American DJ Galaxian Move Bedienungsanleitung

User Instructions

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 2

Unpacking: Thank you for purchasing the Galaxian Move™ by Amer-

ican DJ®. Every Galaxian Move™ has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The Galaxian Move™ is a eight channel DMX intelligent,

moving head, red and green mini laser fixture. The Galaxian Move™

can operate as stand alone fixture or in a master/slave configuration.

The Galaxian Move™ has three operating modes; sound active, pre

programmed show, or controlled via DMX. For best results use fog or

special effects smoke to enhance the beams projections.

Customer Support: American DJ®provides a toll free customer sup-

port line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

ments or suggestions. For service related issue please contact Ameri-

can DJ®.Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ customer support.

PLEASE recycle the shipping carton whenever possible.

Galaxian Move™ General Introduction

Rev. 10/09

American DJ®

6122 S. Eastern Ave.

Los Angeles CA. 90040

www.americandj.com

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 4©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 3

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future

reference.

CAUTION IMPORTANT! When installing this projector, make sure

that it is mounted in a manner that prevents the audience from

looking directly into the beam, and the beam from striking the

audience.

Galaxian Move™ General Instructions Galaxian Move™ Safety Precautions

Safety Issues: This unit may “pop” the breaker if the maximum allotted

load of 2 amps is reached.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short. Do not attempt to oper-

ate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 20 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

• Green and Red Laser Diode

• 8 Channel DMX Control

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Fan Cooled

• Digital Display for Address and Function Setting

• 540° Pan / 270° Tilt

• UC3 Controller (Not Included)

• 4 Preprogrammed Shows

Galaxian Move™ Features

Galaxian Move™ Warranty Registration

The Galaxian Move™ carries a 90 day limited warranty. Please fill out

the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. If the unit

is under warranty you must provide a copy of your proof of purchase

invoice. Please contact American DJ®customer support for a R.A.

number.

DANGER

VISIBLE LASER RADIATION

-AVOID DIRECT EYE EXPOSURE

LASER DIODE

WAVELENGTH : 635~650 nm

Max Output : <4.9mW

Class IIIa Laser Product

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 5 ©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 6

Galaxian Move™ Laser Warnings and Safety

NON-INTERLOCKED HOUSING WARNING

The Galaxian Move™ contains high power laser devices internally.

Do not open the laser housing, due to the potential exposure to

unsafe levels of laser radiation. The laser power levels, if the unit is

opened, can cause instant blindness, skin burns and res.

STOP AND READ ALL LASER SAFETY DATA

OPERATION INSTRUCTIONS AND LASER SAFETY

The light source emitted from this product can potentially cause eye

injury if not set up and used properly. The light source emitted from a

laser is very different from any other light sources with which you may

be aware of. Laser light is thousands of times more concentrated

than any light from any other kind of light source. This concentration

of light can cause instant eye injuries, primarily by burning the retina

(the back of your eyeball contatining cells that are sensitive to light).

Even if you cannot feel “heat” from a laser beam, it can still poten-

tially injure or blind you or your audience. Even very small amounts

of laser beam light are potentially hazardous even at long distances.

Laser eye injuries can be sustained faster than you can blink.

Do not think that because this laser splits the laser beam into hun-

dreds of beams and that the laser beam is scanned out in high

speed, that an individual laser beam is safe for eye exposure. This

laser uses dozens of milliwatts of laser power (Class 3B levels inter-

nally) before it splits into multiple beams (Class 3R levels). Many of

the individual beams are potentially hazardous to the eyes.

Do not that because the laser light is moving, it is safe. This is not

true. Nor, do the laser beams always move. Since eye injuries can

occur instantly, it is critical to prevent even the smallest possibility of

any direct eye exposure. In the laser safety regulation, it is not legal

to aim Class 3R lasers in areas which people can get exposed. This

is true even if it is aimed below people’s faces, such as on a dance

oor.

Do not operate the laser without rst reading and understanding

all safety and technical data in this manual.

Always set up and install all laser effects so that all laser light is at

least 3 meters (9.8 feet) above the oor on which people can stand.

After setting up, and before public use, test laser to ensure proper

function. Do not use if any defect is detected. Do not use if laser

emits only one or two laser beams rather than dozens/hundreds, as

this could indicate damage to the diffraction grating optic, and could

allow emission of higher laser levels above Class 3R.

Do not point lasers at people or animals. Never look into the laser

aperture or laser beams.

Do not point lasers in areas in which people can potentially get

exposed, such as uncontrolled balconies, etc.

Do not point lasers at highly reective surfaces, such as windows,

mirrors and shiny metal. Even laser reections can be hazardous.

Never point a laser at aircraft, this is a federal offense.

Never point un-terminated laser beams into the sky.

Do not expose the output optic (aperture) to cleaning chemicals.

Do not use laser if the laser appears to be emitting only one or two

beams.

Do not use the laser if the housing is damaged, the housing is open,

or if the optics appear damaged in any way.

Never open the laser housing. The high laser power levels inside of

the protective housing can start res, burn skin and will cause instant

eye injury.

Never leave this device running unattended.

The operation of a class 3R laser show is only allowed if the show

is controlled by a skilled and well- trained operator, familiar with the

data included in this manual.

The legal requirements for using laser entertainment products vary

from country to country. The user is responsible for the legal require-

ments at the location/country of use.

Always use proper lighting safety cables when hanging lights and

effects overhead.

Galaxian Move™ Laser Warnings and Safety

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 8©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 7

Galaxian Move™ Laser Warninig Labels Galaxian Move™ Set Up

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Galaxian Move™.™ The American DJ®Galaxian Move™ is available

in a 115v and 230v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you xture. The voltage is select-

able via the switch located on the rear panel. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a sin-

gle controller, as long as all xtures and the controller are DMX com-

pliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. Therefore, the first fixture controlled by the

controller could be the last fixture in the chain. When a fixture is as-

signed a DMX address of 1, the DMX controller knows to send DATA

assigned to address 1 to that unit, no matter where it is located in the

DMX chain.

Data Cable (DMX Cable) Requirements (For

DMX and Master/Slave Operation): The Galaxian

Move™ can be controlled via DMX-512 protocol.

The Galaxian Move™ is a eight channel DMX unit.

The DMX address is set electronically using the

controls on the front panel of the unit. Your unit and

your DMX controller require a approved DMX-512

110 Ohm Data cable for data input and data output (Figure 1). We rec-

Figure 1

L aserApeture

C AUTI O N - C LASS 3R

LASER RAD IATIO N WHE N O PEN

AVO ID D IR EC T EYE E X PO SUR E

C AUTIO N - C LASS 3 R

LASER R ADI ATION WHEN OPEN

AVOI D DI REC T EYE EX PO SURE

D A N G E R

VI S I B L E LAS ER R AD IA T I O N

-AV O I D DI R E CT E YE E XP O S UR E

WAV E LE N G TH : 53 2 n m/G RE E N

: 65 0nm /R E D

Max . Outp ut : <4 . 9 mW

CL A S S I I I a LAS ER P R ODU C T

CO M P L IES W I T H C F R 1 0 4 0. 1 0 AND 10 40 . 1 1

Q C

P A S S

PA S S

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 9 ©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 10

Galaxian Move™ Set UpGalaxian Move™ Set Up

ommend Accu-Cable DMX cables. If you are making your own cables,

be sure to use standard 110-120 Ohm shielded cable (This cable may

be purchased at almost all professional sound and lighting stores).

Your cables should be made with a male and female XLR connector on

either end of the cable. Also remember that DMX cable must be daisy

chained and cannot be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 12©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 11

CAUTION IMPORTANT! When installing this projector, make sure

that it is mounted in a manner that prevents the audience from

looking directly into the beam, and the beam from striking the

audience.

System Menu: When making adjustments you can press

ENTER to conrm your setup or you can wait 8 seconds for

automatic setup. To exit without making any adjustments

press the MENU button.

ADDR - DMX Address Setting.

1. Tap the either the MENU, UP, or DOWN buttons until “ADDR”

is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER to set your desired DMX address.

SHND - This will let you choose one of the four prepro-

grammed shows. See show descriptions below.

1. Tap the either the MENU button until “SHND” is displayed,

press ENTER. Either “SH 1”, “SH 2”, “SH 3” or “SH 4” will be dis-

played.

2. Tap the UP or DOWN buttons to nd you desired show and

then press ENTER to conm and exit.

SHOWS:

Show 1 - For xtures placed on the oor, the tilt movement

angle is 210°

Show 2 - For fixtures fixed to the ceiling or truss, the tilt move-

ment angle is 90°.

Show 3 - For fixtures placed on a table. The beam is projected

at the audience’s direction; i.e. in front of the stage. Pan move-

ment angle (left to right to left) is 160°. Tilt movement angle is

90°.

Galaxian Move™ System MenuGalaxian Move™ System Menu Chart

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 14©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 13

Show 4 - For fixtures fixed to the ceiling. The beam is projected

at the audience’s direction; i.e. in front of the stage. Pan move-

ment angle (left to right to left) is 160°. Tilt movement angle is

90°.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Tap the MENU button until “SLND” is displayed, press

ENTER. Either “SL 1” or “SL 2” will be displayed.

2. Tap the UP or DOWN buttons until your desired setting is

displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can make one

xture the Master and then set the next xture to “SL 2”, the

xtures will now have contrast movement to each other.

SOUN - Sound Active mode.

1. Tap the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

“OFF” to deactivate sound active mode.

3. Press ENTER to conrm.

BLND - Blackout or Stand by mode.

1. Tap the MENU button until “BLND” is displayed, press

ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes”

is displayed, press ENTER to conm. The xture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and

press Enter.

I PAN - Pan Inversion

1. Tap the MENU button until “I PAN” is displayed, press ENTER.

Either “NO” or “I” will be displayed.

2. To activate the Pan inversion tap the UP or DOWN buttons

until “I” is displayed, press ENTER to conm. To deactivate Pan

inversion, select “NO” and press Enter.

I TLT - Tilt Inversion

1. Tap the MENU button until “I TLT” is displayed, press ENTER.

Either “NO” or “I” will be displayed.

2. To activate the Tilt inversion tap the UP or DOWN buttons

until “I” is displayed, press ENTER to conm. To deactivate Tilt

inversion, select “NO” and press Enter.

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Tap the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch off

after 10 seconds.

3. Press ENTER to conrm.

DISP - This function will reverse the display 180º.

1. Tap the MENU button until “dISP” is displayed, press ENTER.

2. Either “DISP” (display normal) or “DSIP” (display inversion) will

now be displayed. Press the UP or DOWN buttons to select one

or the other.

3. Press ENTER to conrm, or press the MENU button to return

Galaxian Move™ System Menu Galaxian Move™ System Menu

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 15 ©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 16

to the main menu.

TEST - This function will run a self test program. The test

program will test pan/tilt movement and colors.

1. Tap the MENU button until “TEST” is displayed, press ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running time

of the xture.

1. Tap the MENU button until “FHRS” is displayed, press

ENTER.

2. The display shows the running time of the unit. Press MENU

to exit.

VER - With this function you can display the version soft-

ware of the unit.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The display will now display the version of software. Press

MENU to exit.

RSET - Use this function to reset the unit.

1. Tap the MENU button until “RSET” is displayed, press ENTER.

2. The xture will now reset

Galaxian Move™ System Menu

Operating Modes: The Galaxian Move™ can operate in three

different modes. In each mode you can run the fixture as a

stand alone fixute or in a master/slave confiugration. This next

section will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

• Show mode -

The fixture will run one of four shows that you choose.

• DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation®Show

Designer.™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressing the ENTER button.

3. On the slave units tap the MENU button until “SLND” is dis-

played, and Press ENTER. Choose either “SL 1” or “SL 2” and

press ENTER. Please see page 11 for more info.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the pan, tilt, red and green

lasers individually, rotation, macros, and head movement speed. A

DMX controller allows you to create unique programs tailored to your

individual needs.

Galaxian Move™ Operation

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 17 ©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 18

1. The Galaxian Move™ is a eight DMX channel DMX fixture. See

pages 18-19 for detailed description of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 8-10 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 12 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttonS until you nd your desired show,

and press ENTER.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: This mode allows either a single unit or several units

linked together, to run one of four shows that you choose.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,

and press ENTER.

Galaxian Move™ Operation

Galaxian Move™ UC3 Control

Stand By Blackout the unit

Function 1. Strobe Red

2. Strobe Green

3. Strobe in Green/Red

Show

1-4

Rotation

Speed

Mode Sound (LED OFF) LED Blinking LED ON

Galaxian Move™ DMX Traits

Channel Value Function

10 - 255 PAN

2 0 - 255 TILT

3 RED LASER

0 - 7 OFF

8 - 15 ON/OPEN

16 - 239 SLOW - FAST

240 - 247 SOUND ACTIVE

248 - 255 ON/OPEN

4 GREEN LASER

0 - 7 OFF

8 - 15 ON/OPEN

16 - 239 SLOW - FAST

240 - 247 SOUND ACTIVE

248 - 255 ON/OPEN

5 LASER ROTATION

0 - 9 LASER OFF

10 - 120 COUNTER - CLOCKWISE FAST - SLOW

121 - 134 LASER OFF

135 - 245 CLOCKWISE SLOW - FAST

246 - 255 LASER OFF

6 MACROS

0 - 7 NO FUNCTION

8 - 49 RED COUNTER - CLOCKWISE

50 - 91 RED CLOCKWISE

92 - 133 GREEN COUNTER - CLOCKWISE

134 - 175 GREEN CLOCKWISE

176 - 217 RED & GREEN COUNTER - CLOCKWISE

218 -255 RED & GREEN CLOCKWISE

7 MOVEMENT

0 - 7 NO FUNCTION

8 - 28 MOVEMENT 1

29 - 49 MOVEMENT 2

50 - 70 MOVEMENT 3

71 - 91 MOVEMENT 4

©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 19 ©American DJ®- www.americandj.com - Galaxian Move™ Instruction Manual Page 20

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning

the internal and external lenses should be carried out periodically to

optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Clean the external optics with glass cleaner and a soft cloth every

20 days.

3. Always be sure to dry all parts completely before plugging the

unit back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-

mend cleaning on a monthly basis. Periodic cleaning will ensure lon-

gevity, and crisp beam output.

Galaxian Move™ Cleaning

Galaxian Move™ Trouble Shooting

Trouble Shooting: Listed below are a few common problems that

you may encounter, with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a standard 120v wall

outlet.

2. Be sure the external fuse has not blown. The fuse is located on

the rear panel of the unit.

3. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

Galaxian Move™ Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been

removed located the fuse holder located inside the power socket.

Insert a flat-head screw driver into the power socket and gently pry

out the fuse holder. Remove the bad fuse and replace with a new one.

The fuse holder has a built-in socket for a spare fuse be sure not to

confuse the spare fuse with active fuse.

Channel Value Function

7 MOVEMENT CONT.

92 - 112 MOVEMENT 5

113 - 133 MOVEMENT 6

134 - 154 MOVEMENT 7

155 - 175 MOVEMENT 8

176 - 196 MOVEMENT 9

197 - 217 MOVEMENT 10

218 - 238 MOVEMENT 11

239 - 255 MOVEMENT 11

8 MOVEMENT SPEED

0 - 239 FAST - SLOW

Galaxian Move™ DMX Traits

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ MINI-Gressor II Bedienungsanleitung

American DJ

American DJ Verti-Pro II Bedienungsanleitung

American DJ

American DJ Revo XPress Bedienungsanleitung

American DJ

American DJ Rover 250 Bedienungsanleitung

American DJ

American DJ Raider Bedienungsanleitung

American DJ

American DJ Micro Wash RGBW Bedienungsanleitung

American DJ

American DJ Quadra Force/Sys Bedienungsanleitung

American DJ

American DJ Concept 1 Bedienungsanleitung

American DJ

American DJ Majestic LED Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ H2O 2 Bedienungsanleitung

American DJ

American DJ Groove Wheel Bedienungsanleitung

American DJ

American DJ Aquarius II Bedienungsanleitung

American DJ

American DJ Rolling Star II Bedienungsanleitung

American DJ

American DJ Sunray Tri LED DMX Bedienungsanleitung

American DJ

American DJ Mega Flash DMX Bedienungsanleitung

American DJ

American DJ Reflex Bedienungsanleitung

American DJ

American DJ Accu Spot Pro Bedienungsanleitung

American DJ

American DJ Sunray-150D Bedienungsanleitung

American DJ

American DJ Space Balls Bedienungsanleitung

American DJ

American DJ Inno Roll LED Bedienungsanleitung

American DJ

American DJ Stingray Bedienungsanleitung

American DJ

American DJ H2O Bedienungsanleitung

American DJ

American DJ SATURN 4 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung