American DJ Accu Spot 250 II Bedienungsanleitung

American DJ®

6122 S. Eastern Ave.

Los Angeles CA. 90040

www.americandj.com

Rev. 9/08

User Instructions

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 2

American DJ®

Accu Spot 250 II™

Table of Contents

Unpacking......................................................................3

Introduction....................................................................3

Customer Support......................................................................3

Safety Precautions......................................................................4

Features.........................................................................5

RDMX..........................................................................................5

Handling Precautions..................................................................6

Discharge Lamp Warnings..........................................................6

Registration......................................................................7

Controls and Functions...............................................................8

Set-Up.............................................................................11

System Menu............................................................................14

Editing Program.........................................................................31

Operating Modes.......................................................................36

Lamp Replacement...................................................................38

Lamp Alignment and Fuse Replacement...............................39

DMX Traits.................................................................................40

Gobos..................................................................................41

Gobo Replacement...................................................................46

Opitional Lens...........................................................................47

Cleaning..................................................................48

Trouble Shooting.......................................................................48

Warranty.........................................................................49

Specifications....................................................................51

Unpacking: Thank you for purchasing the Accu Spot 250 II™ by

American DJ®. Every Accu Spot 250 II™ has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The Accu Spot 250 II™ is a eight channel or nine chan-

nel, moving head, intelligent DMX fixture. The fixture can operate in

three different operating modes; stand alone, sound-active, or in a

Master/Slave configuration. The Accu Spot 250 II™ comes with sev-

eral built in programs and is best used in multiples of four. When used

as a stand alone unit or when used in multiples linked in a master/

slave configuration. For best results use fog or special effects smoke

to enhance the beams projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the lamp.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Accu Spot 250 II™ General Information

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 48 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Accu Spot 250 II™ Safety Precautions

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 4American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 3

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• 2 Modes of DMX-512 Protocol Compatible (Eight DMX Channel

Mode or Nine DMX Channel Mode)

• Independent Gobo and Color Wheels

• 7 Rotating Gobos, 2 Dichoric + Spot - All Replaceable

• 9 Colors, Plus White - With Rainbow

• RDMX - Lets you set the DMX address from any DMX Controller

• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active

• Internal Microphone

• ZB-MSD250 Discharge Lamp, 230v/250w

• Edit and Save Scenes into the Memory

• Manual Focus Lens

• 360˚ Pan Movement

• 265˚ Tilt Movement

• Digital Display for Address and Function Setting

Accu Spot 250 II™ Features

Accu Spot 250 II™ Discharge Lamp Warning

This fixture is fitted with a discharge lamp which

is highly susceptible to damage if improperly

handled. Never touch the lamp with your bare fin-

gers as the oil from your hands will shorten lamp

life. Also, never move the fixture until the lamps

have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

This unit emits intense UV radiation which is harmful to the eyes and

skin. The intense luminance of the lamp can cause severe damage

to the retina. Never operate this unit without it’s covers, these covers

have been specially designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking

directly into the lamp at all times.

Avoid switching the xture on and off repeatedly in short intervals as

this will reduce lamp life and intensity.

To achieve the intensity associated with discharge lamps, these lamps

use gas sealed in a high pressure environment to emit a brilliant output.

Due to the high pressure involved with the construction of the lamp,

the lamp may explode during prolonged extensive use. This risk is

increased with age, added care is encouraged when dealing with older

lamps. Extreme caution should be used when operating this or any

xture tted with a gas discharge lamp. Never open this unit while in

use.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ®.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Accu Spot 250 II™ Handling Precautions

Accu Spot 250 II™ RDMX

Regarding RDMX :

1. The units will be shipped preset in 16 channel increments

from the factory

2. While using RDMX, if all units are set to the same DMX

address, all units will change to the new DMX address you

selected.

EXAMPLE: You have four units, and all the units are set to the

DMX address of “1”, and you change one unit to DMX address

“17”, this will cause all the units to change to DMX address

“17”.

All four units must be on 4 different starting addresses to indi-

vidually set the DMX addresses for each unit.

For more on this feature see pages 26-27.

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 6American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 5

Accu Spot 250 II™ Controls and Functions

REAR

FRONT

1 3

1 2

1 4

1 5

1 2

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 7

The Accu Spot 250 II™ carries a one year limited warranty. Please fill

out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper

at the shippers cost.

Accu Spot 250 II™ Product Registration

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 8

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Accu Spot 250 II™ General Instructions

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 10American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 9

Accu Spot 250 II™ Controls and Functions

1. Lens Assembly - This high quality lens is a fully focusing. Focus

the lens by manually turning the lens in a clockwise or counter-clock-

wise direction until the desired effect is achieved.

2. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

3. Mode/Esc Button - This button is used to enter the main menu and

submenus. It is also used to exit.

4. Up Button - This button is used to scroll forwards when navigating

through the system menu.

5. Down Button - This button is used to scroll backwards when navi-

gating through the system menu.

6. Enter Button - This button is used to select and conrm a function

in the system menu.

7. Carrying Handles - The includes built-in carrying handles. Be sure

to always handle the unit by the built-in handles. Never lift or carry-

ing the unit by head or yoke. Pulling on or transporting the unit by the

moving head may severely damage the unit and will void the unit war-

ranty.

8. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX xture, or transmit a Master/Slave signal

to the next Accu Spot 250 II™ in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Line Termination” on page 12.

9. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

10. Mini/C Controller Jack - This jack is for use with the optional

Mini/C controller only. Do not attempt to connect an audio signal to

this jack, this will damage the PC board and void your manufactures

warranty!

11. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active mode. This microphone is designed

to receive low frequency sounds only, tapping on the microphone and

high pitch sounds may not trigger the unit.

Accu Spot 250 II™ Controls and Functions

12. Cooling Fan - This unit is equipped with three high velocity vari-

able fans to aid in the cooling process. These fans are designed to

vary their velocity at different operating temperatures, to provide

better cooling when the unit reached higher operating temperatures

associated with long usage. Be sure to never obstruct the cooling fans

during normal usage. Also, be sure to keep the vents clean at all times.

A blocked or malfunctioning cooling system may shorten lamp life and

unit reliability.

13. Lamp Assembly and Access Plate - This plate accesses the lamp

socket assembly. The unit includes a spring mounted ZB-MSD250

230v/250w discharge lamp. Be sure to only replace with same type

lamp. After replacing a lamp be sure the lamp is centered in the reec-

tor. See pages 38-39 for details on installing and optimizing replace-

ment lamps. Never operate this unit with the lamp exposed, this lamp

emits strong UV radiation.

14. Fuse Holder - This housing stores a 8 amp (4 amp 220v) GMA pro-

tective fuse. Never defeat the fuse, the fuse is designed to protect the

electronics in the event of severe power uctuations. Always be sure

to replace the fuse with an exact match as the one being replaced,

unless otherwise told to do so by an authorized American DJ®service

technician.

15. Power Cord Inlet - This unit is equipped with a removable I.E.C.

power cord. Be sure to only use the power cord included with the

unit, this cord is designed to match the electrical requirements of the

unit. Other cords may cause the unit to overheat or malfunction. Volt-

age may vary from venue to venue, when connecting this unit to a

power supply be sure to connect to a matching power outlet. Never

use this xture if the ground prong has been removed or broken off.

The ground prong is designed to reduce the risk of re or electrical

shock in the event the unit suffers from an internal short.

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 11 American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 12

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Accu Spot 250 II.™ The American DJ®Accu Spot 250 II™is available

in a 120v and 220v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you xture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Accu Spot 250

II™ can be controlled via DMX-512 protocol. The

Accu Spot 250 II™ can be a eight or nine channel

DMX unit. The DMX address is set electronically

using the controls on the side panel of the unit.

Your unit and your DMX controller require a standard

3-pin XLR connector for data input and data output

(Figure 1). We recommend Accu-Cable DMX cables. If you are making

Accu Spot 250 II™ Set Up

Figure 1

your own cables, be sure to use standard 110-120 Ohm shielded cable

(This cable may be purchased at almost all pro lighting stores). Your

cables should be made with a male and female XLR connector on

either end of the cable. Also remember that DMX cable must be daisy

chained and cannot be split.

Accu Spot 250 II™ Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 13

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Accu Spot 250 II™ Set Up

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 14

Accu Spot 250 II™ System Menu

ADDR

AXXX A001

Indicate the staring DMX address

A001 also is thesettingfor slave

TEST

T-01~T-XX

Automatically testthe function

RUN

MSTR/ALON

Runs xture as “master” or “alone” for auto

AUDI

MSTR/ALON

Runs xture as “master” or “alone” for audio

PLA Y

AUT O

OFF / RUN /AUDI

Runs xture for no DMX

LAMP

ON/OFF

Manually switches lamp “on” and “off”

ALL

Reset all motorsand returns xture to home

SCAN

Reset only motorsfor pan/tilt

COLR

Reset only motorsfor colors

GOBO

Reset only motors for goboand rotation

RESE

SHTR

Reset only motorsfor shutterand/ordimmer

LIFE

0000~9999

Displays thetotal xture running time

LAMP

0000~9999

Displays a lamps runningtime

TIME

CLMP

Clear lamp runningtime

RPAN

ON/OFF

Reverses thepan movements

RTL T

ON/OFF

Reverses thetilt movements

MIC

M-XX

Mic sensitivity

VALU

D–XX D-00 (DXXX)

Display theDMX512 value of each channel

D ON

ON/OFF

Display turn off after 2mins

DISP

FLIP

ON/OFF

This function will reverse the display 180

LAAU

ON/OFF

Automatic lamp start with power

RDMX

ON/OFF

Change DMX addressvia external controller

MODE

8 CH/9 CH

Channel modeselect

DLOF

ON/OFF

Switch lamp via DMX

DLA Y

D–XX D-05

Lamp on delay time

SPOT

ON/OFF

Lamp optimization

DFSE

ON/OFF

Resets all thexture functions to default

FEED

ON/OFF

Pan/tilt feedback (error correction) on/off

VER

V1.0~V9.9

Software version

CODE

CXXX

Fixture code *code is “C050”

SPEC

ADJU

CH01~CH30

XXXX(-128~127)

Motor Calibration

STEP

S–01 ~S–48

Set theamountof your program

C–01~C–30

0 1 XX(00~FFH)

3 0 XX(00~FFH)

Edit the channelsof each scene

TIME

T XXX(001~999)

Time for each scene

SCXX

CEDT

ON/OFF

Edit programvia controller

REC.

RE.XX

Auto Save

EDIT

RUN

ON/OFF

Program test

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 16American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 15

Accu Spot 250 II™ System Menu

ADDRESS MENU -

A001 - A511 - This is where you set the DMX address of the unit.

TEST MENU -

T-01 - T-XX - Tests the functions of each channel. There are

eight channels, but only channels 1,2,3,4, and 6 can be tested.

PLAY MENU -

RUN - Runs the unit as a “master” in a Master/Slave congura-

tion or as a Stand Alone unit. The unit will run a internal pro-

gram.

AUDI (Audio) - Runs the unit as a “master” in a Master/Slave

conguration or as a Stand Alone unit in sound active mode.

AUTO - This is a precaution mode in case the DMX signal is lost.

There are four settings to choose from:

• “Off” - This is the default setting, which in case the signal is

lost the xture will “hold” at the last setting.

• “Run” - The xture will go into Auto mode and run a pre-pro-

grammed show.

• “Audi” - The xture will go into Sound Active mode.

AUDI MENU -

ALON (Alone) - Unit runs in stand alone mode, no master/slave.

MAST (Master) - Designates that unit to be master in master/

slave mode.

LAMP MENU -

ON/OFF - Manually switches the lamp “On” or “Off”.

RESE (RESET) MENU -

ALL - Resets all motors.

SCAN - Resets the pan/tilt motors.

COLR (Color) - Resets the color wheel motor.

GOBO - Resets the gobo wheel motor.

SHTR (Shutter) - Resets the shutter and dimmer motors.

TIME MENU -

LIFE - Displays the total xture running time.

LAMP - Displays the lamp running time.

CLMP - Clears the lamp running time.

RPAN MENU -

ON/OFF - Reverses the pan.

RTLT MENU -

ON/OFF - Reverses the tilt.

MIC MENU -

M-01-M-70 - With this function you can make the internal mic

more or less sensitive to sound.

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON - Turns digital display off after 2 minutes.

FLIP - “Flips” the digital display 180º.

SPEC MENU -

LAAU - On/Off Automatically switches on lamp when power is

applied.

RDMX - On/Off With this function you are able to change the

DMX address via external controller. See pages 26-27.

MODE - 8Ch/9Ch With this function you can switch between 8

channels and 9 channels. See pages 40-42 for the 8 Channel

mode DMX traits, and 43-45 for 9 Channel mode DMX traits.

Accu Spot 250 II™ System Menu

On-Board System Menu.

The Accu Spot 250 II™ comes with an

easy to navigate system menu. This next section will detail the func-

tions of each command in the system menu.

Enter Button -

To access the main menu locate the ENTER button (6)

on the front of the unit. Press this button to activate the system menu.

Tap the UP button (4) until you reach function you wish to change.

When you reach the function you wish to change tap the ENTER button.

When a function is selected the menu will begin to ash, use the UP

button to change the function. Once your changes are made tap the

ENTER button again to lock the change in the system, if the ENTER

button is not selected within eight seconds the system will automati-

cally return to menu section. To exit without making any changes tap

the MODE/ESC button (3).

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 18American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 17

ADDR MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu.

2. Tap the UP button until “ADDR” is displayed, press ENTER.

3. “A001” will now be displayed. Press the UP or DOWN buttons

to nd your desired address. Press ENTER to conrm.

4. The display will show “PASS”, and then display, your selected

address again.

5. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DN buttons to change the DMX start address.

TEST MENU -

TEST - This will test the functions of each channel.

1. Access the main menu.

2. Tap the UP button until “TEST” is displayed, press ENTER.

Accu Spot 250 II™ System Menu

DLOF (Lamp Adjustment) - With this function you can adjust the

lamp via the control board. In this mode, the device will not

react to any control signal.

DLAY - With this function you can put the lamp on a delay time.

SPOT - This provides a spot beam for better lamp optimization.

DFSE - This will reset the unit to the default settings.

FEED - With this function you can activate or deactivate the

pan/tilt error correction. So if you units head gets knocked out

of place the unit will automatically go back to the last setting.

VER - This will display the software version

ADJU - Fixture code is “C050”.

CH01~CH30 for motor calibration.

EDIT MENU -

STEP (Step) - Steps to be used in Edit Programming. See ediit

program. See page 31.

SCXX (SC01 - SC30) - These are the scenes that are stored in

your program. There are a total of 30 scenes.

Submenus:

C-01~C-30 - Edit the channels of each scene.

TIME - Set the Time for each scene.

CEDT - Edit the program via external controller.

REC - This will auto save your custom program.

RUN - This will run your custom program.

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 20

Accu Spot 250 II™ System Menu

American DJ®- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 19

3. Tap the UP button until “AUTO” is displayed, press ENTER.

4. Now you can choose between “CLOSE”, “HOLD” “AUTO”, or

“AUDI”. “HOLD” is the default setting.

5. Select the mode that you want the xture to run in case of a

lost DMX signal and press ENTER.

LAMP MAIN MENU -

OPEN With this function you can switch the lamp on or off

via the control board.

1. Access the main menu.

2. Tap the UP button until “LAMP” is displayed, press ENTER.

3. The display will show “ON/OFF”. Press the UP button to

select “ON” to switch on the lamp, or “OFF” to switch off the

lamp.

4. Press ENTER to conrm.

5. Press MODE/ESC to return to the main menu.

RESE MAIN MENU -

ALL With this function you can reset all the motors.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “ALL” is displayed, press ENTER.

4. Press ENTER to reset.

5. Press MODE/ESC to return to the main menu.

3. The display will show “T0-1”, “1” stands for the channel

number 1, if you press the UP button until “T0-3” is displayed,

the unit will test the color channel, changing the color one by

one and showing the rainbow effect with different speeds.

4. Press MODE/ESC to exit.

AUDI MENU -

MSTR setting the unit as the master in master/slave sound

active mode.

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “MSTR” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu.

ALON in this mode the unit will run in stand alone sound

active mode.

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “ALON” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu.

AUTO This is a precaution mode in case you lose the DMX

signal. The xtue has 4 modes to choose from, please see

page 15 for a description of the 4 modes -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

Accu Spot 250 II™ System Menu

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ LED Beam Scan Bedienungsanleitung

American DJ

American DJ Majestic LED Bedienungsanleitung

American DJ

American DJ X-CALIBUR Bedienungsanleitung

American DJ

American DJ Shooting Star LED Bedienungsanleitung

American DJ

American DJ Flash-1C Bedienungsanleitung

American DJ

American DJ Revo Roll LED Bedienungsanleitung

American DJ

American DJ Mighty Scan Bedienungsanleitung

American DJ

American DJ Flight-Moon Bedienungsanleitung

American DJ

American DJ Flash Duo Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Mega Bar LED Bedienungsanleitung

American DJ

American DJ Gobo Motion LED Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ Flat Par QWH5 Bedienungsanleitung

American DJ

American DJ Galaxian Royale Bedienungsanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ SCENE SETTER Bedienungsanleitung

American DJ

American DJ PDP-800 Bedienungsanleitung

American DJ

American DJ Razz Mataz Bedienungsanleitung

American DJ

American DJ Sunray-150D Bedienungsanleitung

American DJ

American DJ Reflex LED Bedienungsanleitung

American DJ

American DJ VioROLL LED Bedienungsanleitung

American DJ

American DJ Flash-2C Bedienungsanleitung

American DJ

American DJ Eco UV Bar DMX Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung