American DJ Inno Spot Elite Bedienungsanleitung

User Instructions

Rev. 12/13

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis-

claim any and all liabilities for property, equipment, building,

and electrical damages, injuries to any persons, and direct or

indirect economic loss associated with the use or reliance of

any information contained within this document, and/or as a

result of the improper, unsafe, unsucient and negligent as-

sembly, installation, rigging, and operation of this product.

Inno Spot Elite

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 2

• 15 DMX Channels

• 7 Colors + White

• 7 Rotating, Replaceable Gobos + Spot (6 Glass & 1 Metal Gobo)

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 4 Preprogrammed Shows

• Power Cord Daisy Chain (See page 9)

Inno Spot Elite Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting dam-

ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

Inno Spot Elite Handling Precautions

Inno Spot Elite Warranty Registration

The Inno Spot Elite carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www. adj-

products.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact ADJ Products, LLC

customer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Inno Spot Elite General Instructions

Inno Spot Elite General Information

Unpacking: Thank you for purchasing the Inno Spot Elite by ADJ

Products, LLC. Every Inno Spot Elite has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all equipment necessary to operate the unit

has arrived intact. In the event damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions. Please do not return this unit to your dealer without

contacting customer support rst.

Introduction: The Inno Spot Elite is a 15 channel, DMX intelligent,

moving head, LED fixture. The Inno Spot Elite can operate as a stand

alone fixture or in a Master/Slave configuration. The Inno Spot Elite has

three operating modes; a sound active, show mode, DMX controlled.

This fixture is suitable for theaters, studios, retail stores, and other

similar locations. For best results use fog or special effects smoke to

enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 25 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

Inno Spot Elite Safety Precautions

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 4

The Inno Spot Elite is fully operational in two dierent mounting

positions, hanging upside-down from a ceiling or set on a at level

surface. To avoid internal damage to the unit, never mount the unit on

its side as illustrated above. Be sure this xture is kept at least 0.5m

away from any ammable materials (decoration etc.). Always use

and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails (see next

page). Never use the carrying handles for secondary attachment.

When installing the unit, the trussing or area of installation must be

able to hold 10 times the weight without any deformation. When

installing the unit must be secured with a secondary safety attach-

ment, e.g. and appropriate safety cable. Never stand directly below

the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat-

ing working load limits, installation material being used, and perodic

safety inspection of all installation material and unit. If you lack these

qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

Inno Spot Elite Installation

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 7

Power Supply: The ADJ Inno Spot Elite contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into

a power source. With this switch there is no need to worry about the

correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Inno Spot Elite can be controlled via DMX-512 proto-

col. The Inno Spot Elite is a 15 channel DMX unit. The DMX address

is set electronically using the controls on the front

panel of the unit. Your unit and your DMX control-

ler require a approved DMX-512 110 Ohm Data

cable for data input and data output (Figure 1). We

recommend Accu-Cable DMX cables. If you are

making your own cables, be sure to use standard

110-120 Ohm shielded cable (This cable may be

purchased at almost all professional sound and

lighting stores). Your cables should be made with

Inno Spot Elite Set Up

Figure 1

Inno Spot Elite Installation

Screw one clamp via a M12 screw and nut onto the Omega

holder. Insert the quick-lock fasteners of the Omega holder

into the respective holes on the bottom of the Inno Spot Elite.

Tighten the quick-lock fasteners fully clockwise. Pull the safety-

cable through the safety-cable slot on the bottom of the base

and over the trussing system or a safe xation spot. Insert the

end in the carabine and tighten the safety screw.

NOTICE: The suitable enviromental temperature for this light-

ing xture is between -25˚ C to 45˚ C. Do not place this lighting

xture in an enviroment where the temperatures are under or

above the temperatures stated above. This will allow the xture

to run at its best and help prolong the xture life.

1/4 turn

turn

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Inno Spot Elite Set Up

a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Inno Spot Elite Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 4 xtures maximum for 120V and 8 xtures maxi-

mum for 240V. After the maximum xtures has been reached you

will need to use a new power outlet. They must be the same x-

tures. DO NOT mix xtures.

Inno Spot Elite Power Cord Daisy Chain

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 11

Inno Spot Elite System Menu

DMX Address - Set the DMX Address -

1. Press the MENU button until “DMX Addresss” is displayed,

press ENTER.

2. “X” will now be displayed, “X” represents the displayed

address. Press the UP or DOWN buttons to nd your desired

address.

3. Press ENTER to conrm, and then press and hold the MENU

button for at least three seconds to assign.

Show Mode - Show modes 1 - 4 (Factory Shows).

1. Press the MENU button until “Show Mode” is displayed, press

ENTER.

2. “Show X” will now be displayed, “X” representing a number

between 1-4. Press the UP or DOWN buttons to nd your desired

show and press ENTER to conrm. After pressing ENTER, press

and hold the MENU button for at least 3 seconds to activate.

SHOWS:

Show 1 - For xtures placed on the oor, the tilt movement angle is

210°

Show 2 - For fixtures fixed to the ceiling or truss, the tilt movement

angle is 90°.

Show 3 - For fixtures placed on a table or stage. The beam is pro-

jected at the audience’s direction; i.e. in front of the stage. Pan move-

ment angle (left to right to left) is 160°. Tilt movement angle is 90°.

Show 4 - For fixtures fixed to the ceiling or truss. The beam is pro-

jected at the audience’s direction; i.e. in front of the stage. Pan move-

ment angle (left to right to left) is 160°. Tilt movement angle is 90°.

Slave Mode - This will let you set unit as a slave in a

master/slave conguration.

1. Press the MENU button until “Slave Mode” is displayed,

Inno Spot Elite System Menu

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 13

ENTER.

2. Either “On” or “O” will now be displayed. Use the UP or

DOWN buttons to toggle between “On” and “O”.

3. Press ENTER to conrm your selection, the press and hold the

MENU button to activate.

Sound Sense - In this mode you can adjust the sound

sensitivity of the sound active mode.

1. Press the MENU button until “Sound Sense” is displayed,

press ENTER.

2. Press the UP or DOWN buttons to adjust the sensitivity level.

The sensitivity level can be adjusted between 0 (the lowest) and

100 (most sensitive).

3. Press ENTER to set you desired level.

Pan Inverse - Pan Inversion

1. Press the MENU button until “Pan Inverse” is displayed,

press ENTER. Either “Yes” or “No” will be displayed.

2. To activate the Pan inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

Pan inversion, select “No” and press Enter.

Tilt Inverse - Tilt Inversion

1. Press the MENU button until “Tilt Inverse” is displayed, press

ENTER. Either “Yes” or “No” will be displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

Tilt inversion, select “No” and press Enter.

Inno Spot Elite System Menu

press ENTER. Either “Slave 1” or “Slave 2” will be displayed.

2. Press the UP or DOWN buttons until your desired slave

mode is displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can make one

xture the Master and then set the next xture to “Slave 2”, the

xtures will now have contrast movement to each other.

Black Out - This mode can be used as a precaution

mode, that in case the DMX signal is lost, the operating

mode chosen in the setup is the running mode the xture will

go into when the DMX signal is lost. You can also set this as

the operating mode you would like the unit to return to when

power is applied.

1. Press the MENU button until “Black Out” is displayed, press

ENTER.

2. Either “M/S” (Master/Slave), “Hold”, or “Black Out” will be dis-

played. Choose an operating mode you would like the unit to

start up in when power is applied or the DMX signal is lost.

• M/S - If the DMX signal is lost or power is applied, the unit will

automatically go into Master Slave mode.

• Hold - If the DMX signal is lost the xture will stay in the last

DMX set up. If power is applied and this mode is set, the unit will

automatically go into the last DMX set up.

• Black Out - If the DMX signal is lost or power is applied, the unit

will automatically go into stand by mode.

3. Press ENTER to conrm your desired set up.

Sound State - In this mode the unit will run in sound

active mode.

1. Press the MENU button until “Sound State” is displayed, press

Inno Spot Elite System Menu

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 14

Back Light - With this function you can make the back-

light automatically turn off after one minute.

1. Press the MENU button until “Back Light” is displayed, press

ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or

DOWN buttons to select “ON” to keep the backlight on at all

times, or “OFF” to allow the backlight to turn o after 2 minutes.

Press any button to turn the backlight on again.

3. Press ENTER to conrm.

Focus Adjust - With this function you can adjust the

focus.

1. Press the MENU button until “Focus Adjust” is displayed,

press ENTER.

2. A number between 0-255 will be displayed. This number rep-

resents the focus setting. Use the UP or DOWN buttons to adjust

the focus to your desire.

3. When you have found your desired setting press ENTER to

conrm.

Auto Test - This function will run a self test program.

1. Press the MENU button until “Auto Test” is displayed, press

ENTER.

2. The xture will now run a self test. Press the MENU button to

exit.

Temp. - With this function you can display the running

temperature of the unit.

1. Tap the MENU button until “Temp.” is displayed, press

Inno Spot Elite System Menu

ENTER.

2. The current running temperature of the xture will now be

displayed. Press MENU to exit.

Fixture Time - With this function you can display the

running time of the unit.

1. Tap the MENU button until “Fixture Time” is displayed, press

ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

Fixture Version - This will display the software version

1. Tap the MENU button until “Fixture Version” is displayed. Press

the ENTER button and the software vesion will be displayed.

2. Press the MENU button to leave this function.

Reset - Use this function to reset the unit.

1. Tap the MENU button until “Reset” is displayed, press

ENTER.

2. The xture will now reset.

Inno Spot Elite System Menu

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 17

Inno Spot Elite System Menu

To enter the OTIL (Home position adjustment) & Gobo wheel adjust-

ment submenu, press the ENTER button for at least 3 seconds. In

this submenu you are able to adjust the home position of the pan, tilt,

color wheel, gobo wheel, RGobo (Rotating) wheel, prism, R (Rotating)

Prism, and focus position.

Pan Oset - Adjustment of the pan home position.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “Pan Offset” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Tilt Oset - Adjustment of the tilt home position.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “Tilt Offset” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Color Oset - Home setting adjustment for the color

wheel.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “Color Offset” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Gobo Oset - Home setting adjustment for the gobo

wheel.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “Gobo Offset” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

RGobo Oset - Home setting adjustment for the rotat-

ing gobo.

1. Press the ENTER button for at least 3 seconds, then press the

UP or DOWN buttons so that “RGobo Offset” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Prism Oset - Home setting adjustment for the prism.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “Prism Offset” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Inno Spot Elite System Menu

ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Inno Spot Elite Instruction Manual Page 19

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressing the ENTER button.

3. On the slave units tap the MENU button until “Slave Mode” is

displayed, and Press ENTER. Choose either “Slave 1” or “Slave

2” and press ENTER. See pages 11-12 for more info.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX controller to control the chases and patterns, dimmer

and strobe. A DMX controller allows you to create unique programs

tailored to your individual needs.

1. The Inno Spot Elite is a 15 channel DMX fixture. See pages 21-23

for detailed description of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-7 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 12 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Press the MENU button until “Sound State” is displayed, and

Inno Spot Elite Operation

RPrism Oset - Home setting adjustment for the rotat-

ing prism.

1. Press the ENTER button for at least 3 seconds, then press the

UP or DOWN buttons so that “RPrism Offset” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Focus Oset - Home setting adjustment for the focus.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “focus” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Iris Oset - Home setting adjustment for the iris.

1. Press the ENTER button for at least 3 seconds, then press the UP

or DOWN buttons so that “iris” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

Inno Spot Elite System Menu

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ X-Scan LED Plus Bedienungsanleitung

American DJ

American DJ Gobo Flash 4 Bedienungsanleitung

American DJ

American DJ Jelly Jewel LED Bedienungsanleitung

American DJ

American DJ Mobile Beam Bedienungsanleitung

American DJ

American DJ Bubble Blast Jr Bedienungsanleitung

American DJ

American DJ Penta Beam Bedienungsanleitung

American DJ

American DJ DJ Spot 250 Bedienungsanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ M-103HD Bedienungsanleitung

American DJ

American DJ Verti-Pro Bedienungsanleitung

American DJ

American DJ Stingray Bedienungsanleitung

American DJ

American DJ Super Jewel Bedienungsanleitung

American DJ

American DJ S-1500/DMX Bedienungsanleitung

American DJ

American DJ LED Messenger Bedienungsanleitung

American DJ

American DJ Galaxian Move Bedienungsanleitung

American DJ

American DJ DJ Roller Bedienungsanleitung

American DJ

American DJ Festive Light Pak II Bedienungsanleitung

American DJ

American DJ Raider Bedienungsanleitung

American DJ

American DJ Onyx II Bedienungsanleitung

American DJ

American DJ Crusader Bedienungsanleitung

American DJ

American DJ Reflex Bedienungsanleitung

American DJ

American DJ Color Burst LED Bedienungsanleitung

American DJ

American DJ WiFly Par QA5 WH Bedienungsanleitung

American DJ

American DJ BU-350 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung