American DJ Accu Spot Pro Bedienungsanleitung

American DJ®

6122 S. Eastern Ave.

Los Angeles CA. 90040

www.americandj.com

1/08

User Instructions

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 2

American DJ®

Accu Spot Pro

Table of Contents

Unpacking......................................................................3

Introduction....................................................................3

Customer Support......................................................................3

Safety Precautions......................................................................4

Handling Precautions..................................................................5

Discharge Lamp Warnings..........................................................5

Registration......................................................................6

Features.........................................................................6

Controls and Functions..............................................................7

Set-Up.............................................................................10

System Menu............................................................................13

Editing Program.........................................................................31

Error Codes...............................................................................36

Operating Modes.......................................................................38

Lamp and Fuse Replacement...................................................40

DMX Traits.................................................................................42

Gobo Replacement...................................................................46

Cleaning..................................................................47

Trouble Shooting.......................................................................47

Warranty.................................................................48

Specifications....................................................................51

American DJ®

Unpacking: Thank you for purchasing the Accu Spot Pro by Ameri-

can DJ®. Every Accu Spot Pro has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The Accu Spot Pro is a sixteen channel, moving head,

intelligent DMX fixture. The fixture can operate in three different oper-

ating modes; stand alone, sound-active, or in a Master/Slave configu-

ration. The Accu Spot Pro comes with several built in programs that

can be used, while operating as a stand alone unit or when used in

multiples linked in a master/slave configuration. For best results use

fog or special effects smoke to enhance the beams projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the lamp.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Accu Spot Pro General Information

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 47 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Accu Spot Pro Safety Precautions

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 4American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 3

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 5

Accu Spot Pro Discharge Lamp Warning

This fixture is fitted with a discharge lamp which

is highly susceptible to damage if improperly

handled. Never touch the lamp with your bare fin-

gers as the oil from your hands will shorten lamp

life. Also, never move the fixture until the lamps

have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible (Uses 14 DMX Channels)

• Independent Gobo and Color Wheels

• 2 Gobo Wheels - Wheel 1: 6 Rotating Gobos + Spot

Wheel 2: 7 Static + Spot- All Replaceable

• 8 Colors, Plus White - With Rainbow

• Prism Wheel with Macros - 3 Facet Prism & Trapezoid Prism

• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active

• Internal Microphone

• ZB-MSD250 Discharge Lamp, 250w

• Edit and Save Scenes into the Memory

• Manual Focus Lens

• Variable Strobe (1-12 fps)

• Switchable 540˚ to 630˚ Pan Movement

• 265˚ Tilt Movement

• Digital Display for Address and Function Setting

Accu Spot Pro Features

The Accu Spot Pro carries a one year limited warranty. Please fill out

the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper

at the shippers cost.

Accu Spot Pro Product Registration

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 6

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Accu Spot Pro General Instructions

This unit emits intense UV radiation which is harmful to the eyes and

skin. The intense luminance of the lamp can cause severe damage

to the retina. Never operate this unit without it’s covers, these covers

have been specially designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking

directly into the lamp at all times.

Avoid switching the xture on and off repeatedly in short intervals as

this will reduce lamp life and intensity.

To achieve the intensity associated with discharge lamps, these lamps

use gas sealed in a high pressure environment to emit a brilliant output.

Due to the high pressure involved with the construction of the lamp,

the lamp may explode during prolonged extensive use. This risk is

increased with age, added care is encouraged when dealing with older

lamps. Extreme caution should be used when operating this or any

xture tted with a gas discharge lamp. Never open this unit while in

use.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ®.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Accu Spot Pro Handling Precautions

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 8American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 7

Accu Spot Pro Controls and Functions

REAR

FRONT

Accu Spot Pro Controls and Functions

1. Lens Assembly - This is a high quality lens that is focused by

using the Lamp Optimization in DMX Mode.

2. Software Update Input Jack - This jack is used to update the

latest software version into the unit.

3. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

4. Mode/ESC Button - This button is used to exit menus and to scroll

backwards through certain menus only.

5. Up Button - This button is used to scroll forward when navigating

through the system menu.

6. Down Button - This button is used to scroll backwards when navi-

gating through the system menu.

7. Enter Button - This button is used to select and conrm a func-

tion when working in the system menu. It is also used to exit certain

menus.

8. Carrying Handles - The includes built-in carrying handles. Be sure

to always handle the unit by the built-in handles. Never lift or carry-

ing the unit by head or yoke. Pulling on or transporting the unit by the

moving head may severely damage the unit and will void the unit war-

ranty.

7. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active mode. This microphone is designed

to receive low frequency sounds only, tapping on the microphone and

high pitch sounds may not trigger the unit.

9. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX xture, or transmit a Master/Slave signal

to the next Accu Spot Pro in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Terminator” on page 11.

10. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

11. Fuse Holder - This housing stores a 8 amp (4 amp 220v) GMA pro-

tective fuse. Never defeat the fuse, the fuse is designed to protect the

65 7 9 108

Accu Spot Pro Controls and Functions

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 9

electronics in the event of severe power uctuations. Always be sure

to replace the fuse with an exact match as the one being replaced,

unless otherwise told to do so by an authorized American DJ®service

technician.

12. Power Cord Inlet - This unit is equipped with a removable I.E.C.

power cord. Be sure to only use the power cord included with the

unit, this cord is designed to match the electrical requirements of the

unit. Other cords may cause the unit to overheat or malfunction. Volt-

age may vary from venue to venue, when connecting this unit to a

power supply be sure to connect to a matching power outlet. Never

use this xture if the ground prong has been removed or broken off.

The ground prong is designed to reduce the risk of re or electrical

shock in the event the unit suffers from an internal short.

13. Cooling Fan - This unit is equipped with three high velocity vari-

able fans to aid in the cooling process. These fans are designed to

vary their velocity at different operating temperatures, to provide

better cooling when the unit reached higher operating temperatures

associated with long usage. Be sure to never obstruct the cooling fans

during normal usage. Also, be sure to keep the vents clean at all times.

A blocked or malfunctioning cooling system may shorten lamp life and

unit reliability.

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 10

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Accu Spot 300.™ The American DJ®Accu Spot Pro is available in a

120v and 220v version. Because line voltage may vary from venue to

venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you xture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Accu Spot Pro

can be controlled via DMX-512 protocol. The Accu

Spot Pro is a fourteen channel DMX unit. The DMX

address is set electronically using the controls on

the side panel of the unit. Your unit and your DMX

controller require a standard 3-pin XLR connec-

tor for data input and data output (Figure 1). If you

are making your own cables, be sure to use standard two conductor

Accu Spot Pro Set Up

Figure 1

shielded cable (This cable may be purchased at almost all professional

sound and lighting stores). Your cables should be made with a male

and female XLR connector on either end of the cable. Also remember

that DMX cable must be daisy chained and cannot be split.

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 11

Accu Spot Pro Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Accu Spot Pro Set Up

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 12

Accu Spot Pro System Menu

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 14American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 13

Accu Spot Pro System Menu

ADDRESS MENU -

AOO1 - A511 (Value) - This is where you set the DMX address of

the unit.

TEST MENU -

T-01 - T-XX (Test) - Tests the functions of each channel. There

are fourteen channels. Note: Some channels cannot be

tested.

PLAY MENU -

RUN - Runs the unit as a “master” in a Master/Slave congura-

tion or as a Stand Alone unit. The unit will run a internal pro-

gram.

AUDI (Audio) - Runs the unit as a “master” in a Master/Slave

conguration or as a Stand Alone unit in sound active mode.

AUTO - This is a precaution mode in case the DMX signal is lost.

There are four settings to choose from:

• “Hold” - This is the default setting, which in case the signal is

lost the xture will “hold” at the last setting.

• “Close” - The xture will return to its “home” standing.

• “Auto” - The xture will go into Auto mode and run a pre-pro-

grammed show.

• “Audi” - The xture will go into Sound Active mode.

LAMP MENU -

ON/OFF - Manually switch the lamp “on” and “off”.

RESE (RESET) MENU -

ALL - Resets all the motors in the unit.

SCAN - Resets the motors that control pan/tilt.

COLR (Color) - Resets the color motors.

ADDR

AXXX A001

Indicate the staring DMX address

A001 also is the setting for slave

TEST

T-01~T-XX

Automatically test the function

RUN

MSTR/ALON

Runs fixture as “master” or “alone” for auto

AUDI

MSTR/ALON

Runs fixture as “master” or “alone” for

audio

PLAY

AUTO

Clos/Hold/Auto/Audi

Runs fixture for no DMX

LAMP

ON/OFF

Manually switches lamp “on” and “off”

ALL

Reset all motors and returns fixture to home

SCAN

Reset only motors for pan/tilt

COLR

Reset only motors for colors

GOBO

Reset only motors for gobo and rotation

SHTR

Reset only motors for shutter and/or dimmer

RESE

OTHR

Reset other motors

LIFE

0000~9999

Displays the total fixture running time

LAMP

0000~9999

Displays a lamps running time

TIME

CLMP

Clear lamp running time

RPAN

ON/OFF

Reverses the pan movements

RTLT

ON/OFF

Reverses the tilt movements

FINE

ON/OFF

Switch between 16 bit/8 bit

DEGR

630/540

Pan degree select

MIC

M-XX

Mic sensitivity

VALU

D–XX D-00 (DXXX)

Display the DMX512 value of each channel

D ON

ON/OFF

Display turn off after 2mins

DISP

FLIP

ON/OFF

This function will reverse the display 180

LAAU

ON/OFF

Automatic lamp start with power

RDMX

ON/OFF

Change DMX address via external controller

DLOF

ON/OFF

Switch lamp via DMX

DLAY

D–XX D-05

Lamp on delay time

SPOT

ON/OFF

Lamp optimization

DFSE

ON/OFF

Resets all the fixture functions to default

FEED

ON/OFF

Pan/tilt feedback (error correction) on/off

SPEE

SP-1/SP-2

Movement Mode Select

DIMM

Slow/Fast

Dimmer speed

FANS

HIGH/AUTO

Fan’s mode select

VER

V1.0~V9.9

Software version

CODE

CXXX

Fixture code *code is “C050”

SPEC

ADJU

CH01~CH30

XXXX(-128~127)

Motor Calibration

STEP

S–01 ~S–48

Set the amount of your program

C–01~C–30

0 1 XX(00~FFH)

3 0 XX(00~FFH)

Edit the channels of each scene

TIME

T XXX(001~999)

Time for each scene

SCXX

CEDT

ON/OFF

Edit program via controller

REC.

RE.XX

Auto Save

EDIT

RUN

ON/OFF

Program test

Accu Spot Pro System Menu

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 16American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 15

GOBO - Resets the gobo and rotation motors.

SHTR - Resets the shutter/dimmer motors.

OTHR - Resets all the other motors.

TIME MENU -

LIFE - Displays the xtures total running time.

LAMP - Displays the lamp running time.

CLMP - Clears the lamp running time.

RPAN (REVERSE PAN) MENU -

ON/OFF - When “On” is chosen it will reverse the pan.

RTILT (REVERSE TILT) MENU -

ON/OFF - When “On” is chosen it will reverse the tilt.

FINE MENU -

ON/OFF - Switch between 16bit (On) and 8bit (Off).

DEGR MENU -

630/540 - Switch the degree of the Pan between 630 and 540.

MIC MENU -

M-01-M-70 - With this function you can make the internal mic

more or less sensitive to sound.

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON (Display On) - Turns digital display off after 2 mins.

FLIP - “Flips” the digital display 180º.

SPEC MENU -

LAAU - Automatic lamp start with power.

RDMX - Lets you adjust the DMX address via external controller.

DLOF - Switch lamp on via DMX.

DLAY - Set a delay time for the lamp.

SPOT - This provides a spot beam for lamp optimization.

DFSE (Default Settings) - Resets the unit to the default settings.

FEED - Pan/Tilt feedback (error correction) on/off.

SPEE - Select the movement speed.

DIMM - Select the dimmer speed.

FANS - Select the fans run mode.

VER (Version) - Displays the software version

ADJU - Fixture code is “C050”.

CH01~CH30 for motor calibration.

EDIT MENU -

STEP (S-01 - S-48) - These are the steps slots that you write

your programs into. There are at total of 48 steps. See edit pro-

gram, page 25.

SCXX (SC01 - SC30) - These are the scenes that are stored in

your program. There are a total of 30 scenes.

Submenus:

C-01~C-30 - Edit the channels of each scene.

TIME - Set the Time for each scene.

CEDT - Edit the program via external controller.

REC - This will auto save your custom program.

RUN - This will run your custom program.

Accu Spot Pro System Menu

4. Press MODE/ESC to exit.

PLAY MAIN MENU -

RUN Run the unit in an Auto mode as a “master” in a

Master/Slave conguration, or as a stand alone unit -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “RUN” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice by pressing ENTER, “PASS” will ash

in the display and xture will begin its function.

AUDI Run the unit in Sound Active mode as a “master”, or

as a stand alone unit -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “AUDI” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice and press ENTER.

AUTO This is a precaution mode in case you lose the DMX

signal. The xtue has 4 modes to choose from, please see

page 14 for a description of the 4 modes -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “AUTO” is displayed, press ENTER.

4. Now you can choose between “CLOSE”, “HOLD” “AUTO”, or

“AUDI”. “HOLD” is the default setting.

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 18American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 17

Accu Spot Pro System Menu

On-Board System Menu.

The Accu Spot Pro comes with an easy

to navigate system menu. This next section will detail the functions of

each command in the system menu.

To access the main menu press the MODE/ESC button (7) on the front

of the unit. Tap the UP (5) or DOWN (6) butons until you reach function

you wish to change. When you reach the function you wish to change

tap the ENTER button. Again, tap the UP or DOWN buttons to change

the function. Once your changes are made, tap the ENTER button to

lock the change in the system, if the ENTER button is not selected

within eight seconds the system will automatically return to menu sec-

tion. To exit without making any changes tap the MODE/ESC button

(4).

Accu Spot Pro System Menu

ADDR MAIN MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “ADDR” is displayed, press ENTER.

4. Now the display will show “A001”. Adjust the DMX address

by pressing the UP or DOWN buttons.

5. Press ENTER to conrm.

6. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DN buttons to change the DMX start address.

TEST MAIN MENU -

TEST - This will test the functions of each channel.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “TEST” is displayed, press ENTER.

3. The display will show “T-01”. You can now press the up

button and test the different channels.

Accu Spot Pro System Menu

American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 20American DJ®- www.americandj.com - Accu Spot Pro Instruction Manual Page 19

4. Press ENTER to reset the pan/tilt motors, or press MODE/

ESC to cancel and return to the main menu.

COLR - When you activate this reset function, the xture

will only reset the color wheel motor.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “COLR” is displayed.

4. Press ENTER to reset the color wheel motor, or press MODE/

ESC to cancel and return to the main menu.

GOBO - When you activate this reset function, the xture

will only reset the gobo wheel motor.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “GOBO” is displayed.

4. Press ENTER to reset the gobo wheel motor, or press MODE/

ESC to cancel and return to the main menu.

SHTR - When you activate this reset function, the xture

will only reset the shutter/dimmer motor.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SHTR” is displayed.

4. Press ENTER to reset the shutter/dimmer motor, or press

MODE/ESC to cancel and return to the main menu.

OTHR - When you activate this reset function, the xture

will reset all other motors that are not listed in RESET

menu.

Accu Spot Pro System Menu

5. Select the mode that you want the xture to run in case of a

lost DMX signal and press ENTER.

LAMP MAIN MENU -

ON/OFF - With this function you can manually switch the

lamp on and off.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “LAMP” is displayed, press ENTER.

3. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

4. Press ENTER to conrm.

5. Press MODE/ESC to return to the main menu.

RESE MAIN MENU -

ALL - When you activate the reset function, the xture will

begin the reset motion.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “ALL” is displayed.

4. Press ENTER to reset all motors, or press MODE/ESC to

cancel and return to the main menu.

SCAN - When you activate this reset function, the xture

will only reset the pan/tilt motor.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SCAN” is displayed.

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ RollerTron Bedienungsanleitung

American DJ

American DJ Jewel Bedienungsanleitung

American DJ

American DJ Flash Matrix Hub Bedienungsanleitung

American DJ

American DJ LED Vision Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ BU-350 Bedienungsanleitung

American DJ

American DJ Mega Flash DMX Bedienungsanleitung

American DJ

American DJ Orbitron Bedienungsanleitung

American DJ

American DJ Sunray LED Bedienungsanleitung

American DJ

American DJ Torch Light Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 EX Bedienungsanleitung

American DJ

American DJ LTS-2 Bedienungsanleitung

American DJ

American DJ Flash Duo Bedienungsanleitung

American DJ

American DJ Fusion Scan 250EX Bedienungsanleitung

American DJ

American DJ Micro Wash RGBW Bedienungsanleitung

American DJ

American DJ H2O Bedienungsanleitung

American DJ

American DJ Fun Factor LED Bedienungsanleitung

American DJ

American DJ Flash Tube Buffer Bedienungsanleitung

American DJ

American DJ Pinspot LED RC Bedienungsanleitung

American DJ

American DJ T4 Bedienungsanleitung

American DJ

American DJ Fan-1000 Bedienungsanleitung

American DJ

American DJ DJ Scan/RG Bedienungsanleitung

American DJ

American DJ RotoPod Bedienungsanleitung

American DJ

American DJ Bubble Blast Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung