American DJ Inno Roll LED Bedienungsanleitung

American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 2

Inno Roll LED General Information

Unpacking: Thank you for purchasing the Inno Roll LED by Ameri-

can DJ®. Every Inno Roll LED has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The Inno Roll LED is a 8 channel DMX intelligent LED

scanner. The Inno Roll LED has three operating modes; a sound active,

show mode, DMX controlled. The Inno Roll LED can operate as a stand

alone fixture or in a Master/Slave configuration. For best results use

fog or special effects smoke to enhance the beams projections.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

User Instructions

Rev. 6/12

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 20 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

Inno Roll LED Safety Precautions

American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 4American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 3

• 8 DMX Channels

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 6 Preprogrammed Shows

• 8 Colors + White

• 6 Replaceable Gobos + Spot

Inno Roll LED Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ®.

During operation the housing may become extremely hot. Avoid touch-

ing the unit with bare hands while in use.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Inno Roll LED Handling Precautions

Inno Roll LED Warranty Registration

The Inno Roll LED carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact American DJ® cus-

tomer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Inno Roll LED General Instructions

American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 6American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 5

Power Supply: The American DJ®Inno Roll LED contains a automatic

voltage switch, which will auto sense the voltage when it is plugged

into a power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Inno Roll LED can be controlled via DMX-512 proto-

col. The Inno Roll LED is a 8 channel DMX unit. The DMX address is

set electronically using the controls on the front panel of the unit. Your

unit and your DMX controller require a approved DMX-512 110 Ohm

Data cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If you

are making your own cables, be sure to use stan-

dard 110-120 Ohm shielded cable (This cable may

be purchased at almost all professional sound and

lighting stores). Your cables should be made with

a male and female XLR connector on either end of

the cable. Also remember that DMX cable must be

Inno Roll LED Set Up

Figure 1

daisy chained and cannot be split.

Inno Roll LED Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 7 American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Inno Roll LED Set Up Inno Roll LED System Menu

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 10American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 9

Inno Roll LED System Menu

ADDR - DMX Address Setting.

1. Press the MENU button until “ADDR” is displayed, press

ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

When you have found your desired DMX address press ENTER

then press and hold the MENU button for at least 3 seconds to

set your desired DMX address.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is

displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures will

now have contrast movement to each other.

SHND: SH 0-SH6 - Show modes 0-6 (Factory programs).

Show mode can run with or without sound active mode.

1. Press the MENU button until “SHND” is displayed, press

ENTER.

2. “Sh X” will now be displayed, “X” representing a number

between 0-6. Programs 1-6 are factory programs, while “Sh 0”

is random mode. Press the UP or DOWN buttons to nd your

desired show.

3. When you have found your desired show press ENTER, then

press and hold the MENU button for at least 3 seconds to acti-

vate. After you have set your desired show, it can be changed

at any time using the UP or DOWN buttons.

SPLC - Split Color mode. With this mode active, color

output will be split and whole. This mode needs to be acti-

vated for the split color to work in DMX Mode.

1. Press the MENU button until “SPLC” is displayed, press

ENTER.

2. The display will show either “YES” or “NO”. Press the UP or

DOWN buttons to select “YES” to activate split color mode, or

“NO” to deactivate split color mode.

3. Press ENTER to conrm.

DCAL - In this mode you can adjust the LED output inten-

sity.

1. Press the MENU button until “DCAL” is displayed, press

ENTER.

2. A number between 50-100 will be displayed. Press the UP

or DOWN buttons to adjust the LED output intensity. 50 being

medium intensity, and 100 being full intensity.

3. When you have found your desired setting press ENTER to

conrm.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

“OFF” to deactivate sound active mode.

3. Press ENTER, then press and hold the MENU button for at

least 3 seconds to activate.

Inno Roll LED System Menu

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 11 American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 12

DISP - This function will reverse the display 180º.

1. Press the either the MENU button until “DISP” is displayed,

press ENTER.

2. Press the UP button to select “DSIP” to “ip” the display, or

“DISP” to change the display back.

3. Press ENTER to conrm.

PAN - Pan Inversion

1. Press the MENU button until “PAN” is displayed, press

ENTER. Either Yes or No will be displayed.

2. To activate the Pan inversion press the UP or DOWN buttons

until YES is displayed, press ENTER to conm. To deactivate

Pan inversion, select NO and press Enter.

TEST - This function will run a self test program. The test

program will test pan/tilt movement and colors.

1. Press the MENU button until “TEST” is displayed, press

ENTER.

2. The xture will now run a self test.

TEMP - With this function you can check the temperature

of the xture.

1. Press the MENU button until “TEMP” is displayed, press

ENTER.

2. The temperature of the xture will now be displayed. Press

MENU to exit.

FHRS - With this function you can display the running time

of the unit.

Inno Roll LED System Menu

SENS - In this mode you can adjust the sound sensitivity.

1. Press the MENU button until “SENS” is displayed, press

ENTER.

2. A number between 0-100 will be displayed. Press the UP or

DOWN buttons to adjust the sound sensitivity. 0 being the least

sensitive, and 100 being the most sensitive.

3. When you have found your desired setting press ENTER to

conrm.

BLND - Blackout or Stand by mode.

1. Press the MENU button until “BLND” is displayed, press

ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes”

is displayed, press ENTER to conm. The xture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and

press Enter.

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch o

after 10 seconds.

3. Press ENTER to conrm. To make the LED display reappear

after it has turned o, press any button.

Inno Roll LED System Menu

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 13 American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 14

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - With this function you can display the version soft-

ware of the unit.

1. Press the MENU button until “VER” is displayed, press

ENTER.

2. The software version will now be displayed. Press MENU to

exit

PROD - Pro defaults.

1. Press the MENU button until “PROD” is displayed, press

ENTER.

2. The display will show either “YES” or “NO”. Press the UP or

DOWN buttons to select “YES” to reset back to PRO default

settings, or “NO” to not reset to PRO defaults.

3. Press ENTER to conrm.

RSET - Use this function to reset the unit.

1. Press the MENU button until “RSET” is displayed, press

ENTER.

2. The xture will now reset,

Inno Roll LED System Menu Inno Roll LED Color & Gobo Adjustment

To enter the Color/Gobo wheel adjustment submenu, press the

ENTER button for at least 5 seconds. In this submenu you are able to

adjust the original position of the gobo wheel and color wheel.

COLO - Adjustment of the color wheel.

1. Press the ENTER button for at least 5 seconds, then press the UP

or DOWN buttons so that “COLO” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

GOBO - Adjustment of the gobo wheel.

1. Press the ENTER button for at least 5 seconds, then press the UP

or DOWN buttons so that “GOBO” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 16American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 15

Inno Roll LED Operation

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-7 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER. Tap the UP or DOWN buttons so that “ON” is dis

played and press ENTER.

2. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: This mode allows either a single unit or several units

linked together, to run one of 6 shows that you choose.Show mode

can run with or without sound active mode.

1. Press the MENU button until “SHND” is displayed, and press

ENTER.

2. Press the UP or DOWN buttons until you nd your desired show,

press ENTER, then press and hold the MENU button for at least 3

seconds to activate. After you have set your desired show, it can

be changed at any time using the UP or DOWN buttons.

Inno Roll LED UC3 Control

Stand by Blackout the unit

Function 1. Strobe in synchronization

2. strobe in desynchronization

3. Strobe by music

Select Movement

1-6

Color/Gobo selection

1. Press shortly for

color change.

2. Hold on for

Gobo change

Mode Sound

(LED OFF)

Movement

(LED Blinking)

Gobo/Color

(LED ON)

Operating Modes: The Inno Roll LED can operate in three dif-

ferent modes. In each mode you can run the fixture as a stand

alone fixture or in a master/slave confiugration. This next sec-

tion will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

•Show mode -

The fixture will run one of six shows that you choose.

•DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation®Show

Designer.™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressiing the ENTER button.

3. On the slave units tap the MENU button until “SLND” is dis-

played, and Press ENTER. Choose either “SL 1” or “SL 2” and

press ENTER. See page 9 for more info.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The Inno Roll LED is an eight DMX channel DMX fixture. See

pages 16-18 for detailed description of the DMX values and traits.

Inno Roll LED Operation

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 17 American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 18

Inno Roll LED 8 Channel Mode

Channel Value Function

1 0 - 255 PAN 0° - 180°

2 TILT

0 - 9 STOP

10 - 120 CLOCKWISE ROLL FAST - SLOW

121 - 134 STOP

135 - 245 COUNTER CLOCKWISE ROLL

SLOW - FAST

246 - 255 STOP

3 STROBE

0 - 7 BLACKOUT

8 - 15 OPEN

16 - 131 STROBING SLOW - FAST

132 - 139 OPEN

140 - 181 FAST OPEN - SLOW CLOSE

182 - 189 OPEN

190 - 231 FAST CLOSE - SLOW OPEN

232 - 239 OPEN

240 - 247 RANDOM STROBE

248 - 255 OPEN

4 COLOR WHEEL

0 - 14 WHITE

15 - 21 WHITE/RED

22 - 28 RED

29 - 35 RED/ORANGE

36 - 42 ORANGE

43 - 49 ORANGE/YELLOW

50 - 56 YELLOW

57 - 63 YELLOW/GREEN

64 - 70 GREEN

71 - 77 GREEN/CYAN

78 - 84 CYAN

85 - 91 CYAN/MAGENTA

92 - 98 MAGENTA

99 - 105 MAGENTA/LIGHT BLUE

106 - 112 LIGHT BLUE

113 - 119 LIGHT BLUE/PURPLE

120 - 127 PURPLE

Inno Roll LED 8 Channel Mode

Channel Value Function

4 COLOR WHEEL CONT.

128 - 191 CLOCKWISE ROTATION FAST - SLOW

192 - 255 COUNTER-CLOCKWISE ROTATION

SLOW - FAST

5 GOBO WHEEL

0 - 9 OPEN

10 - 18 GOBO 1

19 - 27 GOBO 2

28 - 36 GOBO 3

37 - 45 GOBO 4

46 - 54 GOBO 5

55 - 63 GOBO 6

64 - 74 GOBO 1 SHAKE

75 - 85 GOBO 2 SHAKE

86 - 95 GOBO 3 SHAKE

96 - 106 GOBO 4 SHAKIE

107 - 116 GOBO 5 SHAKE

117 - 127 GOBO 6 SHAKE

128 - 189 CLOCKWISE ROTATION FAST - SLOW

190 - 193 STOP

194 - 255 COUNTER-CLOCKWISE ROTATION

SLOW - FAST

6 GOBO ROTATION

0 - 127 GOBO INDEXING

128 - 189 CLOCKWISE ROTATION FAST - SLOW

190 - 193 STOP

194 - 255 COUNTER-CLOCKWISE ROTATION

SLOW - FAST

7 0 - 255 DIMMER 0% - 100%

8 RESET/BLACKOUT

0 - 69 NO FUNCTION

70 - 79 ENABLE BLACKOUT WHILE PAN/TILT MOVE

80 - 89 DISABLE BLACKOUT WHILE PAN/TILT MOVE

90 - 99 ENABLE BLACKOUT WHILE COLOR CHANGE

100 - 109 DISABLE BLACKOUT WHILE COLOR CHANGE

110 - 119 ENABLE BLACKOUT WHILE GOBO CHANGE

120 - 129 DISABLE BLACKOUT WHILE GOB CHANGE

American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 19 American DJ®- www.americandj.com - Inno Roll LED Instruction Manual Page 20

This unit comes with interchangable gobos. When changing

the gobos please be very careful. Follow the instructions below,

and see the gure pictures on the next page.

Caution! Never open the unit when in use. Always disconnect

the main power before attempting to change the gobos.

1. Start by standing the fixture upright so that it is sitting on the

bottom handles. Unscrew the two phillips screws located on

the front panel just underneath the air vents.

2. Carefully remove the front panel to access the gobo wheel.

3. Rotate the gobo wheel with your hand until you find the gobo

you would like to change.

4. Using a pair of needle nose pliers, grab the retainer ring that

holds the gobo in place and remove the ring. You can also

remove the gobo by carefully pushing the gobo from the bot-

tom, pushing it up and out. Do this carefully so that you don’t

lose the retainer ring and the gobo.

5. Once you have removed the gobo carefully insert your new

gobo and reinsert the retainer ring.

6. Reassemble the unit.

Inno Roll LED Gobo ReplacementInno Roll LED 8 Channel Mode

Channel Value Function

8 RESET/BLACKOUT

130 - 199 NO FUNCTION

200 - 209 RESET ALL

210 - 239 NO FUNCTION

240 - 255 SOUND ACTIVE

To access the split colors, split color mode must be activated in

the system menu. Please see page 10.

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Starball II Bedienungsanleitung

American DJ

American DJ Accu Spot 575 Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ Rover Bedienungsanleitung

American DJ

American DJ SS-DMX19CTM Bedienungsanleitung

American DJ

American DJ Gobo Flash 4 Bedienungsanleitung

American DJ

American DJ Fire Bowl Bedienungsanleitung

American DJ

American DJ Mobile Beam Bedienungsanleitung

American DJ

American DJ Inno Spot Elite Bedienungsanleitung

American DJ

American DJ Flash Matrix Hub Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

American DJ

American DJ Flash-2C Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Montageanleitung

American DJ

American DJ Color Gem Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ Pro Par56 CWWW Bedienungsanleitung

American DJ

American DJ Mighty Scan Bedienungsanleitung

American DJ

American DJ Double Feature Bedienungsanleitung

American DJ

American DJ Atmospheric RG LED Bedienungsanleitung

American DJ

American DJ Quadra Force/Sys Bedienungsanleitung

American DJ

American DJ LED Quest Bedienungsanleitung

American DJ

American DJ Vortex Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ Saturn Tri LED Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung