American DJ Image 250 Bedienungsanleitung

User Instructions

American DJ

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

Customer Support:

American DJ®provides a toll free customer support line, to provide set

up help and to answer any question should you encounter problems

during your set up or initial operation. You may also visit us on the web

at www.americandj.com for any comments or suggestions. For service

related issue please contact American DJ®. Service Hours are Monday

through Friday 9:00 a.m. to 5:00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ.

PLEASE recycle the shipping carton when ever possible.

Safety Issues: This unit may blow a fuse if the maximum allotted

load of 5 amps is reached. If the fuse needs replacement, always

replace the fuse with same exact type that was remove, unless oth-

erwise instructed by an authorized American DJ®service technician.

Use of a different type fuse from that which is recommended may

cause fire or electric shock and will void the manufactures warranty.

Image 250™ Unpacking

©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 2

Image 250™ Introduction

Thank you for purchasing the Image 250™ by American DJ®. Every

Image 250™ has been thoroughly tested and has been shipped in

perfect operating condition. Carefully check the shipping carton for

damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your unit for any damage and be sure

all equipment necessary to operate the system has arrived intact. In

the event damage has been found or parts are missing, please contact

our toll free customer support number for further instructions. Please

do not return the unit to your dealer without rst contacting customer

support.

Rev. 10/07

Introduction: Thank you for purchasing the Image 250™ by American

DJ®. For your convenience the Image 250™ has been lamped and is

ready to be used, there is no assembly necessary. There are 7 gobos,

1 instlalled, and 6 seperate. This unit includes a hanging bracket and

may be hung or set on a flat surface. For best results, use a fog or

haze machine to enhance the beam output. Please read the following

instructions before installing or operating your new Image 250.™

Operating Instructions: Plug the unit in to a matching power outlet

or into a power pack. Light output will be immediate when the unit is

powered on. You can reverse the wheel using the switch in back.You

can also adjust the speed by turning the knob located on the rear of

the unit.

Mounting: When used with included mounting bracket, this unit may

be mounted in any safe position or set on a flat stable surface.

Caution! Be sure not to obstruct cooling vents and keep this unit in a

well ventilated area. Never open the unit while in use. Avoid touching

the lamps, the lamp will get extremely hot under normal usage and

may cause serious injury.

Image 250™ Operation

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future

reference.

Image 250™ General Instructions

Image 250™ Precautions

• Keep the outside of this device dry at all times. Do not spill water

or other liquids into or on to your unit. To prevent re or shock

hazard, do not expose this product to rain or moisture.

• Be sure to save the packing carton in the event you may have to

return the unit for service.

• This unit is designed for interior use only. Do not use this unit out

doors. Use of product outdoors will void the warranty.

• Be sure that the local power outlet match that of the required vol-

tage for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Always route your power cord out of the way of foot trafc.

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in the rare case of an internal short.

• Disconnect the unit’s main power when left unused for long peri-

ods of time.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Never block the ventilation holes.

• Do not attempt to operate this unit, if it becomes damaged in any

way.

• Never operate this unit when it’s cover is removed.

• This unit is for adult use only. Keep out of the reach of children.

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal optical lenses must be carried out periodically to optimize light

output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging your

unit back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.E. smoke, fog residue, dust, dew).

Image 250™ Cleaning

©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 4©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 3

©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 5

Image 250™ Warranty Registration

The Image 250™ carries a 1 year limited warranty. We recommend

you fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight

pre-paid and accompany a return authorization (R.A.) number. If the

unit is under warranty, you must provide a copy of your proof of pur-

chase invoice. Please contact American DJ®customer support for a

R.A. number.

©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 6

Image 250™ Breaker Reset

Image 250™ Lamp Replacement

Lamp Replacement: Caution! Never open the unit while in use.

Always disconnect the main power before attempting to replace the

lamps. Allow the unit ample time to cool before replacing lamps

1. Be sure to follow the proper procedures when handling halogen

bulbs.

2. Locate the lamp cover on the bottom of unit. Remove the two

thumb screw that hold lamp cover in place.

3. Remove the lamp cover to expose the lamp/socket assembly.

4. Gently remove and discard the bad lamp.

5. Insert the new lamp in the lamp/socket assembly.

6. Reassemble in reverse order.

Remember to always replace with the exact same type lamp and

fuse, unless otherwise specified by an authorized American DJ®

service technician.

Breaker Reset: This unit is equipped with a safety breaker. This

breaker is designed to close the power circuit in the event of an inter-

nal short, reducing the risk of electric shock and fire. To reset the

breaker, push the breaker button in until you hear it pop back in to

place. If the breaker continues to pop, stop using the unit and con-

tact customer support the unit may require service.

This unit comes with a 53.5mm interchangable gobo. 6 dfferent

gobos are also included. Changing the gobo is a easy proce-

dure. Follow the instructions below.

Caution! Never open the unit when in use. Always disconnect

the main power before attempting to change the gobo.

Caution! Make sure you have given the unit enough time to cool

off, before doing this!

1. Unscrew the thumb screw located at the bottom rear of

the unit in front of the lamp comver. Slide the gobo holder

out of the unit.

2. Using a phillips screwdriver loosen the two top screws and

remove the bottom middle screw. You can now slide the

gobo out and slide another gobo into its place.

3. Change the gobo, and reassemble the unit.

Image 250™ Changing the Gobo

Image 250™ Halogen Lamp Warning

This fixture is fitted with halogen lamps which are highly suscep-

tible to damage if improperly handled. Never touch lamp with your

bare fingers as the oil from your hands will shorten lamp life. Also,

never move the fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty conditions.

©American DJ Supply

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

Technical Specifications:

Model: Image 250™

Lamp: ZB-ELC10 120v/250w

Voltage*: 110v~120v / 60Hz or

Dimensions: 12.5”(L)x8.75”(W)x8.25”(H)

Gobos: 7

Gobo Size: 53.5

Viewable Gobo Size: 28mm

Weight: 7.5 Lbs./3.4 Kgs

Breaker: 5 Amp

Lenses: 20

Fan Cooled Yes

Working Position: Any Safe position

* Operating voltage is preset at the factory.

Please Note: Specications and improvements in the design of

this unit and this manual are subject to change without any prior

written notice.

©American DJ Supply®- www.americandj.com - Image 250™ Instruction Manual Page 7

1 YEAR LIMITED WARRANTY

A. American DJ®hereby warrants, to the original purchaser, American DJ®products to be

free of manufacturing defects in material and workmanship for a period of 90 days from the

date of purchase. This warranty shall be valid only if the product is purchased within the

United States of America, including possessions and territories. It is the owner’s respon-

sibility to establish the date and place of purchase by acceptable evidence, at the time

service is sought.

B. For warranty service, send the product only to the American DJ®factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ®will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ®shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ®concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than

the American DJ®factory unless prior written authorization was issued to purchaser by

American DJ®; if the product is damaged because not properly maintained as set forth in

the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ®will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this war-

ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ®in connection with this product, includ-

ing warranties of merchantability or tness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of

merchantability or tness, shall apply to this product after said period has expired. The

consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ®be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ®Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this warranty

Image 250™ Warranty

Dieses Handbuch passt für folgende Modelle

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Mega Panel LED Bedienungsanleitung

American DJ

American DJ X-Color LED Plus Bedienungsanleitung

American DJ

American DJ Saturn Tri LED Bedienungsanleitung

American DJ

American DJ BU-350 Bedienungsanleitung

American DJ

American DJ RollerTron Bedienungsanleitung

American DJ

American DJ Color Shot Bedienungsanleitung

American DJ

American DJ Fire Bowl Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 EX Bedienungsanleitung

American DJ

American DJ Wave Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ Rover LED Bedienungsanleitung

American DJ

American DJ Galaxian Royale Bedienungsanleitung

American DJ

American DJ Tempest 575H Bedienungsanleitung

American DJ

American DJ X-Scan LED Plus Bedienungsanleitung

American DJ

American DJ Accu Spot Pro Bedienungsanleitung

American DJ

American DJ User Instructions Bedienungsanleitung

American DJ

American DJ WLED CURTAIN Bedienungsanleitung

American DJ

American DJ LED Trispot Bedienungsanleitung

American DJ

American DJ Flash Duo Bedienungsanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ Razz Mataz Bedienungsanleitung

American DJ

American DJ Micro Image RGB Bedienungsanleitung

American DJ

American DJ Accu Spot 250 II Bedienungsanleitung

American DJ

American DJ Aquarius II Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung