American DJ Vizi Scan LED PRO Bedienungsanleitung

Rev. 4/14

User Instructions

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 2

American DJ®

Vizi Scan LED PRO

Table of Contents

General Information.....................................................................4

Features.........................................................................4

Safety Precautions......................................................................5

Registration......................................................................6

Handling Precautions..................................................................6

Mounting.................................................................................7

Controls and Functions..............................................................9

DMX Set-Up..............................................................................12

System Menu............................................................................15

Editing Program.........................................................................33

Operating Modes.......................................................................38

DMX Traits.................................................................................40

Fuse Replacement....................................................................47

Gobo Replacement...................................................................48

Photometric Chart.....................................................................49

Cleaning..................................................................50

Trouble Shooting.......................................................................50

Warranty.................................................................51

Specifications....................................................................52

Unpacking: Thank you for purchasing the Vizi Scan LED PRO by

American DJ®. Every Vizi Scan LED PRO has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The Vizi Scan LED PRO is a bright, high output, intel-

ligent DMX scanner. The Vizi Scan LED PRO can be either a 12 or 14

DMX Channel unit. The fixture can operate in three different operating

modes; sound active, auto run, or DMX control. The fixture can run

as as a Stand Alone unit or in a Master/Slave configuration. The Vizi

Scan LED PRO comes with several builtin programs and is best used

in multiples of four. For best results use fog or special effects smoke to

enhance the beams projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the unit.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Vizi Scan LED PRO General Information

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 4American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 3

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• 2 DMX Channel Modes - 12 Channel Mode & 14 Channel Mode

• Independent Gobo and Color Wheels

• 7 Rotating Gobos w/ Shake, 5 Metal and 2 Glass + Spot - All

Replaceable

• 8 Colors, Plus White - With Rainbow

• Prism Wheel: 3 Facet; Trapezoid; Frost

• RDMX - Lets you set the DMX address from any DMX Controller

• 3 Operating Modes - Sound Active, Auto Run, & DMX Control

• Internal Microphone

• Edit and Save Scenes into the Memory

• Remote Focus

• Variable Strobe (1-12 fps)

• Motor Calibration Adjustment

• Pan: 540 or 630 Degrees

• Tilt: 35 Degrees

• Mic Sensitivity Adjustment

• Digital Display for Address and Function Setting

Vizi Scan LED PRO Features

Vizi Scan LED PRO RDMX

Regarding RDMX :

1. The units will be shipped preset in 16 channel increments

from the factory

2. While using RDMX, if all units are set to the same DMX

address, all units will change to the new DMX address you

selected.

EXAMPLE: You have four units, and all the units are set to the

DMX address of “1”, and you change one unit to DMX address

“17”, this will cause all the units to change to DMX address

“17”.

All four units must be on 4 dierent starting addresses to indi-

vidually set the DMX addresses for each unit.

For more on this feature see pages 25-26.

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 5 American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 6

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 50 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Vizi Scan LED PRO Safety Precautions

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Vizi Scan LED PRO General Instructions

The Vizi Scan LED PRO carries a 2year (730 Day) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

The R.A. number must be clearly written on the outside of the return

package. A brief description of the problem as well as the R.A. num-

ber must also be written down on a piece of paper and included in the

shipping carton. If the unit is under warranty, you must provide a copy

of your proof of purchase invoice. You may obtain a R.A. number by

contacting our customer support team on our toll free customer sup-

port number. All packages returned to the service department not dis-

playing a R.A. number on the outside of the package will be returned

to the shipper at the shippers cost.

Vizi Scan LED PRO Product Registration

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

During operation the housing may become extremely hot. Avoid touch-

ing the unit with bare hands while in use.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Vizi Scan LED PRO Handling Precautions

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 8American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 7

Vizi Scan LED PRO Mounting

The Vizi Scan LED PRO is fully operational in three dierent mount-

ing positions, hanging upside-down from a ceiling, side mounted, or

set on a at level surface. To avoid internal damage to the unit, never

mount the unit on its side as illustrated above. Be sure this xture is

kept at least 0.5m away from any ammable materials (decoration

etc.). Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the

clamp fails (see next page). Never use the carrying handles for sec-

ondary attachment.

When installing the unit, the trussing or area of installation must be

able to hold 10 times the weight without any deformation. When

installing the unit must be secured with a secondary safety attach-

ment, e.g. and appropriate safety cable. Never stand directly below

the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat-

ing working load limits, installation material being used, and perodic

safety inspection of all installation material and unit. If you lack these

qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

Vizi Scan LED PRO Mounting

Screw one clamp each via a M12 screw and nut directly into

the bracket of the scanner. Pull the safety-cable through the

bracket of the base and over the trussing system or safe xa-

tion spot.

NOTICE: The suitable enviromental temperature for this light-

ing xture is between -25˚ C to 45˚ C. Do not place this lighting

xture in an enviroment where the temperatures are under or

above the temperatures stated above. This will allow the xture

to run at its best and help prolong the xture life.

Vizi Scan LED PRO Controls and Functions

1. Mirror - This is a highly reective surface mirror specically designed

to optimize and enhance beam output. Never use glass cleaners that

contain ammonia to clean the surface of the mirror (such as Windex).

2. Lens Assembly - This high quality lens is a fully focusing. Focus

the lens by manually turning the lens in a clockwise or counter-clock-

wise direction until the desired eect is achieved.

3. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

4. Mode/Esc Button - This button is used to enter the main menu and

submenus. It is also used to exit menus.

5. Up Button - This button is used to scroll forward when navigating

through the system menu.

6. Down Button - This button is used to scroll backwards when navi-

gating through the system menu.

7. Enter Button - This button is used to select and conrm a function

in the system menu.

8. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active mode. This microphone is designed

to receive low frequency sounds only, tapping on the microphone and

high pitch sounds may not trigger the unit.

9. Control Board

10. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

11. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX xture, or transmit a Master/Slave signal

to the next Vizi Scan LED PRO in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Terminator” on page 13.

12. Power Cord - This cord used to supply power to the unit. Never

use this unit if the cord is broken or frayed. Never use this xture if the

ground prong has been removed or broken o. The ground prong is

designed to reduce the risk of re or electrical shock in the event the

unit suers from an internal short.

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 9 American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 10

Vizi Scan LED PRO Controls and Functions

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 11 American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 12

Power Supply: The American DJ®Vizi Scan LED PRO contains a

automatic voltage switch, which will auto sense the voltage when it is

plugged into the power source. With this switch you do not need to

worry about wall voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Vizi Scan LED PRO can be controlled via DMX-512

protocol. The Vizi Scan LED PRO can be either a 12 or 14 DMX Chan-

nel unit. The DMX address is set electronically using the controls on

the front panel of the unit. Your unit and your DMX

controller require a approved DMX-512 110 Ohm

Data cable for data input and data output. We

recommend Accu-Cable DMX cables. If you are

making your own cables, be sure to use standard

110-120 Ohm shielded cable (This cable may be

purchased at almost all professional sound and

lighting stores). Your cables should be made with

a male and female XLR connector on either end of

Vizi Scan LED PRO Set Up

Figure 1

Vizi Scan LED PRO Controls and Functions

13. Power Switch - This switches the power to the xture “On” &

“O”.

14. Fuse Holder - This housing stores a 4 amp protective fuse. Never

defeat the fuse, the fuse is designed to protect the electronics in the

event of severe power uctuations. Always be sure to replace the fuse

with an exact match as the one being replaced, unless otherwise told

to do so by an authorized American DJ®service technician.

the cable. Also remember that DMX cable must be daisy chained and

cannot be split.

Vizi Scan LED PRO Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Vizi Scan LED PRO Set Up

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 14American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 13

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 16American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 15

ADDRESS MENU -

AOO1 - A511 (Value) - This is where you set the DMX address of

the unit.

TEST MENU -

T-01 - T-XX (Test) - Tests the functions of each channel. Note:

Some channels cannot be tested.

PLAY MENU -

RUN - Runs the unit as a “master” or in a stand alone mode. The

unit will run a internal program mode.

AUDI (Audio) - Runs the unit as a “master” or in a stand alone,

sound active mode.

AUTO - This is a precaution mode in case the DMX signal is lost.

There are four settings to choose from:

• “Hold” - This is the default setting, which in case the signal is

lost the xute will “hold” at the last setting.

• “Close” - The xture will return to its “home” standing.

• “Auto” - The xture will go into Auto mode and run a pre-pro-

grammed show.

• “Audi” - The xture will go into Sound Active mode.

RESE (RESET) MENU -

ALL - Resets all the motors in the unit.

SCAN - Resets the motors that control pan/tilt.

COLR (Color) - Resets the color motors.

GOBO - Resets the gobo motors.

OTHR - Resets all other motors.

TIME MENU -

LIFE - Displays the xtures total running time.

Vizi Scan LED PRO System Menu

Default setting shaded.

1 ADDR AXXX A001 Indicate the staring DMX address

A001 also is the setting for slave

2 TEST T-01~T-XX Automatically test the function

RUN MSTR/ALON Runs fixture as “master” or “alone” for

auto

AUDI MSTR/ALON Runs fixture as “master” or “alone” for

audio

3 PLAY

AUTO Clos/Hold/Auto/Audi No DMX Status

ALL Reset all motors and returns fixture to

home

SCAN Reset only motors for pan/tilt

COLR Reset only motors for colors

GOBO Reset only motors for gobo and rotation

4 RESE

OTHR Reset other motors

LIFE 0000~9999 Displays the total fixture running time

5 TIME CLMP Clear lamp running time

6 RPAN ON/OFF Reverses the pan movements

7 RTLT ON/OFF Reverses the tilt movements

8 FINE ON/OFF Switch 16 bit/8 bit

9 MIC M-XX M-70 Mic sensitivity

VALU D–XX D-00 (DXXX) Display the DMX512 value of each

channel

D ON ON/OFF Display turn off after 2mins

FLIP ON/OFF This function will reverse the display

180

10 DISP

LOCK ON/OFF Key lock

RDMX ON/OFF Change DMX address via external

controller

SPOT ON/OFF Lamp optimization

DFSE ON/OFF Resets all the fixture functions to

default

FANS AUTO/HIGH/LOW Fan’s mode select

HIbE OFF/1-99M 15M Stand by mode

VER V1.0~V9.9 Software version

CODE CXXX Fixture code *code is “C050”

11 SPEC

ADJU CH01~CHXX XXXX(-128~127) Motor Fix

SEPR AUTO

IP01~IP07 Select program to be edit

STEP S–01 ~S–48 Set the amount of your

program

C–01~C–XX XXX(0~255) Edit the channels of each

scene

TIME T XXX(001~999) Time for each scene

SCXX

CEDT ON/OFF Edit program via controller

REC. RE.XX Auto Save

12 EDIT

RUN ON/OFF Program test

Vizi Scan LED PRO System Menu

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 18American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 17

Vizi Scan LED PRO System Menu

CLMP - Clears the xture running time.

RPAN (REVERSE PAN) MENU -

ON/OFF - When “On” is chosen it will reverse the pan.

RTILT (REVERSE TILT) MENU -

ON/OFF - When “On” is chosen it will reverse the tilt.

FINE MENU -

ON/OFF - Switch between 8bit (coarse) and 16bit (ne) pan & tilt

movement. This also switches the DMX channel mode between

12 channel (8 bit) and 14 channel (16 bit) DMX mode.

MIC MENU -

M-01-M-70 - With this function you can make the internal mic

more or less sensitive to sound.

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON (Display On) - Turns digital display on and o.

FLIP - “Flips” the digital display 180º.

LOCK - When activated the buttons will lock automatically. See

page 26 for more information.

SPEC MENU -

RDMX - On/O With this function you are able to change the

DMX address via external controller. See pages 25-26.

SPOT - This provides a spot beam for better lamp optimization.

DFSE - This will reset the unit to the default settings.

FANS - Select the fan running mode.

HIBE - This feature will automatically shut down the lamp and

stepping motors. Please see pages 28-29.

VER (Version) - Software version 2.2

Vizi Scan LED PRO System Menu

ADJU - Calibration functions

EDIT MENU -

SEPR (AUTO IP01 - IP07) - Lets you edit any of the 7 internal

programs.

STEP (Step) - Steps to be used in Edit Programming. See ediit

program. See pages 33-35.

SCO1 - SC48 (Scene 01 - Scene 48) - These are the scene slots

that you write your programs into. See edit program, pages

33-35.

TIME (Time) - Time for each scene. See pages 33-35.

CEDT - Edit program using a external controller. See pages

33-35.

C-01 - C-30 (Channel 1 - Channel 30) - The channels of each

scene that can be edited. See pages 33-35.

American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 20American DJ®- www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 19

Vizi Scan LED PRO System Menu

number 1, if you press the UP button until “T0-3” is displayed,

the unit will test the color channel, changing the color one by

one and showing the rainbow eect with dierent speeds.

4. Press MODE/ESC to exit.

PLAY MENU -

RUN Run the unit in an Auto mode as a “master” in a

Master/Slave conguration, or as a stand alone unit -

1. Access the main menu.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “RUN” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice by pressing ENTER, “PASS” will ash

in the display and xture will begin its function.

AUDI Run the unit in Sound Active mode as a “master”, or

as a stand alone unit -

1. Access the main menu.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “AUDI” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice by pressing ENTER, “PASS” will ash

in the display and xture will begin its function.

AUTO This is a precaution mode in case you lose the DMX

signal. The xtue has 4 modes to choose from, please see

page 16 for a description of the 4 modes -

1. Access the main menu by pressing MODE/ESC button.

Vizi Scan LED PRO System Menu

On-Board System Menu.

The Vizi Scan LED PRO comes with an

easy to navigate system menu. This next section will detail the func-

tions of each command in the system menu.

ADDR MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu.

2. Tap the UP button until “ADDR” is displayed, press ENTER.

3. “A001” will now be displayed. Press the UP or DOWN buttons

to nd your desired address. Press ENTER to conrm.

4. The display will show “PASS”, and then display, your selected

address again.

5. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DN buttons to change the DMX start address.

TEST MENU -

TEST - This will test the functions of each channel.

1. Access the main menu.

2. Tap the UP button until “TEST” is displayed, press ENTER.

3. The display will show “T0-1”, “1” stands for the channel

To access the main menu locate the ENTER button (7) on the front

of the unit. Press this button to activate the system menu. Tap the

UP button (5) or DOWN button (6) until you reach function you wish

to change. When you reach the function you wish to change tap the

ENTER button. When a function is selected the menu will begin to

ash, use the UP button to change the function. Once your changes

are made tap the ENTER button again to lock the change in the system,

if the ENTER button is not selected within eight seconds the system

will automatically return to menu section. To exit without making any

changes tap the MODE/ESC button (4).

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ X-CALIBUR Bedienungsanleitung

American DJ

American DJ UVLED Bar16 Bedienungsanleitung

American DJ

American DJ Accu Spot 575 Bedienungsanleitung

American DJ

American DJ Dynasty Scan DMX Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ 4-Play Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ LED Messenger Bedienungsanleitung

American DJ

American DJ Deco 250 Bedienungsanleitung

American DJ

American DJ Mega Pixel LED Bedienungsanleitung

American DJ

American DJ Flat Par Tri7X Bedienungsanleitung

American DJ

American DJ LunarPod Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Bedienungsanleitung

American DJ

American DJ H2O 250 EX Bedienungsanleitung

American DJ

American DJ Duo Scan RG Bedienungsanleitung

American DJ

American DJ Double Feature Bedienungsanleitung

American DJ

American DJ Light Station Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ PDP-800 Bedienungsanleitung

American DJ

American DJ LED Vision Bedienungsanleitung

American DJ

American DJ Revo XPress Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ Fusion Tri FX Bar Bedienungsanleitung

American DJ

American DJ Octo Beam Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung