

shock, and/or injury to persons including the following:

WARNING Risk of electric shock! Improper use of this

product can cause damage, shock, injury or death.

WARNING Risk of electric shock! The safety features of

this product may not protect the user if not used in accordance

with this user manual.

WARNING Risk of electric shock! Take special care while

working under wet conditions. Humid objects and air have an

increased conductivity.

CAUTION Risk of short circuit! Use the test probe

shrouds to avoid accidental short circuiting if the components

or test points are too near each other. Operation is limited to

CAT II applications when the insulated tips are removed from

one or both test probes. Refer to Speciﬁcation in this manual for

maximum voltage ratings.

WARNING Risk of electric shock! Use special care

when making measurements, if the voltages are greater than

25V~ RMS or 35V . These voltages are considered a shock

hazard.

WARNING Risk of electric shock! Keep ﬁngers away

from the metal probe tips when taking measurements.

WARNING Risk of explosion! Do not use the product

near explosive vapors, dust or gases.

CAUTION Risk of injury! The probe tips are sharp for

accuracy. Be careful when handling and reattach the probe tip

shrouds after use.

• This product is intended for measurements on electrical

installations and is protected by doubleinsulation as per

EN61010-1 to CATIII600 V; Pollution Degree 2.

• This product must be used by trained users only.

• Do not measure current on a CATIII circuitry whose voltage

exceeds 600V.

• When measuring volts, do not switch to current/resistance

modes.

• Set the function switch to the appropriate position before

measuring.

• Set the function switch to the OFF position when not in use.

• Inspect the condition of the connector leads and the product

for any damage before operation. Replace any damaged

accessory before use. Consult a professional repair centre

for any other repairs.

• Do not exceed the maximum allowable input range of any

measurement mode.

Mode Maximum Input

A~, A 10 A, 600 V fast acting fuse (max.

30seconds every 15minutes)

mA~, mA 500 mA, 600 V fast acting fuse

V~, V 600 V ~RMS /

Frequency,

Resistance,

Capacitance, Diode

Test, Continuity,

Temperature

250 V ~RMS /

Surge Protection: 8 kV peak per EN61010

• When changing ranges always disconnect the connector

leads from the circuit under test.

• Always discharge capacitors and remove power from the

device under test before performing diode, resistance or

continuity tests.

• Voltage checks on electrical outlets can be difﬁcult and

misleading because of the uncertainty of connection to the

recessed electrical contacts. Do not use this product for

checking socket outlets. Use special equipment for checking

socket outlets.

• Comply with all applicable safety codes. Use approved

personal protective equipment when working near live

circuits − especially with regard to the possibility of arc ﬂash

hazards.

• Always remove the connector leads before replacing the

battery or fuses.

Battery Warnings

• Always insert batteries correctly with regards to polarity

(+ and –) marked on the battery and the product.

• Exhausted batteries should be immediately removed from

product and properly disposed.

• Keep batteries out of the reach of children.

• Do not dispose of batteries in ﬁre.

• Remove batteries from product if it is not to be used for an

extended period of time.

• If the battery leaks, avoid contact with skin and eyes. Rinse

affected areas immediately with plenty of clean water, then

consult a doctor.

Explanation of Symbols

WARNING The signal word that indicates a hazard with

a medium level of risk which, if not avoided,

could result in death or serious injury.

CAUTION

The signal word that indicates a hazard

that if not prevented could result in minor or

moderate injury.

NOTICE Indicates a practical tip, advice or practice

not related to personal injury.

This symbol stands for “Conformité Européenne”,

which means “Conformity with EU-directives”. With

the CE marking the manufacturer conﬁrms that this

product complies with applicable European directives

and regulations.

This symbol, adjacent to another symbol or terminal,

indicates the user must refer to the manual for

further information.

This symbol, adjacent to a terminal, indicates that,

under normal use, hazardous voltages may be

present.

Product is protected by double insulation or

reinforced insulation.

Alternating current (AC).

Direct current (DC).

Fuse

Earth (ground) terminal/potential.

CAT II

600V

Product is designed to protect the user during

measurements performed on circuits directly

connected to the low voltage installation.

CAT III

600V

Product is designed to protect the user during

measurements performed in the building installation

(up to 600 V).

Intended Use

• This product is intended to perform electrical measurements

on CAT III locations (3-phase and single phase distribution).

• This product covers CAT II and CAT I locations.

• This product may be used only under the conditions and for

the purposes for which it was designed.

• No liability will be accepted for damages resulting from

improper use or non-compliance with these instructions.

Before First Use

• Check the product for transport damages.

• Remove all the packing materials.

DANGER Risk of suffocation! Keep any packaging

materials away from children – these materials are a potential

source of danger, e.g.suffocation.

Product Description

10A

MQR

ANon-contact voltage

indicator JHOLD/ button

BDisplay KBattery compartment

CRANGE button L500 mA fuse

DMODE button M10 A fuse

EFunction switch NTilt stand

F10A input jack OTest probes with

connector leads

GCOM input jack PProbe tip shrouds

HV/Ω/Temp/Hz/%

/mA/μA input jack QTemperature probe

IREL Relative button R

Temperature probe

adapter with protection

cups

Inhaltsverzeichnis

Sprachen:

Andere Amazon Messgerät Handbücher

Amazon

Amazon B005PJJ89U Bedienungsanleitung

Amazon

Amazon P3A7EN Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung