Ambient Weather TESA WS710 Bedienungsanleitung

Table of Contents

…………………………..……….……………………….....2

.……….……………………………...............................2

……….…………………………......…………………...2

……….……………………………..…..…..…..2

.……….………………….....2

……….………………………...…..…….5

.……….………………….…….......6

……….……………………....7

……….………………......…………….......8

……….……………………………...…...…...…….....8

….……………………………......…………...............8

………………………....….….….……......8

……….…………………………………………….8

……….……………………………………….

...…….…………..……...........9

....……………. ....………. …9

……….…………………….…......……….9

… … ...… … … … .9

… … .… … … … … … .… … ......… … 10

……….……...……………......…….11

…….….……………......…… … 11

… … … .… … .....… … … ...................… … … .12

……….…………………………....………………….12

……….……......………………......…….12

… ...… .… … … … … ......… … .12

… … … .… … … … … … ......… … … .… … 13

….........……………………….…….………13

1. Introduction

2.Getting Started

2.1 Parts List

2.2 Recommend Tools

2.3 Thermo-Hygrometer Sensor Set Up

2.4 Display Console Set Up

2.4.1 Display Console Layout

2.4.2 Sensor Operation Verification

3.Remote Sensor Installation

4.Display Features

4.1 Comfort Icon

4.2 Rate of Change Icon

5.Console Operation

5.1 Min/Max Mode ........8

5.2 Indoor/Outdoor Channel Selection

5.3 Temperature Units of Measure ... ...

5.4 Sensor Search Mode

5.5 Best Practices for Wireless Communication

5.6 Adjustment or Calibration

5.6.1 Humidity Calibration

5.6.2 Temperature Calibration

6.Glossary of Terms

7.Specifications

7.1 Wireless Specifications

7.2 Measurement Specifications

7.3 Power Consumption

8.Troubleshooting Guide

WS710 Wireless Indoor/Outdoor 8-Channel

Thermo-Hygrometer with Daily Min/Max Display

INSTRUCTION MANUAL

-1-

1. Introduction

Thank you for your purchase of the WS710 Wireless Indoor/Outdoor

8-Channel Thermo-Hygrometer with Jumbo Display. The following user

guide provides step by step instructions for installation, operation and

troubleshooting.

2.Getting Started

Note: The power up sequence must be performed in the order

shown in this section (insert batteries in the remote transmitter(s) first,

Display Console second).

The unit consists of a display console (receiver), and a thermo-

hygrometer (remote transmitter).

2.1 Parts List

2.2 Recommend Tools

Hammer and nail for hanging remote thermo-hygrometer transmitter.

2.3 Thermo-Hygrometer Sensor Set Up

1. Remove the battery door on the back of the sensor by

removing the set screw, as shown in Figure 1 .

QTY Item

Display Console

Frame Dimensions (LxHxW): 11.4x12.7x2.5cm

LCD Dimensions (LxW): 9.5x8.9cm

LCD Segment Height: 3.2cm

Thermo-hygrometer transmitter

Dimensions (LxHxW): 11.4x5x2.0cm

-2-

LED

Figure 1

2. BEFORE inserting the batteries, locate the dip switches on

the inside cover of the lid of the transmitter.

Figure 2

setting).

Figure 2

3. Channel Number: The WS710 supports up to eight

transmitters. To set each channel number (the default is Channel 1),

change Dip Switches 1, 2 and 3, as referenced in Table 1.

4. Temperature Units of Measure: To change the transmitter

display units of measure (°F vs. °C), change Dip Switch 4, as referenced

in Table 1.

displays all four switches in the OFF position (factory default

-3-

Table 1

5. Insert two AAA batteries.

6. After inserting the batteries, the remote sensor LED indicator will

light for 4 seconds, and then flash once per 60 seconds thereafter.

Each time it flashes, the sensor is transmitting data.

7. Verify the correct channel number (CH) and temperature units of

measure (°F vs. °C) are on the display, as shown in Figure 3.

Figure 3

(1) temperature

(2) temperature units (°F vs. °C)

(3) channel number

(4) relative humidity

DIP SWITCH FUNCTION

Channel 1

Channel 2

Channel 3

Channel 4

Channel 5

Channel 6

Channel 7

Channel 8

°F

°C

-4-

8. Close the battery door. Make sure the gasket (around the

battery compartment) is properly seated in its trace prior to closing

the door. Tighten the set screw.

2.4 Display Console Set Up

1. Move the remote thermo-hygrometer(s) about 1.5m to 3m away

from the display console (if the sensor is too close, it may not be

received by the display console). If you have more than one

thermo-hygrometer, make sure they are all powered up and

transmitting on different channels.

2. Remove the battery door on the back of the display, as shown in

Figure 4. Insert four AAA (alkaline or lithium, avoid rechargeable)

batteries in the back of the display console

Figure 4

All of the LCD segments will light up for a few seconds to verify all

segments are operating properly.

3. Replace the battery door, and fold out the desk stand and place the

console in the upright position.

The console will instantly display indoor temperature and humidity

as designated by the icon. The remote temperature and humidity

will update on the display within a few minutes on the appropriate

channel.

-5-

While in the search mode, the remote search icon will be

constantly displayed.

If you have more than one remote sensor (up to eight remotes are

supported), the display will automatically toggle between sensors

until all sensors have reported in.

Do not touch any buttons until the remote sensor has reported in, or

the radio search icon is no longer on, otherwise the remote

sensor search mode will be terminated. When the remote sensor

temperature and humidity has been received, the console will

automatically switch to the normal mode, and all further settings can

be performed.

If the remote does not update, please reference the troubleshooting

guide in Section 8 .

2.4.1 Display Console Layout

Note: The following illustration shows the full segments of the

LCD for description purposes only and will not appear like this during

normal operation.

Figure 5

1. Temperature

2. Min/Max Record mode

2 3

-6-

3. Temperature, Rate of Change indicator

4. Temperature units (°F or °C)

5. Humidity, Rate of Change indicator

6. Relative Humidity (%)

7. Humidity Comfort Icon

8. Reception Icon (solid when searching, flashes when updating)

9. Channel 1,2,3,4,5,6,7,8, indicator

2.4.2 Sensor Operation Verification

Verify the indoor and outdoor humidity match closely with the console

and sensor array in the same location (about 1.5 to 3 meters apart).

The sensors should be within 10% (the accuracy is ± 5%). Allow about

30 minutes for both sensors to stabilize. The humidity can be adjusted

or calibrated later to match each other a known source.

Verify the indoor and outdoor temperature match closely with the

console and sensor array in the same location (about 1.5 to 3 meters

apart). The sensors should be within 2°C (the accuracy is ± 1°C). Allow

about 30 minutes for both sensors to stabilize. The temperature can be

adjusted or calibrated later to match each other or a known source.

3. Remote Sensor Installation

It is recommended you mount the remote sensor on a south facing

wall, in a shaded area. Direct sunlight and radiant heat sources will

result in inaccurate temperature readings. Although the sensor is water

resistant, it is best to mount in a well protected area, such as under an

eve. Use a screw or nail (not included) to affix the remote sensor to the

wall, as shown in Figure 6.

Figure 6

-7-

4. Display Features

4.1 Comfort Icon

The comfort icon is based on humidity ranges specified in Figure 7 .

The icon is displayed for indoor humidity, remote channel 1 humidity

and optional remote channels 2 through 8 humidity.

Figure 7

4.2 Rate of Change Icon

The rate of change icon detects rapid changes in temperature and

humidity. If the arrow points upward, the temperature is increasing at a

rate of +2°C per 30 minutes (or greater), or humidity is increasing at a

rate of +5% per 30 minutes (or greater). If the arrow points downward,

the temperature is decreasing at a rate of -2°C per 30 minutes (or less),

or humidity is decreasing at a rate of -5% per 30 minutes (or less).

5. Console Operation

Note: The console has three buttons for easy operation:

MIN/MAX/- button, CLEAR/ADJUST button, and CHANNEL/+ button.

5.1 Min/Max Mode

The Min/Max mode displays the minimum and maximum temperature

and humidity (since reset of the unit) for the indoor, remote channel 1

through 8 sensors.

Prior to entering the MIN/MAX mode, press the CHANNEL/+ button to

select the temperature and humidity values you wish to view.

1. Display Maximum. Press the MIN/MAX button once to display

the maximum. The MAX icon will be displayed.

2. Clear Maximum. To reset the maximum values to the current

values, press and hold the CLEAR button for 3 seconds.

RH<45% RH45%~65% RH>65%

Dry Comfortable Wet

-8-

3. Display Minimum. Press the MIN/MAX button again to

display the minimum. The MIN icon will be displayed.

4. Clear Minimum. To reset the minimum values to the current

values, press and hold the CLEAR button for 3 seconds.

To return to normal mode, press the MIN/MAX button again.

5.2 Indoor/Outdoor Channel Selection

Press the CHANNEL/+ button to switch the display between the indoor

temperature and humidity ,remote sensors 1 through 8, and scroll

mode .In scroll mode, all of the indoor and detected outdoor sensors

will be displayed in five second intervals.

5.3 Temperature Units of Measure

The default temperature units of measure are degrees Celsius. To toggle

between degrees Celsius and degrees Fahrenheit, press and hold the

MIN/MAX button for 3 seconds.

5.4 Sensor Search Mode

If any of the sensor communication is lost, dashes (--.-) will be displayed

on the screen. To reacquire the signal:

1. If a specific channel is lost, press the CHANNEL/+ button to

display this channel, then Press and hold the CHANNEL/+ button

for 3 seconds, and the remote search icon will be constantly

displayed for up to 10 minutes. Once the signal is reacquired, the

remote search icon will turn off, and the current values will be

displayed.

2. If new sensors are added, subtracted, or multiple sensor channels

are lost, press the CHANNEL/+ button until the indoor channel

is displayed. Press and hold the CHANNEL/+ button for 3

seconds, and the remote search icon will be constantly

displayed for up to 10 minutes. Once the signal is reacquired, the

remote search icon will turn off, and the current values will be

displayed.

5.5 Best Practices for Wireless Communication

Wireless communication is susceptible to interference, distance, walls

and metal barriers. We recommend the following best practices for

trouble free wireless communication.

-9-

1. Electro-Magnetic Interference (EMI). Keep the console several

feet away from computer monitors and TVs.

2. Radio Frequency Interference (RFI). If you have other 433

MHz devices and communication is intermittent, try turning off

these other devices for troubleshooting purposes. You may

need to relocate the transmitters or receivers to avoid

intermittent communication.

3. Line of Sight Rating. This device is rated at 100 meters line of

sight (no interference, barriers or walls) but typically you will get

30 meters maximum under most real-world installations, which

include passing through barriers or walls.

4. Metal Barriers. Radio frequency will not pass through metal

barriers such as aluminum siding. If you have metal siding,

align the remote and console through a window to get a clear

line of sight .

5.6 Adjustment or Calibration

Note: The calibrated value can only be adjusted on the console.

The remote sensor(s) always displays the un-calibrated or measured

value.

Note: The measured humidity range is between 10 and 99%.

Humidity cannot be accurately measured outside of this range.

The purpose of calibration is to fine tune or correct for any sensor error

associated with the devices margin of error. The measurement can be

adjusted from the console to calibrate to a known source.

Calibration is only useful if you have a known calibrated source you

can compare it against, and is optional. This section discusses

practices, procedures and sources for sensor calibration to reduce

manufacturing and degradation errors. Do not compare your readings

obtained from sources such as the internet, radio, television or

newspapers. They are in a different location and typically update once

per hour.

-10-

Inhaltsverzeichnis

Andere Ambient Weather Wetterstation Handbücher

Ambient Weather

Ambient Weather WS-G3303THB Bedienungsanleitung

Ambient Weather

Ambient Weather OBSERVER WS-1550-IP Bedienungsanleitung

Ambient Weather

Ambient Weather WS-2000 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1551-IP Bedienungsanleitung

Ambient Weather

Ambient Weather WeatherHub2 Bedienungsanleitung

Ambient Weather

Ambient Weather WEATHER WINDOW Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1070 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-8478 FALCON Bedienungsanleitung

Ambient Weather

Ambient Weather Fischer 1508B-45 Bedienungsanleitung

Ambient Weather

Ambient Weather GL164-M Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1900A Bedienungsanleitung

Ambient Weather

Ambient Weather WS-2801 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-290D Bedienungsanleitung

Ambient Weather

Ambient Weather WS-7079 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-2090 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-0800-IP ObserverBase Bedienungsanleitung

Ambient Weather

Ambient Weather WS-5300 Bedienungsanleitung

Ambient Weather

Ambient Weather OBSERVER WS-1002-WiFi Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1171A Bedienungsanleitung

Ambient Weather

Ambient Weather WS-50-C Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1400-IP OBSERVER Bedienungsanleitung

Ambient Weather

Ambient Weather WS-L3303THB Bedienungsanleitung

Ambient Weather

Ambient Weather WS11 Bedienungsanleitung

Ambient Weather

Ambient Weather WS-1900 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung