American DJ DP-DMX-20L Bedienungsanleitung

American DJ

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

User Instructions

American DJ®

Introduction:

Thank you for purchasing the DP-DMX-20L

™ 4 channel dimmer pack

from American DJ. To optimize the performance of this product, please

read these operating instructions carefully and familiarize yourself with

the basic operations of this unit. The American DJ® DP-DMX-20L,

™ is a

four channel, DMX dimmer pack. This unit has been tested at the factory

before being shipped to you. There is no assembly required.

The American DJ® DP-DMX-20L™ is controlled via a standard DMX

controller such as the American DJ Show Designer,

™ or the American

DJ® DMX Operator.

™ This unit allow you to control special effect light-

ing, that normally could not be controlled, by a DMX controller. With this

revision to our popular DP-DMX20™ we have eliminated confusing dip

switches and replace them with an easy to use digital switching device

that incorporates the use of an easy to read LCD display.

Customer Support:

American DJ® provides a toll free customer support line to provide set

up help and answers to any question should you encounter problems

during your set up or initial operation. You may also visit us on the web

at www.americandj.com for any comments or suggestions.

Service Hours are Monday through Friday 10:00 a.m. to 5:00 p.m.

Pacic Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: suppor[email protected]

Warning!

To prevent or reduce the risk of electrical shock or re, do not expose

this unit to rain or moisture. Clearing memory often may cause damage

to the memory chip, be careful not to re initialize your unit frequency

often to avoid this risk. Only use the recommended AC/DC power adap-

tor.

Caution!

There are no user serviceable parts inside this unit. Do not attempt any

repairs yourself, doing so will void your manufactures warranty. In the

unlikely event your unit may require service, please contact your near-

est American DJ® dealer.

©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 2

DP-DMX-20L

4 CHANNEL DMX

DIMMER PACK

Set Up:

Power Supply: Before plugging your unit in be sure the source

voltage in your area matches the required voltage for your American

DJ® DP-DMX-20L.™ The DP-DMX-20L™ is available in a 115v and

230v version. Because line voltage may vary from venue to venue, you

should be sure to plug your power supply into a matching wall outlet

before attempting to operate you controller.

Data Cable (DMX Cable) Requirements:

Your power pack and your controller

require a standard 3-pin XLR connector

for data input and data output (Figure

1). If you are making your own cables

be sure to use standard two conductor

shielded cable (This cable may be pur-

chased at almost all pro sound and light-

ing stores). Your cables should be made

with a male and female XLR connector

on either end of the cable. Also, remem-

ber that DMX cable must be daisy

chained and can not be “Y”ed or split.

Notice: Do not use the ground lug on the XLR connector. Do

not connect the cable’s shield conductor to the ground lug or allow

the shield conductor to come in contact with the XLR’s outer casing.

Grounding the shield could cause a short circuit and erratic behavior.

Figure 1

Figure 2

DMX +

DMX -

COMMON

DMX512 IN

(X-CALIBUR)

CONNECTOR

3 PIN

DMX512 OUT

CONTROLLER

CONNECTOR

3 PIN

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 3

Figure 3

DMX +

DMX -

COMMON

DMX512 IN

(X-CALIBUR)

CONNECTOR

3 PIN

DMX512 OUT

CONTROLLER

CONNECTOR

3 PIN

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 90 - 120 ohm

1/4 watt resistor which is connected between pins 2 and 3 of a male

XLR connector (DATA + and DATA -). This unit is inserted in the female

XLR connector of the last unit in your daisy chain to terminate the line.

Using a cable terminator will decrease the possibilities of erratic behav-

ior.

Product Description:

The DP-DMX20L,™ is 1, 2, or 4 channel DMX Dimmer Pack. This

pack can serve as a stand alone chaser or a DMX dimmer pack.

This pack is designed for zero-crossing circuitry which protects

aginst inductive loads, so it is safe for use with all lighting effects

that include transformers such as pin spots. Each channel comes

with two 3-prong Edison sockets inputs for a total of eight. This

unit features XLR female and male connection for DMX compat-

ability. Each channel is equiped with a fuse for each channel,

and a maximum output load of 10A per channel or 20A total.

This revision of our popular DP-DMX20™ has a great new case

design that makes it great for permanent or mobile applications.

©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 4

Figure 4

XLR MALE SOCKET

1 EARTH 2 COLD

3 HOT

XLR FEMALE SOCKET

1 EARTH

COLD 2

3 HOT

XLR Pin Configuration:

Pin 1 = Shield

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Functions and Controls Front Panel: Functions and Controls Rear Panel:

8. Channel Fuses - Each of the four channels is protected by a 6.3A

fuse. These fuses prevent you from overloading and damaging

your pack. Be sure to always replace with the exact same type fuse.

9. Power Switch - This switxh controls the units main power.

10. Power Cord - Plug this cord into a matching power

supply for your area.

11. DMX Input - This connector accepts your DMX input signal.

12. DMX Output - This connector sends your DMX input

signal through to the next DMX device.

1. Mode Button - This button will change the paower packs

operate mode between DMX and chaser.

2. Menu Button - This button will activate the different

functions in DMX and chase modes.

3. Up Button - This button will increse the displayed value in the LCD

display.

4. Down Button - This button will decrease the displayed

value in the LCD display.

5. POWER OUTPUT - 3-prong grounded Edison output

sockets. 8 total output sockets.

6. GREEN L.E.D. Indicators - These LEDs will idicate their

relevant channel activity.

7. LCD Display - This multifunction display will detail all chase and

progrativity that pertains to the current operating mode of the pack.

Operation Modes:

The DP-DMX-20L

™ has two different operating modes. This unit can be

used as a four channel chaser or as a 1, 2, or 4 channel DMX dimmer

pack. Please follow the instructions below to operate the unit in your

desired mode.

Chase Mode:

Use this operating mode only if you are planning on using your DP-

DMX-20L

™ as a four channel chaser. This device has 16 built in pro-

grams, you may select any of these programs or set the pack to chase in

a random sequence of all 16 built in programs for a more dramatic light

show. You may control the speed at which the programs will chase.

1. Connect your lighting effects to the any of the eight power

sockets on the pack.

2. Use the mode button to select chase mode: Chase mode is

indicated by "PA" followed by numbers 01-16. "PA" is Programmed

Applied. If "A" appears in the LCD display you are in DMX mode,

©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 6©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 5

Figure 5

American DJ ®

1 2 3 4

OUTPUT: 5A/CH, TOTAL 15A Max.

OPERATION

DISPLAY ITEMS

MODE:

MENU:

Select RECEIVE or CHASE

Select DISPLAY ITEMS

Increase DISPLAY ITEMS

Decrease DISPLAY ITEMS

TOTAL DMX CHANNELS

DMX CHANNEL

CHASE PROGRAM

CHASE SPEED

CHASE DIMMER

DMX Signal

MODE

CH1

CH2 CH3 CH4

4 CHANNEL DMX POWER PACK

DMX Signal

2 4 3

8888

CH:01 CH:04

A:001 A:512

P:01 P:16

SP:01 SP:99

D:000 D:100

POWER INPUT: AC 120V~50-60Hz, 15A max.

POWER

1=Ground

2=Data-

3=Data+

WARNING:

TH IS APP ARA TUS MU S T B E E AR T HE D

N’ OUV REZ PA S.. R IS Q UE DE CH O CE L CT R IQU E

FUSES: F6A 250V 5x20 mm

OFF

3 41

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DMX IN DMX OUT

8 1211

9 10

"A" stands for address.

3. Set your desired chase pattern: Once you have selected the chase

function use the MENU button to select your desired chase. The

chase pattern is represented in the LCD display by "P" followed

by two numbers. You may select any of the built in 16 programs

to run at a single time.

4. Set your desired chase speed: At this point you may change the

program chase speed. While in chase mode, tap on the MENU

button until the "SP" followed by two numbers is displayed in the

LCD. Then use the UP and DOWN buttons to adjust the chase

speed. A value of 99 will give you the fastest chase speed (about

1/10th of a second). A value of 01 will give you the slowest chase

speed (one step every 30 sec.).

5. You may now change the light intensity: Use the MENU button to

select "d" in the LCD. Use the UP and DOWN arrow keys to change

the light output intensity. 00 will give give the loweat output and 99

will give you full intensity.

DMX Mode:

Use this operating mode only if you plan to use your pack as a DMX

dimmer. This function will allow you to turn on and control the intensity

of non-DMX with the use of a DMX controller. On, off, and dimming

functions can be performed through this pack. You may also set your

dimmer pack to functions as a 1, 2, or 4 channel DMX dimmer pack,

which means you can combine the output functions.

DMX Operation

1. Plug in a DMX controller to your dimmer pack via the 3-pin XLR

cables.

2. Connect your lighting effects to any of the eight power sockets on

the front of the pack.

3. Decide if you are going to use your dimmer pack as 1, 2, or 4

channels. This function allows you to;

a. Controll the output to all four outlets with one DMX channel.

b. Group outlet channels one and two and group outlets

channels three and four. The rst group will be controlled by

one DMX channel and the second group will be controlled

by another DMX channel. This gives the pack a DMX value

of two.

c. The default setting is a four channel DMX switcher, each

channel is controlled by one DMX channel.

4. To change the channel function mode be sure you are in DMX

mode. Use the Menu button to select "CH" followed by two digits.

Then use the UP and DOWN arrow buttons to change the setting

from 01, 02, or 04. Your dimmer pack is initially set as a four

channel DMX switcher.

5. The dimmer pack is initially set to be activated by DMX address

one. To change this setting be sure you are in DMX mode. Use

the MENU button to select the address settings, this will be

indicated by an "A" in the rst character of the LCD followed by

three numbers. Use the UP and DOWN arrow buttons to select

your desired DMX address. Remember the DMX address tells your

DMX controller what channel to activate the pack's functions.

6. Once you have set the pack's DMX address be sure your

controller's address matches that of the packs'.

7. Your pack will now opearte as DMX dimmer, you may control the

light output intensity through your DMX controller. 0 will give no

output and 100 will give you full output.

Fuse Replacement: To replace the protective fuse, use a at head

screwdriver to unscrew the fuse holder. Pull out the old fuse and

replace it with a new one. Insert the fuse back into slot and tighten.

Always replace with the exact same type fuse remove unless otherwise

specied by an authorized American DJ® service technician.

Caution: Always disconnect the units main power before performing

any type of service or fuse replacement!

For any service related issues,please contact American DJ®.

©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 7 ©American DJ Supply® - www.americandj.com - DP-DMX-20L Instruction Manual Page 8

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Mighty Scan Bedienungsanleitung

American DJ

American DJ Mobile Beam Bedienungsanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ Color Gem Bedienungsanleitung

American DJ

American DJ Tempest II/AS Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Bedienungsanleitung

American DJ

American DJ DJ Spot LED Bedienungsanleitung

American DJ

American DJ LTS-1 Bedienungsanleitung

American DJ

American DJ Mega Flash DMX Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ Verti-Pro Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Bedienungsanleitung

American DJ

American DJ Concept 1 Bedienungsanleitung

American DJ

American DJ X-Color LED Plus Bedienungsanleitung

American DJ

American DJ Fusion Scan 250EX Bedienungsanleitung

American DJ

American DJ VioMoon LED Bedienungsanleitung

American DJ

American DJ BPP-20 Bedienungsanleitung

American DJ

American DJ Scrambler Bedienungsanleitung

American DJ

American DJ Fusion Tri FX Bar Bedienungsanleitung

American DJ

American DJ Jelly Jewel LED Bedienungsanleitung

American DJ

American DJ Confusion Bedienungsanleitung

American DJ

American DJ Saturn Tri LED Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ Rover Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung