American DJ Mega Flash DMX Bedienungsanleitung

American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 2

Unpacking: Thank you for purchasing the Mega Flash DMX™ by

American DJ®. Every Mega Flash DMX™ has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your unit

for damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event damage has been found or parts are

missing, please contact our customer support number for further

instructions. Please do not return this unit to your dealer without first

contacting customer support at the number listed below.

Introduction: To optimize the performance of this product, please

read these operating instructions carefully to familiarize yourself with

the basic operations of this unit. The Mega Flash DMX™ is a 800 watt

strobe, that has a flash rate range of 1 to 15 flashes per second. Up

to 16 units may be linked together and controlled by single controller.

The units’ intensity, and flash rate can be manually adjusted using the

dipswitches.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments

or suggestions. For service related issue please contact American

DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m.

Pacific Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or fire, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty.

Please recycle the shipping carton when ever possible.

Mega Flash DMX™ Introduction

User Instructions

7/04

American DJ®

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

American DJ ®

Mega Flash DMX™ Warranty Registration

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 3

The Mega Flash DMX™ carries a one year (365 days) limited war-

ranty. Please fill out the enclosed warranty card to validate your pur-

chase. All returned service items whether under warranty or not, must

be freight pre-paid and accompany a return authorization (R.A.) num-

ber. The R.A. number must be clearly written on the outside of the

return package. A brief description of the problem as well as the R.A.

number must also be written down on a piece of paper and included

in the shipping container. If the unit is under warranty, you must pro-

vide a copy of your proof of purchase invoice. You may obtain a R.A.

number by contacting customer support at (800) 322-6337.

Mega Flash DMX™ Cleaning Instructions

Due to fog residue, smoke, and dust cleaning the fixture should be

carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing every 20 days.

2. Use normal glass cleaner with a soft cloth to wipe down the inside

reflector and lens every 30-60 days.

3. Always be sure to dry all parts completely before plugging the

unit back in.

4. Frequent cleaning the unit will extend lamp life and ensure the fix-

tures reliability.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we rec-

ommend cleaning on a monthly basis. Periodic cleaning will ensure

longevity, and crisp beam output.

Mega Flash DMX™ Features

• Bright 800 Watt Lamp ZB-800

• Adjustable Flash Rate, and Intenstiy Rate

• Flash Rate range of 1 to 15 Flashes per Second

• Thermostat Protection

• Large coverage area

• Easy lamp Replacement

• Built-In Adjustable Hanging Yoke

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 4

Mega Flash DMX™ Safety Warnings

Safety Issues: This unit may blow a fuse if the maximum allotted load

of 15 amps is reached. If the fuse needs replacement, always replace

the fuse with same exact type that was remove, unless otherwise

instructed by an authorized American DJ® service technician. Use of a

different type fuse from that which is recommended may cause fire or

electric shock and will void the manufactures warranty.

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short. Do not attempt to oper-

ate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 6 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

Mega Flash DMX™ DMX Set Up

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 5

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Mega Flash DMX.™ The American DJ® Mega Flash DMX™ is 120v only.

Because line voltage may vary from venue to venue, you should be

sure your unit voltages matches the wall outlet voltage before attempt-

ing to operate you ﬁxture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a sin-

gle controller, as long as all ﬁxtures and the controller are DMX com-

pliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Dipswitches in DMX mode: This unit uses dipswitches to assign a

DMX address. Each dipswitch represents a binary value.

Dipswitch 1 address equals 1

Dipswitch 2 address equals 2

Dipswitch 3 address equals 4

Dipswitch 4 address equals 8

Dipswitch 5 address equals 16

Dipswitch 6 address equals 32

Dipswitch 7 address equals 64

Dipswitch 8 address equals 128

Dipswitch 9 address equals 256

Dipswitch 10 - Some units omit dipswitch 10. When a unit does

include dipswitch #10, it is usually used for special functions such as

Mega Flash DMX™ DMX Set Up

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 6

sound activation.

Assigning DMX Address: Each dipswitch has a preset value. A spe-

cific DMX address is set by combining the dipswitches that sum your

desired value. For example: To achieve a DMX address of 7, combine

dipswitches 1, 2, and 3. Since dipswitch 1 has a value of 1, dipswitch

2 has a value of 2, and dipswitch 3 has a value of 4, the combination

of the three create a DMX value of 7. (See example below).

Set DMX address 1: Set DMX address 7:

Dip-switches # 1 = 1 Dip-switches # 1 = 1

2 = 2

3 = 4

= 7

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Mega Flash

DMX™ can be controlled via DMX-512 protocol.

The Mega Flash DMX™ is a two channel DMX

unit. The DMX address is set on the side panel of

the Mega Flash DMX™ Your unit and your DMX

controller require a standard 3-pin XLR connec-

tor for data input and data output (Figure 1). If you

are making your own cables, be sure to use standard two conductor

shielded cable (This cable may be purchased at almost all pro sound

and lighting stores). Your cables should be made with a male and

female XLR connector on either end of the cable. Also remember that

DMX cable must be daisy chained and can not be split.

Notice: Be sure to follow ﬁgures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 1

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR socket of the last unit

in your daisy chain to terminate the line. Using a cable terminator (ADJ

part number Z-DMX/T) will decrease the possibilities of erratic behav-

ior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR ﬁxtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Mega Flash DMX™ DMX Set Up

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 7 ©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 8

Mega Flash DMX™ Operating Instructions

Power Supply: This unit is available only in 120v. Before plugging

your unit in be sure the source voltage in your area matches the

required voltage for your American DJ® Mega Flash DMX.™

General Operation: This fixture is designed to operate as a stand

alone, sound-active unit, or in a Master/Slave configuration. It can

also operate via DMX controller. The Mega Flash DMX™ is ready to

be plugged in out of the box.

Duty Cycle:

Because the Mega Flash DMX™ can be used for continuous output

(ie while simulating lightning), it can build up intense heat. Due to the

build up of intense heat the unit should not run for 15 minutes con-

tinuously. After 15 minutes of continuous use, allow the unit to cool

for about fifteen minutes, this will greatly increase the lamp life and

insure product longevity.

Operating Modes:

Stand Alone and Sound Active Modes:

To run the strobe in stand alone mode, dipswitches #9 and #10 must

be in the “off” position. In stand alone mode the unit will function

as a normal strobe light. Rate (speed), and intensity (brightness),

are set directly on the unit. Note that these settings are made using

the knobs on the back of the unit. Once the settings are made they

can only be changed by physically adjusting the knobs on the unit.

Be aware of this if you plan on installing your strobe in a permanent

application, if your are not satisfied with your settings you will have to

physically remove the unit and adjust the knobs.

In sound active mode, dipswitch #9 must be in the “on” postion. The

dimming will still be controlled by the knob on the back of the unit.

But the beat of the music will control the flash speed. Note that these

settings are made using the knobs on the back of the unit. Once the

settings are made they can only be changed by physically adjusting

the knobs on the unit. Be aware of this if you plan on installing your

strobe in a permanent application, if your are not satisfied with your

settings you will have to physically remove the unit and adjust the

knobs.

Universal DMX Control: This mode allows you to use a universal

DMX-512 controller such as the American DJ® DMX Operator™ or

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 9

Show Designer.™

1. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-6 as well as the set-up procedures included with

your DMX controller.

2. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

3. Assign your desired address to the unit, and “flip” dipswitch #10

to the “on” postion.

4. The Mega Flash DMX™ uses two DMX channels. Channel 1 con

trols the flash speed and chanel 2 controls the dimmer. Use your

DMX controller to activate the various built-in patterns. See the

bottom of this page for the DMX traits.

5. For help operating in DMX mode consult the manual included

with your DMX controller.

NOTE: If running in Master/Slave address configuration while using a

DMX controller, follow the DMX address chart on page 12.

Mega Flash DMX™ Operating Instructions

Channel Value Function

1 0 - 255 FLASH SPEED

2 0 - 255 FLASH DIMMING

Mega Flash DMX™ DMX Traits

Mega Flash DMX™ Fuse and Lamp Replacement Cont.

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 10

Warning! Allow the lamp to discharge all current. Allow the

unit 24hrs. to discharge before changing the lamp. Stored

current can cause a very severe shock.

Warning: If after you have replaced the lamp or fuse and you contin-

ue to blow either one, STOP using the unit. Contact customer support

for further instructions, you may have to return the unit for servicing.

Continuing to use the unit may cause serious damage.

Fuse Replacement: Disconnect the unit’s main power supply.

Insert a standard flat head screw driver in to the fuse holder hous-

ing (located on the rear of the unit). Turn the screwdriver in a coun-

ter-clockwise direction to remove the fuse holder. Remove the old

fuse and discard it, replace the fuse with the same type. Insert the

fuse holder back into it’s housing and turn in a clockwise direction to

secure the holder in place.

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power and allow the fixture ample time

to cool before attempting to replace the lamp. Lamp replacement has

been made simple by incorporating a remove tray that is retained by a

single thumb screws. Again, please remember to always replace with

the exact same type lamp.

1. Be sure to follow the proper procedures when handling halogen

lamps. Never touch the new lamp with your bare fingers.

2. Unscrew and remove the four phillips screws located on the front

cover of the unit.

3. Located on each side of the lamp are white ceramic wire con-

nection blocks.

4. The ceramic block on the left side has one lamp wire connected

to the bottom of it, they are secured by one phillips screw each.

On the right side there are two lamp wires connected to the bot-

tom of the ceramic block.

5. NOTICE: When you disconnect the lamp wires to replace the

lamp, you will have to remember which wire went where. They

must be connected the same.

6. Push out the metal tabs on each side of the lamp, and pull out

the lamp as you do this. Replace the lamp with an exact match.

Connect the three wires to the ceramic blocks as they were when

you disconnected them. Reassemble in reverse order.

Halogen Lamp Warning! This fixture is fitted with

halogen lamps which are highly susceptible to dam-

age if improperly handled. Never touch the lamps

with your bare fingers as the oil from your hands will

shorten lamp life. Also, never move the fixture until

the lamps have had ample time to cool. Remember,

lamps are not covered under warranty conditions.

Mega Flash DMX™ Fuse and Lamp Replacement

Caution: Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American DJ® technician.

Replace with anything other than the specified part can damage your

unit and will void your manufactures warranty.

©American DJ® - www.americandj.com - Mega Flash DMX™ Instruction Manual Page 11

1-YEAR LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of one year (365

days) from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modiﬁed in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than

the American DJ® factory unless prior written authorization was issued to purchaser by

American DJ®; if the product is damaged because not properly maintained as set forth in

the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period speciﬁed above, American DJ® will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this war-

ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, includ-

ing warranties of merchantability or ﬁtness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of

merchantability or ﬁtness, shall apply to this product after said period has expired. The

consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

Mega Flash DMX™ Warranty

Model: Mega Flash DMX™

Voltage*: 120v~60Hz

Lamp: ZB-800 800w Strobe lamp

Fuse: 15A 250v

Dimensions: 15.9” (L) x 5.3” (W) x 4.1” (H)

Weight: 4.8 Lbs./ 2.2 Kgs.

Duty Cycle: 15 minutes on/off

Ventilation: Air Cooled

Warranty: 1 Year (365 Days)

*Voltage is preset at the factory and can not be changed by the user.

Please Note: Speciﬁcations and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Mega Flash DMX™ Specifications

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Fusion FX Bar 4 Bedienungsanleitung

American DJ

American DJ GP 250 Bedienungsanleitung

American DJ

American DJ SCENE SETTER Bedienungsanleitung

American DJ

American DJ Mine II Bedienungsanleitung

American DJ

American DJ DJ Spot LED Betriebsanleitung

American DJ

American DJ AVIATOR-SP8 Bedienungsanleitung

American DJ

American DJ Mega Bar UV100 Bedienungsanleitung

American DJ

American DJ LunarPod Bedienungsanleitung

American DJ

American DJ VioROLL LED Bedienungsanleitung

American DJ

American DJ Accu UFO Bedienungsanleitung

American DJ

American DJ Groove Wheel Bedienungsanleitung

American DJ

American DJ Flat Par Tri7X Bedienungsanleitung

American DJ

American DJ STAGE DESK-16 Bedienungsanleitung

American DJ

American DJ Snow Flurry Montageanleitung

American DJ

American DJ Aquarius Bedienungsanleitung

American DJ

American DJ Image 250 Bedienungsanleitung

American DJ

American DJ Flash-2C Bedienungsanleitung

American DJ

American DJ Rover LED Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ Roto-Balls Montageanleitung

American DJ

American DJ X-CALIBUR Bedienungsanleitung

American DJ

American DJ Galaxian Royale Bedienungsanleitung

American DJ

American DJ Super Jewel Bedienungsanleitung

American DJ

American DJ VioMoon LED Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung