American DJ DJ Spot 250 Bedienungsanleitung

American DJ

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Rev. 9/04

User Instructions

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 2

DJ Spot 250™

Table of Contents

General Instructions....................................................................2

Customer Support.......................................................................3

Safety Precautions......................................................................4

Features.........................................................................5

Registration......................................................................5

Controls and Functions..............................................................6

Set-Up.............................................................................9

System Menu............................................................................12

Operating Modes.......................................................................16

Fuse and Lamp Replacement...................................................18

DMX Traits.................................................................................20

Gobos..................................................................................21

Cleaning..................................................................22

Trouble Shooting.......................................................................22

Warranty....................................................................................23

Specifications....................................................................24

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

During operation the housing may become extremely hot. Avoid touch-

ing the unit with bare hands while in use.

American DJ® will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modiﬁcation to this unit.

DJ Spot 250™ General Instructions

Unpacking: Thank you for purchasing the DJ Spot 250™ by Ameri-

can DJ®. Every DJ Spot 250™ has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your ﬁxture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support ﬁrst.

Introduction: The DJ Spot 250™ is a six channel, moving head, intel-

ligent DMX fixture. The fixture can operate in three different operating

modes; stand alone, sound-active, or in a Master/Slave configuration.

The DJ Spot 250™ comes with several built in programs and is best

used in multiples of four. For best results use fog or special effects

smoke to enhance the beams projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the lamp.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

DJ Spot 250™ General Information

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 22 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

DJ Spot 250™ Safety Precautions

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 4©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 3

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 5

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible (Uses Six DMX Channels)

• Independent Gobo and Color Wheels

• 10 Gobos + Spot - All Replaceable

• 7 Colors, Plus White - With Rainbow

• Color Correction Filter for a Crisp White Color

• Strobing in All Colors and Gobo Shake

• 3 Operating Modes - Master/Slave; Stand Alone, Sound Active;

Universal DMX-512

• Internal Microphone

• ZB-EHJ 24v/250w

• Manual Focus Lens

• 540˚ Pan Movement

• 265˚ Tilt Movement

• Digital Display for Address and Function Setting

• High Velocity Fans for continuous use (no duty cycle)

DJ Spot 250™ Features

The DJ Spot 250™ carries a one year limited warranty. Please fill out

the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper

at the shippers cost.

DJ Spot 250™ Product Registration

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 6

8888

ESC DOWN UP ENTER

DJ Spot 250™ Controls and Functions

REAR

FRONT

3 4 5 6 7

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 8©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 7

DJ Spot 250™ Controls and Functions

1. Lens Assembly - This high quality lens is a fully focusing. Focus

the lens by manually turning the lens in a clockwise or counter-clock-

wise direction until the desired effect is achieved.

2. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

3. ESC (Escape) Button - This button is used to exit menus.

4. Down Button - This button is used to scroll backwards through

certain menus only.

5. Up Button - This button is used to scroll forward when navigating

through the system menu.

6. Enter Button - This button is used to select and conﬁrm a func-

tion when working in the system menu. It is also used to exit certain

menus.

7. Carrying Handles - The includes built-in carrying handles. Be sure

to always handle the unit by the built-in handles. Never lift or carry-

ing the unit by head or yoke. Pulling on or transporting the unit by the

moving head may severely damage the unit and will void the unit war-

ranty.

8. Cooling Fan - This unit is equipped with three high velocity variable

fans to aid in the cooling process. These fans are designed to vary

their velocity at different operating temperatures, to provide better

cooling when the unit reached higher operating temperatures associ-

ated with long usage. Be sure to never obstruct the cooling fans during

normal usage. Also, be sure to keep the vents clean at all times. A

blocked or malfunctioning cooling system may shorten lamp life and

unit reliability.

9. Lamp Assembly and Access Plate - This plate accesses the

lamp socket assembly. The unit includes a spring mounted LL-EHJ

24v/250w halogen lamp. Be sure to only replace with same type lamp.

After replacing a lamp be sure the lamp is centered in the reﬂector. See

page 18 for details on installing and optimizing replacement lamps.

Never operate this unit with the lamp exposed, this lamp emits strong

UV radiation.

10. Audio Sensitivity Knob - This will adjust the audio sensitivity of the

DJ Spot 250™ Controls and Functions

INTERNAL MICROPHONE. Turning the sensitivity knob in the clock-

wise direction will increase the sensitivity to sound. Turning the knob

in the counter clockwise direction will decrease the ﬁxture’s sensitivity

to sound.

11. Tron/C Controller Jack - This jack is for use with the optional

Tron/C controller only. Do not attempt to connect an audio signal this

jack, this will damage the PC board and void your manufactures war-

ranty!

12. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX ﬁxture, or transmit a Master/Slave signal

to the next DJ Spot 250™ in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Terminator” on page 10.

13. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

14. Fuse Holder - This housing stores a 10 amp (5 amp 220v) GMA

protective fuse. Never defeat the fuse, the fuse is designed to pro-

tect the electronics in the event of severe power ﬂuctuations. Always

be sure to replace the fuse with an exact match as the one being

replaced, unless otherwise told to do so by an authorized American

DJ® service technician.

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 9 ©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 10

Power Supply: Before plugging your unit in, be sure the source

voltage in your area matches the required voltage for your American

DJ® DJ Spot 250.™ The American DJ® DJ Spot 250™ is available in

a 120v only. Because line voltage may vary from venue to venue, you

should be sure your unit voltage matches the wall outlet voltage before

attempting to operate you ﬁxture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all ﬁxtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The DJ Spot 250™ can be controlled via DMX-512 proto-

col. The DJ Spot 250™ is a six channel DMX unit.

The DMX address is set electronically using the

controls on the side panel of the unit. Your unit and

your DMX controller require a standard 3-pin XLR

connector for data input and data output (Figure

1). If you are making your own cables, be sure to

use standard two conductor shielded cable (This

cable may be purchased at almost all professional

DJ Spot 250™ Set Up

Figure 1

sound and lighting stores). Your cables should be made with a male

and female XLR connector on either end of the cable. Also remember

that DMX cable must be daisy chained and cannot be split.

DJ Spot 250™ Set Up

Notice: Be sure to follow ﬁgures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 11

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR ﬁxtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

DJ Spot 250™ Set Up

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 12

DJ Spot 250™ System Menu

On-Board System Menu.

The DJ Spot 250™ comes with an easy

to navigate system menu. This next section will detail the functions of

each command in the system menu. You can leave any menu setting

without making any changes by pressing the ESC (ESCAPE) button.

MAIN MENU -

A.001 - DMX Address Setting

1. Press the ESCAPE button until “A.001” is displayed. Press the

ENTER button to adjust the DMX address.

2. Tap the UP or DOWN button until the address that you want

is displayed, press the ENTER button.

TEST - This function will activate one of 3 internal test pro-

grams.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “TEST” is displayed. Press the

ENTER button to choose a test mode.

2. “NOD 1” will now be displayed. Tap the UP button and the dis-

play will go through the modes. Press the ENTER button to

select a mode. Once you select a mode the unit will start the

program. You can now set the speed and fade time of the

program.

3. Tap the UP button and the display will read “SPEE” (Speed).

Press the ENTER button to adjust the speed of the pan and

tilt. You can now adjust the speed between 0 - 255, 0 being

the slowest and 255 being the fastest.

4. Once you have chosen your desired speed press ENTER to

select that speed.

5. Tap the UP button and the display will read “CroS”. This is

the fade time. Press the ENTER button to adjust the fade

time. You can adjust the fade time between 0 - 255, 0 being

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 14©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 13

the slowest and 255 being the fastest.

Note: The fade time should usually be set to a faster speed

then the speed time.

AUDI - This function is the Sound Active mode.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “AUDI” is displayed. Press the

ENTER button.

2. Press the UP button to display “YES”. Press ENTER to con-

ﬁrm.

3. You can adjust the audio sensitivity of the unit by turning the

audio sensitivity knob clockwise, located in the rear.

Note: When the unit is in Sound Active mode, “test run” will

continuously ﬂash on the LCD screen.

RPAN - The movement of the Pan will be reversed.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “R.PAN” is displayed.

2. Press the UP button to choose “ON” or “OFF”, then press

ENTER to conﬁrm.

3. Press ESC to return to the main menu..

R.TILT - The movement of the Tilt will be reversed.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “R.TILT” is displayed.

2. Press the UP button to choose “ON” or “OFF”, then press

ENTER to conﬁrm.

3. Press ESC to return to the main menu.

DISP - This function will reverse the display 180º.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

DJ Spot 250™ System Menu DJ Spot 250™ System Menu

Then press the UP button until “DISP” is displayed. Press the

ENTER button. “TURN” will now be displayed.

2. Tap the UP button to change the display and press ENTER to

conﬁrm the new display.

3. Press ESC to return to the main menu.

VERS - Use this function to display the Software version of

the unit.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “VERS” is displayed. Press the

ENTER button.

2. Tap the UP button until “SET” is displayed, press ENTER.

3. Tap the UP button until “VER” is displayed, press ENTER.

4. The display will show “V-X.X”, “X.X” stands for the version

number, such as the display may show “V-1.0”, “V-2.6” etc.

5. Press ENTER or EXIT/DN to exit.

DEFA - With this function you can restore the factory set-

tings of the device.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “DEFA” is displayed. Press the

ENTER button.

2. The display will show “YES”.

3. Press ENTER to conﬁrm.

7. Press EXIT/DN to return to the main menu.

When you exit this function, the unit will begin to reload

data.

R.S.E.T. - When you activate the reset function, the ﬁxture

will begin the reset motion.

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 16©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 15

DJ Spot 250™ System Menu

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “R.S.E.T.” is displayed. Press

the ENTER button.

2. Tap the UP button until “SET” is displayed, press ENTER.

2. Tap the UP button until “R.S.E.T.” is displayed, press ENTER.

3. The display will show “ON/OFF”.

4. Press the UP button to select “ON” to activate this function,

or “OFF” to deactivate this function.

5. Press ENTER to conﬁrm.

6. Press EXIT/DN to return to the main menu.

Operating Modes: The DJ Spot 250™ can operate in three dif-

ferent modes. This next section will detail the differences in the

operating modes.

• Stand alone mode -

The unit will react to sound, chasing through the built-in programs.

• Master/Slave mode -

You can daisy chain up to 16 units together to get a synchronized

light show without the need of an external controller. The units will

react to sound chasing through the several built-in programs.

• DMX control mode -

This function will allow you to control each individual fixtures

traits with a standard DMX-512 controller such as the LSC® Show

Designer.™

Universal DMX Control: This function allows you to use a univer-

sal DMX-512 controller such as the LSC® DMX Operator™ or LSC®

Show Designer™ to control head movement, the color wheel, gobo

wheel, and the shutter (strobe). A DMX controller allows you to create

unique programs tailored to your individual needs.

1. The DJ Spot 250™ uses six DMX channels. Channel 1 con-

trols pan, channel 2 controls tilt, channel 3 controls color, channel

4 controls gobo wheel, channel 5 controls the special functions,

and channel 6 controls the speed of the Pan and Tilt movement.

See page 22 for a detailed description of the DMX traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 10-14 as well as the set-up specifications that are

included with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 16 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

DJ Spot 250™ Operation

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 18©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 17

DJ Spot 250™ Operation

Stand-Alone Operation (Sound Active): This mode allows a single

unit or several units linked together, to run to the beat of the music.

1. Press the ESCAPE (ESC) button until “A.001” is displayed.

Then press the UP button until “AUDI” is displayed. Press the

ENTER button.

2. Press the UP button to display “YES”. Press ENTER to con-

ﬁrm.

3. You can adjust the audio sensitivity of the unit by turning the

audio sensitivity knob clockwise, located in the rear. You may

invert the pan and tilt functions by in the system menu by follow-

ing the directions on page 13.

Note: When the unit is in Sound Active mode, “test run” will

ﬂash on the LCD screen.

Master-Slave Operation (Sound Active): This function will allow

you to link up to 16 units together and operate without a controller. The

units will be sound activated. In Master-Slave operation one unit will

act as the controlling unit and the others will react to the controlling

units programs. Any unit can act as a Master or as a Slave.

1. Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remem-

ber the Male XLR connector is the input and the Female XLR

connector is the output. The ﬁrst unit in the chain (master) will use

the female XLR connector only - The last unit in the chain will use

the male XLR connector only. For longer cable runs we suggest a

terminator at the last fixture.

2. Set all Slave units to the same DMX address as the Master.

DJ Spot 250™ Fuse & Lamp Replacement

This fixture is fitted with a halogen lamp which is

highly susceptible to damage if improperly han-

dled. Never touch the lamp with your bare fingers

as the oil from your hands will shorten lamp life.

Also, never move the fixture until the lamps have

had ample time to cool. Remember, lamps are

not covered under warranty conditions.

A B

Caution: Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American DJ® service

technician. Replacing with anything other than the specified part can

damage your unit and will void your manufactures warranty.

Warning: If you continue to blow lamps or fuses, STOP using the

unit. Contact customer support for further instructions, you may have

to return the unit for servicing. Continuing to use the unit may cause

serious damage.

Lamp Replacement: Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a slide out socket assembly that is retained by thumb screws.

1. Be sure to follow the proper handling procedures that deal with

discharge lamps.

2. Remove the two small screws (A,B) on the rear of the unit

3. After removing the screws, gently slide out the socket assembly

from the rear of the unit to expose the lamp.

4. Carefully remove the old lamp and discard it in the trash.

5. Replace the lamp with an exact match and reassemble in reverse

order.

6. After replacing the lamp follow the optimization procedures on the

next page to be sure the lamp is center in the reflector

©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 20©American DJ® - www.americandj.com - DJ Spot 250™ Instruction Manual Page 19

DJ Spot 250™ DMX Traits

Channel Value Function

1 0 - 255 PAN

2 0 - 255 TILT

3 0 - 199 COLOR

0 - 24 WHITE

25 - 49 RED

50 - 74 YELLOW

75 - 99 BLUE

100 - 124 GREEN

125 - 149 PURPLE

150 - 174 ORANGE

175 - 199 PINK

200 - 255 RAINBOW EFFECT

4 GOBO

0 - 16 NONE

17 - 33 SPOT

34 - 50 GOBO 1

51 - 67 GOBO 2

68 - 84 GOBO 3

85 - 101 GOBO 4

102 - 118 GOBO 5

119 - 135 GOBO 6

136 - 152 GOBO 7

153 - 169 GOBO 8

170 - 186 GOBO 9

187 - 199 GOBO 10

200 - 255 RAINBOW EFFECT

Optimizing Lamp Alignment: This procedure centers the lamp in the

reflector. Proper optimization will increase lamp life and ensure a bright

crisp output. Improper optimization may add a yellow tint to the lamp

output and reduce intensity.

1. Be sure main power is disconnected and allow the unit to cool. If

the you have just installed a new unit you can obviously skip this

step.

2. Make a preliminary adjustment: Turn the three lamp adjustment

thumb screws completely in (clockwise). Then back them each

out (counter-clockwise) about three complete turns.

3. Turn the unit on and allow it to reset.

4. Using either a DMX controller or the control panel on the unit,

strike the lamp and focus the light on a ﬂat surface.

6. Center the hot-spot (the brightest part of the beam) using the 3

adjustment screws. Turn one screw at a time to drag the hot-spot

diagonally across the projected image. If you cannot detect a hot-

spot, adjust the lamp until the light is even.

7. To reduce a hot-spot, pull the lamp in by turning all three screws

clockwise 1/4-turn at a time until the light is evenly distributed.

8. If the light is brighter around the edge than it is in the center, or if

light output is low, the lamp is too far back in the reﬂector. “Push”

the lamp out by turning the screws.

DJ Spot 250™ Fuse & Lamp Replacement

Optimizing Screws Optimizing Screws

Fuse Replacement: Locate and remove the unit’s power cord. Once

the cord has been removed located the fuse holder located inside the

power socket. Insert a flat-head screw driver into the power socket

and gently pry out the fuse holder. Remove the bad fuse and replace

with a new one. The fuse holder has a built-in socket for a spare fuse

be sure not to confuse the spare fuse with active fuse.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Double Feature Bedienungsanleitung

American DJ

American DJ Flight-Moon Bedienungsanleitung

American DJ

American DJ Mega Bar PRO Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ M-103HD Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ Stingray Bedienungsanleitung

American DJ

American DJ Sunray Tri LED DMX Bedienungsanleitung

American DJ

American DJ LED Vision Bedienungsanleitung

American DJ

American DJ User Instructions Bedienungsanleitung

American DJ

American DJ WLED CURTAIN Bedienungsanleitung

American DJ

American DJ 64WH LED PRO Bedienungsanleitung

American DJ

American DJ Color Fusion Bedienungsanleitung

American DJ

American DJ Dual Gem Pulse Bedienungsanleitung

American DJ

American DJ Atmospheric RG LED Bedienungsanleitung

American DJ

American DJ Vizi Scan LED PRO Bedienungsanleitung

American DJ

American DJ Sapphire 4 Bedienungsanleitung

American DJ

American DJ RollerTron Bedienungsanleitung

American DJ

American DJ LED Beam Scan Bedienungsanleitung

American DJ

American DJ Super Jewel Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

American DJ

American DJ Mighty Scan Bedienungsanleitung

American DJ

American DJ Hypnotic RGB Bedienungsanleitung

American DJ

American DJ S-10S Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung