American DJ Accu Scan 250 Montageanleitung

American DJ®

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Rev. 2/06

User Instructions

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 2

Unpacking: Thank you for purchasing the Accu Scan 250™ by Amer-

ican DJ®. Every Accu Scan 250™ has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your ﬁxture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support ﬁrst.

Introduction: The Accu Scan 250™ is a eight channel, intelligent

DMX scanner. The fixture can operate in three different operating

modes; stand alone, sound-active, or in a Master/Slave configuration.

The Accu Scan 250™ comes with several built in programs and is best

used in multiples of four. When used as a stand alone unit or when used

in multiples linked in a master/slave configuration. For best results use

fog or special effects smoke to enhance the beams projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the lamp.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Accu Scan 250™ General Information

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 4American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 3

American DJ®

Accu Scan 250™

Table of Contents

General Information.....................................................................4

Features.........................................................................5

Safety Precautions......................................................................6

Handling Precautions..................................................................7

Discharge Lamp Warnings..........................................................7

Registration......................................................................8

Controls and Functions..............................................................9

Set-Up.............................................................................12

System Menu............................................................................15

Editing Program.........................................................................28

Operating Modes.......................................................................32

Fuse and Lamp Replacement...................................................34

DMX Traits.................................................................................36

Gobos..................................................................................37

Gobo Replacement...................................................................39

Cleaning..................................................................40

Trouble Shooting.......................................................................40

Warranty.................................................................41

Specifications....................................................................43

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 5 American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 6

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible (Uses Eight DMX Channels)

• Independent Gobo and Color Wheels

• 7 Rotating Gobos w/ Shake, 1 Dichroic and 1 beveled gobo +

Spot - All Replaceable

• 9 Colors, Plus White - With Rainbow

• RDMX - Lets you set the DMX address from any DMX Controller

• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active

• Internal Microphone

• ZB-MSD250 Discharge Lamp, 250w 2000 Hours

• Edit and Save Scenes into the Memory

• Manual Focus Lens

• Variable Strobe (1-12 fps)

• 180˚ Pan Movement

• 45˚ Tilt Movement

• Digital Display for Address and Function Setting

Accu Scan 250™ Features

Accu Scan 250™ RDMX

Regarding RDMX :

1. The units will be shipped preset in 16 channel increments

from the factory

2. While using RDMX, if all units are set to the same DMX

address, all units will change to the new DMX address you

selected.

EXAMPLE: You have four units, and all the units are set to the

DMX address of “1”, and you change one unit to DMX address

“17”, this will cause all the units to change to DMX address

“17”.

All four units must be on 4 different starting addresses to indi-

vidually set the DMX addresses for each unit.

For more on this feature see pages 24-25.

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 38 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Accu Scan 250™ Safety Precautions

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 8American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 7

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Accu Scan 250™ General Instructions

The Accu Scan 250™ carries a one year limited warranty. Please fill

out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper

at the shippers cost.

Accu Scan 250™ Product Registration

Accu Scan 250™ Discharge Lamp Warning

This fixture is fitted with a discharge lamp which

is highly susceptible to damage if improperly

handled. Never touch the lamp with your bare fin-

gers as the oil from your hands will shorten lamp

life. Also, never move the fixture until the lamps

have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

This unit emits intense UV radiation which is harmful to the eyes and

skin. The intense luminance of the lamp can cause severe damage

to the retina. Never operate this unit without it’s covers, these covers

have been specially designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking

directly into the lamp at all times.

Avoid switching the ﬁxture on and off repeatedly in short intervals as

this will reduce lamp life and intensity.

To achieve the intensity associated with discharge lamps, these lamps

use gas sealed in a high pressure environment to emit a brilliant output.

Due to the high pressure involved with the construction of the lamp,

the lamp may explode during prolonged extensive use. This risk is

increased with age, added care is encouraged when dealing with older

lamps. Extreme caution should be used when operating this or any

ﬁxture ﬁtted with a gas discharge lamp. Never open this unit while in

use.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

During operation the housing may become extremely hot. Avoid touch-

ing the unit with bare hands while in use.

American DJ® will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modiﬁcation to this unit.

Accu Scan 250™ Handling Precautions

Accu Scan 250™ Controls and Functions Accu Scan 250™ Controls and Functions

1. Mirror - This is a highly reﬂective surface mirror speciﬁcally designed

to optimize and enhance beam output. Never use glass cleaners that

contain ammonia to clean the surface of the mirror (such as Windex).

2. Lens Assembly - This high quality lens is a fully focusing. Focus

the lens by manually turning the lens in a clockwise or counter-clock-

wise direction until the desired effect is achieved.

3. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

4. Mode/Esc Button - This button is used to enter the main menu and

submenus. It is also used to exit menus.

5. Up Button - This button is used to scroll forward when navigating

through the system menu.

6. Fuse Holder - This housing stores a 8 amp (4 amp 220v) GMA pro-

tective fuse. Never defeat the fuse, the fuse is designed to protect the

electronics in the event of severe power ﬂuctuations. Always be sure

to replace the fuse with an exact match as the one being replaced,

unless otherwise told to do so by an authorized American DJ® service

technician.

7. Power Cord Inlet - This unit is equipped with a removable I.E.C.

power cord. Be sure to only use the power cord included with the

unit, this cord is designed to match the electrical requirements of the

unit. Other cords may cause the unit to overheat or malfunction. Volt-

age may vary from venue to venue, when connecting this unit to a

power supply be sure to connect to a matching power outlet. Never

use this ﬁxture if the ground prong has been removed or broken off.

The ground prong is designed to reduce the risk of ﬁre or electrical

shock in the event the unit suffers from an internal short.

8. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active mode. This microphone is designed

to receive low frequency sounds only, tapping on the microphone and

high pitch sounds may not trigger the unit.

9. Mini/C Controller Jack - This jack is for use with the optional Mini/

C controller only. Do not attempt to connect an audio signal to this

jack, this will damage the PC board and void your manufactures war-

ranty!

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 9 American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 10

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 11 American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 12

Accu Scan 250™ Controls and Functions

10. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

11. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX ﬁxture, or transmit a Master/Slave signal

to the next Accu Roller 250™ in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Terminator” on page 11.

12. Lamp Assembly and Access Plate - This plate accesses the lamp

socket assembly. The unit includes a spring mounted ZB-MSD250

250w discharge lamp. Be sure to only replace with same type lamp.

After replacing a lamp be sure the lamp is centered in the reﬂector. See

page 32 for details on installing and optimizing replacement lamps.

Never operate this unit with the lamp exposed, this lamp emits strong

UV radiation.

13. Cooling Fan - This unit is equipped with three high velocity vari-

able fans to aid in the cooling process. These fans are designed to

vary their velocity at different operating temperatures, to provide

better cooling when the unit reached higher operating temperatures

associated with long usage. Be sure to never obstruct the cooling fans

during normal usage. Also, be sure to keep the vents clean at all times.

A blocked or malfunctioning cooling system may shorten lamp life and

unit reliability.

14. Down Button - This button is used to scroll backwards when navi-

gating through the system menu.

15. Enter Button - This button is used to select and conﬁrm a function

in the system menu.

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Accu Scan 250.™ The American DJ® Accu Scan 250™ is available in

a 120v and 220v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you ﬁxture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all ﬁxtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Accu Scan

250™ can be controlled via DMX-512 protocol.

The Accu Scan 250™ is a eight channel DMX unit.

The DMX address is set electronically using the

controls on the side panel of the unit. Your unit and

your DMX controller require a standard 3-pin XLR

connector for data input and data output (Figure

1). If you are making your own cables, be sure to use standard two

Accu Scan 250™ Set Up

Figure 1

conductor shielded cable (This cable may be purchased at almost all

professional sound and lighting stores). Your cables should be made

with a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Accu Scan 250™ Set Up

Notice: Be sure to follow ﬁgures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR ﬁxtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Accu Scan 250™ Set Up

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 14American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 13

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 16American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 15

Accu Scan 250™ System Menu Accu Scan 250™ System Menu

ADDRESS MENU -

AOO1 - A511 (Value) - This is where you set the DMX address of

the unit.

TEST MENU -

T-01 - T-XX (Test) - Tests the functions of each channel. There

are eight channels, but only channels 1,2,3,4, and 6 can be

tested.

AUDI MENU -

MAST (Master) - Runs the unit as master in sound active mode.

ALON (Alone) - Runs the unit stand alone, sound active mode.

RESE (RESET) MENU -

ALL - Resets all the motors in the unit.

SCAN - Resets the motors that control pan/tilt.

COLR (Color) - Resets the color motors.

GOBO - Resets the gobo motors.

SHTR - Resets the shutter motors.

TIME MENU -

LIFE - Displays the ﬁxtures total running time.

LAMP - Displays the lamp running time.

CLMP - Clears the lamp running time.

RPAN (REVERSE PAN) MENU -

ON/OFF - When “On” is chosen it will reverse the pan.

RTILT (REVERSE TILT) MENU -

ON/OFF - When “On” is chosen it will reverse the tilt.

Display menu of ACCU ROLLER 250

1 ADDR A001~A511 Indicate the staring DMX address

A001 also is the setting for slave

2 TEST T-01~T-XX Automatically test the function

MSTR Runs fixture as “master” for audio

3 AUDI

ALON Runs fixture as “alone” for audio

ALL Reset all motors and returns fixture to home

SCAN Reset only motors for pan/tilt

COLR Reset only motors for colors

GOBO Reset only motors for gobo and rotation

4 RESE

SHTR Reset only motors for shutter and/or dimmer

LIFE 0000~9999 Displays the total fixture running time

LAMP 0000~9999 Displays a lamps running time

5 TIME

CLMP Clear lamp running time

6 RPAN ON/OFF Reverses the pan movements

7 RTLT ON/OFF Reverses the tilt movements

VALU D–XX D-00 (DXXX) Display the DMX512 value of each channel

D ON ON/OFF Display turn off after 2mins

8 DISP

FLIP ON/OFF This function will reverse the dis

180

RDMX ON/OFF Change DMX address via external

controller

SPOT ON/OFF Lamp optimization

DFSE ON/OFF Resets all the fixture functions to default

9 SPEC

VER V1.0~V9.9 Software version

STEP S–01 ~S–48 Set the amount of your program

C–01 0 1 XX(00~FFH)

: :

C–30 3 0 XX(00~FFH)

TIME T – XX(01~FFH)

SCXX

CEDT ON/OFF

10 EDIT

RUN ON/OFF Pro

ram test

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 18American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 17

Accu Scan 250™ System Menu

On-Board System Menu.

The Accu Scan 250™ comes with an easy

to navigate system menu. This next section will detail the functions of

each command in the system menu.

Accu Scan 250™ System Menu

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON (Display On) - Turns digital display on and off.

FLIP - “Flips” the digital display 180º.

SPEC MENU -

RDMX - On/Off With this function you are able to change the

DMX address via external controller. See pages 25-26.

SPOT - This provides a spot beam for better lamp optimization.

DFSE - This will reset the unit to the default settings.

VER (Version) - Software version 2.2

EDIT MENU -

STEP (Step) - Steps to be used in Edit Programming. See ediit

program. See page 28.

SCO1 - SC48 (Scene 01 - Scene 48) - These are the scene slots

that you write your programs into. See edit program, pages 28

- 31.

TIME (Time) - Time for each scene. See pages 28 - 31.

CEDT - Edit program using a external controller. See pages 28

- 31.

C-01 - C-30 (Channel 1 - Channel 30) - The channels of each

scene that can be edited. See pages 28 - 31.

ADDR MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu.

2. Tap the UP button until “ADDR” is displayed, press ENTER.

3. “A001” will now be displayed. Press the UP or DOWN buttons

to ﬁnd your desired address. Press ENTER to conﬁrm.

4. The display will show “PASS”, and then display, your selected

address again.

5. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DN buttons to change the DMX start address.

TEST MENU -

TEST - This will test the functions of each channel.

1. Access the main menu.

2. Tap the UP button until “TEST” is displayed, press ENTER.

Enter Button -

To access the main menu locate the ENTER button

(15) on the front of the unit. Press this button to activate the system

menu. Tap the UP button (5) or DOWN button (14) until you reach func-

tion you wish to change. When you reach the function you wish to

change tap the ENTER button. When a function is selected the menu

will begin to ﬂash, use the UP button to change the function. Once your

changes are made tap the ENTER button again to lock the change in

the system, if the ENTER button is not selected within eight seconds

the system will automatically return to menu section. To exit without

making any changes tap the MODE/ESC button (4).

American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 20American DJ® - www.americandj.com - Accu Scan 250™ Instruction Manual Page 19

Accu Scan 250™ System Menu Accu Scan 250™ System Menu

3. The display will show “T0-1”, “1” stands for the channel

number 1, if you press the UP button until “T0-3” is displayed,

the unit will test the color channel, changing the color one by

one and showing the rainbow effect with different speeds.

4. Press MODE/ESC to exit.

AUDI MENU -

MSTR setting the unit as the master in master/slave sound

active mode.

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “MSTR” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu.

ALON in this mode the unit will run in stand alone sound

active mode.

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “ALON” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu.

LAMP MAIN MENU -

OPEN With this function you can switch the lamp on or off

via the control board.

1. Access the main menu.

2. Tap the UP button until “LAMP” is displayed, press ENTER.

3. The display will show “ON/OFF”. Press the UP button to

select “ON” to switch on the lamp, or “OFF” to switch off the

lamp.

4. Press ENTER to conﬁrm.

5. Press MODE/ESC to return to the main menu.

RESE MAIN MENU -

ALL With this function you can reset all the motors.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “ALL” is displayed.

4. Press ENTER to reset.

SCAN With this function you can reset the pan/tilt motors.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SCAN” is displayed.

4. Press ENTER to reset.

COLR With this function you can reset the color wheel

motor.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “COLR” is displayed.

Andere Handbücher für Accu Scan 250

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Mobile Beam Bedienungsanleitung

American DJ

American DJ Flash-2C Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ Atmospheric RG LED Bedienungsanleitung

American DJ

American DJ Bubble Blast Bedienungsanleitung

American DJ

American DJ FLASHBACK 4 Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

American DJ

American DJ Barrel Flex Bedienungsanleitung

American DJ

American DJ GP 250 Bedienungsanleitung

American DJ

American DJ UVLED Bar16 Bedienungsanleitung

American DJ

American DJ Flat Par QWH5 Bedienungsanleitung

American DJ

American DJ Flat Par Tri7 Bedienungsanleitung

American DJ

American DJ DMX OPERATOR DMX-512 Bedienungsanleitung

American DJ

American DJ 2.4 Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ Hyper Gem LED Bedienungsanleitung

American DJ

American DJ H2O 250 Montageanleitung

American DJ

American DJ Duo Scan RG Bedienungsanleitung

American DJ

American DJ Starball II Bedienungsanleitung

American DJ

American DJ TRI GEM LED Bedienungsanleitung

American DJ

American DJ Mini-Saucer Bedienungsanleitung

American DJ

American DJ Crusader Bedienungsanleitung

American DJ

American DJ Inno Spot Elite Bedienungsanleitung

American DJ

American DJ BU-350 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung