American DJ DJ Scan 250 Bedienungsanleitung

User Instructions

American DJ

4295 Charter Street

Los Angeles, CA 90058

www.americandj.com

DJ Scan 250™ Introduction

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 2

Introduction: Congratulations and thank you for purchasing the DJ

Scan 250™ by American DJ®, one of the finest pieces of its kind on the

market today! The DJ Scan 250™ is a great inexpensive, light weight,

intelligent fixture. Due to it’s physical specifications, it’s a great piece

for mobile DJ’s, roller rinks, small clubs, bars, and bowling centers.

When used in multiples of two or more, these units create an effect

that rivals that of units that can cost up to three times the price. The DJ

Scan 250™ was designed to run in a Master/Slave mode but can be

used with any universal DMX-512 controller.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set-up and installation help and to answer any

question should you encounter problems during your set up or initial

operation. You may also visit us on the web at www.americandj.com

for any comments or suggestions. Toll free customer service hours are

Monday through Friday 9:00 a.m. to 5:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ® customer support.

Do not discard the shipping carton in the trash. Please recycle when

ever possible.

Improvements and changes in specications and design to this

manual and unit may be made at any time without prior notice.

HALOGEN LAMP WARNING!

This fixture is fitted with a halogen lamp which is highly susceptible to

damage if improperly handled. Never touch the lamp with your bare

fingers as the oil from your hands will shorten the lamp life. Never

install, mount, or place this fixture in areas prone to heavy vibration.

Also, never move the fixture until the lamp has had ample time to

cool. Remember, lamps are not covered under warranty conditions.

7/03

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 4©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 3

DJ Scan 250™ Quick Start

The DJ Scan 250™ features a bright 250 watt halogen bulb with a

separate gobo and color wheel. The color wheel features seven bril-

liant colors plus white and the gobo wheel features 10 gobos plus

a large spot. This fixture incorporates the use of high quality step-

per motors for a more accurate mirror movement. Mirror movement

allows for a full 90 degree tilt (vertical) and a 45 degree pan (hori-

zontal). An internal built in microphone allows the fixtures to run in

Stand Alone mode so there is no need for an external controller. The

DJ Scan 250™ may also be set-up to run in a Master-Slave mode

when used in multiples, up to four units. When used in the Master-

Slave mode, the unit will chase to several internal programs. The

DJ Scan 250™ can also be controlled via a standard DMX control-

ler such as the American DJ® Show Designer,™ or the American

DJ® DMX Operator,™ giving the user independent control over the

gobo and color wheel as well as the mirrors pan and tilt movements.

Note: The built in programs in the DJ Scan 250™ are so good you

may never need a DMX controller.

• ZB-ELC7 24V/250W

• DMX-512 Compatible.

• Stepper motors for smooth movements.

• 7 colors plus white.

• 10 Gobos plus spot.

• Gobo Shake

• Master/Slave Operation

• Sound Active.

• Optional MINI/C controller, for blackout control.

• Optional Wireless MINI/C controller, for blackout control.

DJ Scan 250™ Features

Master/Slave Quick Start Stand Alone Mode

Connect up to four units together via XLR cables. The master unit will

run the slaves to the masters built in programs and internal micro-

phone. Plug in all units. When the DJ Scan 250™ is first turned on, it

will run through an internal self test where it resets all motors to their

zero position. After the self test the units will react to sound, and fol-

low several built in programs.

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Please route your power cord out of the way of

foot trafc.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the top cover under any conditions. There are no

user serviceable parts inside.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged in any

way.

• Never operate this unit when it’s cover is removed.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• This unit is intended for indoor use only, use of this product out

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power Cord Protection - Power cords should be routed so they are

not likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs, conve-

nience receptacles, and the point where they exit from the unit.

• Cleaning - Follow the directions on page 10.

• Heat -The unit should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

DJ Scan 250™ Safety Precautions

Unpacking:

Every DJ Scan 250™ has been thoroughly tested and has been shipped

in perfect operating condition, there is no assembly necessary. Care-

fully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect

your unit for any damage and be sure all equipment necessary to oper-

ate the unit has arrived intact. In case damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions, please do not return the unit to your dealer.

Power Supply:

Before plugging your unit in be sure the source voltage in your area

matches the required voltage for your American DJ® DJ Scan 250.™

The American DJ® DJ Scan 250™ is available in a 120v and 220v ver-

sion. Because line voltage may vary from venue to venue, you should

be sure to plug your unit into a matching wall outlet before attempting

to operate you controller.

Data Cable (DMX Cable) Requirements:

Your controller and packs require a standard 3-pin XLR connector for

DMX data input and DMX data output (Figure 1). If you are making your

own cables be sure to use standard two conductor shielded cable (This

cable may be purchased at almost all pro sound and lighting stores).

Your cables should be made with a male and female XLR connector on

either end of the cable. Also remember that DMX cable must be daisy

chained and can not be “Y-d” or split.

Notice: Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX +

DMX -

COMMON

DMX512 IN

CONNECTOR

3 PIN

DMX512 OUT

CONTROLLER

CONNECTOR

3 PIN

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 5

DJ Scan 250™ Set Up

Figure 2

DJ Scan 250™ Set Up

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 6

Notice: Be sure to follow gures two and three when making your own

cables.

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm

1/4 watt resistor which is connected between pins 2 and 3 of a male

XLR connector (DATA - and DATA +). This unit is inserted in the female

XLR connector of the last unit in your daisy chain to terminate the

line. Using a cable terminator will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

DJ Scan 250™ DMX Addressing

DMX CHANNEL

1 2 3 54 7 986

1 4 16 64 256

2 8 32 128

DMX is short for Digital Multiplex. This is a universal binary language

used as a form of communication between intelligent fixtures. Each

dipswitch represents a binary value.

Dipswitch 1 address equals 1

Dipswitch 2 address equals 2

Dipswitch 3 address equals 4

Dipswitch 4 address equals 8

Dipswitch 5 address equals 16

Dipswitch 6 address equals 32

Dipswitch 7 address equals 64

Dipswitch 8 address equals 128

Dipswitch 9 address equals 256

Figure 3

4. Turn the master unit dipswitchws to the “Off” position.

5. Please follow chart on page 13 for all slave dipswitch settings.

Note only one fixture may use the master units dipswitch set-

tings (see Page 13).

6. After all the units settings have been set and are plugged in,

adjust the sensitivity knob on the bottom of the master unit to

make them react to sound.

7. To run a synchronized light show set all the dipswitch on all the

fixture to the ‘off’ position. All fixtures will now run in the same

exact pattern.

8. You can also use the optional MINI/C Remote Control. If you want

to use the optional remote control, connect the MINI/C controller

to the first fixture in the line (master).

Note: The remote control only operates in Stand-Alone and Master/

Slave modes. If the remote is connected in DMX mode it will not func-

tion. If the units do not receive an active DMX signal, the units will

automatically react to sound in the Master/Slave mode.

DMX Mode:

This fixture will react with DMX operation. For best results use only

one motor function for each scene (or step), when programming

scenes into a DMX controller. This will give you faster mirror and fast-

er gobo/color changes. For Example:

A. With the DMX controller move the mirror up then program the

step.

B. Move the mirror down then program that step.

C. Change the gobo/color wheel then program that step.

D. Continue this pattern to achieve best results.

1. Operating through a DMX controller gives the user freedom to

create his/her own programs tailored to their own individual

needs. This function also allows you to use your fixtures as spots.

2. This operation will allow you to control each individual fixtures

traits with a standard DMX 512 controller such as the

American DJ Show Designer™ or the American DJ® DMX

Operator.™

3. The DJ Scan 250™ uses four DMX channels to operate; Channel1

is Pan, channel 2 is Tilt, channel 3 is Color, and channel 4 Gobos.

4. To run your fixture in DMX mode, plug in the fixture via the XLR

DJ Scan 250™ Operating Instructions DJ Scan 250™ Operating Instructions

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 8©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 7

Operating Modes:

You can use the DJ Scan 250™ in three ways:

• Stand alone mode - The unit will react to sound, chasing through

the several built in programs. You can also use the optional DJ Scan

MINI/C Remote Control to blackout the units.

• Master/Slave mode - You can daisy chain up to 4 units together

toget a synchronized light show that will react to sound chasing

through several built in programs.

• DMX control mode - This function will allow you to control each

individual fixtures traits with a standard DMX 512 controller such as

the American DJ Show Designer.™

For best results use fog or special effects smoke to enhance the

beams projections. The DJ Scan 250™ comes with a protective

transportation cover. Be sure to remove it before attempting any

operation!

Stand Alone Mode:

1. To operate as a stand alone unit, via its internal chases and

microphone, turn all dipswitches off.

2. Adjust the sensitivity knob on the bottom of the unit so the unit

will react to sound.

3. The DJ Scan 250™ will now react to the bass sound of music via

the internal microphone.

Master-Slave Operation:

This function will allow you to link up to 16 units together to run on

the master unit’s 2 channel internal programs. In Master-Slave opera-

tion one unit will act as the controlling unit and the others will react to

the controlling units programs. Any unit can act as a Master or as a

Slave.

1. Daisy chain your units via the XLR connector on the bottom

of the units.

2. Use standard XLR microphone cables to link your units together.

Remember that the Male XLR connector is the input and the

Female XLR connector is the output.

3. The first unit in the chain (master) will use the female XLR connec-

tor only - The last unit in the chain will use the male XLR connec

tor only.

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 10©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 9

DJ Scan 250™ Lamp Replacement

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power before attempting to replace the

lamp.

1. Be sure to follow the proper procedures when handling halogen

bulbs.

2. Lamp replacement has been made simple by incorporating the use

of a removable lamp tray and thumb screws.

3. Loosen the thumb screw on rear cover.

4. Remove the tray.

5. Remove and replace the bulb.

6. Reassemble.

Remember to always replace with the exact same type lamp and

fuse, unless otherwise specified by an authorized American DJ

service technician.

The DJ Scan 250™ may be controlled by a wide range of controllers;

ie. Show Designer™, DMX Operator,™ Scene Setter™ or by the DJ

MINI/C basic controller.

MINI/C features:

DJ Scan 250™ Optional Remote

The MINI/C controller may be purchased separately allowing you to

control the main unit, and any others connected to it, while it is in

stand alone mode. You can set the unit to blackout. If you have more

than one unit, make sure the remote control is plugged into the first

unit in the daisy chain. The remote control will not have any effect if

the unit is in DMX mode. When the unit is in blackout mode, the light

will come on next to the blackout button.

30 ft. cable

Stand by (Black out)

DJ Scan 250™ Operating Instructions

connections to any standard DMX controller. Set dipswitch #1 to

the on position - Follow the set-up specifications that come with

the controller.

DJ Scan 250™ Focusing

1. To focus a DJ Scan 250,™ it is best to first turn down the music

sensitivity knob to its minimum position.

2. Loosen the thumb screw on the front of the unit that hold the lens

in place.

3. Adjust the focus by manually moving the lens up and down.

4. Tighten the thumb screw after you achieve your desired focus.

Listed below are a few common problems the user may encounter,

with solutions.

No light from the unit;

1. Check if the ‘Power On’ (red) LED is lit and the fan is running. If

not, there is no main power supply.

2. Check the fuse in the back panel.

3. Check if lamp is lit. The user should be able to see some light

escape through the fan. If power is present but the lamp is not lit,

lamp may need to be replaced.

Note: The unit has been designed to shut the lamp down after 60 sec-

onds of inactivity. This is a way of extending lamp life, be assured this

is not the problem with the fixture.

Unit not responding to DMX;

1. If the Green LED on the top of the unit is flashing, the unit is

definitely receiving DMX

2. Check the dipswitch settings.

3. If the DMX LED is not lit, check that the DMX cables are con-

nected properly and are wired correctly (pin 3 is ‘hot’; on some

other DMX devices pin 2 may be ‘hot’). Also, check that all cables

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 12©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 11

DJ Scan 250™ Trouble Shooting

DJ Scan 250™ Trouble Shooting Cont.

The DJ Scan 250™ carries a one year (365 days) limited warranty. We

recommend you fill out the enclosed warranty card to validate your

purchase. All returned service items whether under warranty or not,

must be freight pre-paid and accompany a return authorization (R.A.)

number. If the unit is under warranty, you must provide a copy of your

proof of purchase invoice. Please contact American DJ® customer

support for a R.A. number.

DJ Scan 250™ Product Registration

are connected to the right connectors; it does matter which way

the inputs and outputs are connected.

4. If it is a bad connection, the Green LED may flash when cables are

wiggled (but remember it may also be the unit sensing audio!)

5. If DMX connectors are fairly short, ordinary microphone cables

may be used. For longer runs, this may cause data transmission

problems (which will show up as random or incorrect movements)

for best result, use proper balanced data transmission cable.

Unit does not respond to sound;

1. Check to see if the unit is receiving DMX (the green LED should

be off).

2. Tapping the microphone should cause the LED to flash (quiet

or high pitched sounds will not activate the unit). If the red LED

does not flash to sound there may be an internal problem.

3. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

Unit blacks out in stand alone mode;

1. Some of the units’ built-in patterns include special effects such

as blackout sweeps.

2. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

If problems are not resolved; Contact your American DJ® customer

support for possible service options.

Due to fog residue, smoke, and dust, cleaning the internal and exter-

nal optical lenses must be carried out periodically to optimize light

output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days. Situation may very. If used heavily in clubs with lots of

fog, cleaning may be required more often.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the

unit in.

Cleaning frequency depends on the environment in which the fixture

operates (i.e. smoke, fog residue, dust, dew).

DJ Scan 250™ Cleaning

DJ Scan 250™ Master/Slave Settings DJ Scan 250™ DMX Traits

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 14©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 13

Channel Value Function

1 0 - 255 PAN

2 0 - 255 TILT

3 0 - 139 COLOR

0 - 28 LAMP OFF

29 - 57 WHITE

58 - 86 RED

87 - 115 BLUE

116 - 144 YELLOW

145 - 173 GREEN

174 - 202 ORANGE

203 - 231 PINK

232 - 255 PURPLE

4 GOBO

0 - 6 SPOT

7 - 21 SPOT SHAKE

22 - 28 GOBO 1 (metal)

29 - 43 GOBO 1 SHAKE

44 - 50 GOBO 2 (metal)

51 - 65 GOBO 2 SHAKE

66 - 72 GOBO 3 (dichroic)

73 - 87 GOBO 3 SHAKE

88 - 94 GOBO 4 (metal)

95 - 109 GOBO 4 SHAKE

110 - 116 GOBO 5 (metal)

117 - 131 GOBO 5 SHAKE

132 - 138 GOBO 6 (metal)

139 - 153 GOBO 6 SHAKE

154 - 160 GOBO 7 (metal)

161 - 175 GOBO 7 SHAKE

176 - 184 GOBO 8 (metal)

219

Head 2

Head 4

Head 3

Head 15

Head 11

Head 14

Head 10

Head 9

Head 13

Head 7

Head 6

Head 5

Head 16

Head 12

Head 8

Head 1

128

The following details the proper dipswitch setting for Master-Slave

operation. Please follow these setting when running four or more units

in a Master-Slave conguration.

DJ Scan 250™ DMX Traits

Channel Value Function

4 185 - 197 GOBO 8 SHAKE

198 - 204 GOBO 9 (metal)

205 - 219 GOBO 9 SHAKE

220 - 226 GOBO 10 (metal)

227 - 241 GOBO 10 SHAKE

242 - 248 BLACK OUT

249 - 255 BLACK OUT SHAKE

©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 16©American DJ Supply® - www.americandj.com - DJ Scan 250™ Instruction Manual Page 15

DJ Scan 250™ Warranty

1-YEAR LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)

from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than

the American DJ® factory unless prior written authorization was issued to purchaser by

American DJ®; if the product is damaged because not properly maintained as set forth in

the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ® will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this war-

ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, includ-

ing warranties of merchantability or tness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of

merchantability or tness, shall apply to this product after said period has expired. The

consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. All lamps and fuses are not covered under this warranty.

DJ Scan 250™ Gobo Layout

GOBO 1

GOBO 7GOBO 6

GOBO 5GOBO 4GOBO 3GOBO 2

GOBO 10GOBO 9GOBO 8

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

Specifications: DJ Scan 250™

Weight: 12 Lbs.

Dimensions: 18” (L) x 8.6” (W) x 4.3” (H)

Lamp: ZB-ELC 24v-250w

Fuse: 120v = 5A GMA

220v = 3A GMA

Voltage*: 120v/220v, 60Hz/50Hz

Gobos: 10 Plus Spot

Colors: 7 Plus White

Cooling: Fan Cooled

Working Position: Any Safe Position

* Operating voltage is preset at the factory.

Please Note: Specications and improvements in the design of

this unit and this manual are subject to change without any prior

written notice.

Andere Handbücher für DJ Scan 250

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Charisma II Bedienungsanleitung

American DJ

American DJ BU-200 Bedienungsanleitung

American DJ

American DJ Gobo Flash 4 Bedienungsanleitung

American DJ

American DJ Sunray Tri LED DMX Bedienungsanleitung

American DJ

American DJ Festive Light Pak II Bedienungsanleitung

American DJ

American DJ Punch LED PRO Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

American DJ

American DJ H2O Bedienungsanleitung

American DJ

American DJ Flash Duo Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ Bubble Blast Jr Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ Fire Bowl Bedienungsanleitung

American DJ

American DJ Rover Bedienungsanleitung

American DJ

American DJ LED Messenger Bedienungsanleitung

American DJ

American DJ H2O 250 Montageanleitung

American DJ

American DJ Razz Mataz Bedienungsanleitung

American DJ

American DJ Color Shot Bedienungsanleitung

American DJ

American DJ Tempest 575H Bedienungsanleitung

American DJ

American DJ Revo Burst Bedienungsanleitung

American DJ

American DJ Fan-1000 Bedienungsanleitung

American DJ

American DJ X-Treme/19C Montageanleitung

American DJ

American DJ S-1500/DMX Bedienungsanleitung

American DJ

American DJ Starball II Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung