American DJ SWEEPER BEAM LED Bedienungsanleitung

3/13

User Instructions

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 2

Sweeper Beam LED General Information

Unpacking: Thank you for purchasing the Sweeper Beam LED by

ADJ Products, LLC. Every Sweeper Beam LED has been thoroughly

tested and has been shipped in perfect operating condition. Carefully

check the shipping carton for damage that may have occurred during

shipping. If the carton appears to be damaged, carefully inspect your

xture for any damage and be sure all equipment necessary to oper-

ate the unit has arrived intact. In the event damage has been found

or parts are missing, please contact our toll free customer support

number for further instructions. Please do not return this unit to your

dealer without contacting customer support rst.

Introduction: The Sweeper Beam LED is an intelligent, 8-zone LED,

beam effect. The Sweeper Beam LED can operate as a stand alone

fixture or in a Master/Slave configuration. The Sweeper Beam LED has

three operating modes; sound active mode, show mode, and DMX

control. This fixture is suitable for theaters, studios, retail stores, and

other similar locations. This fixture is suitable for theaters, studios,

retail stores, and other similar locations. For best results use fog or

special effects smoke to enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 22 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Sweeper Beam LED Safety Precautions

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 4ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 3

• DMX-512 Protocol

• 4 DMX Channel Modes (1 Channel Mode, 6 Channel Mode, 11

Channel Mode, & 15 Channel Mode)

• 3 Operating Modes - Sound Active, Show Mode, and DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

Sweeper Beam LED Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact ADJ Products, LLC.

ADJ Products, LLC will not accept any liability for any resulting dam-

ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

Sweeper Beam LED Handling Precautions

Sweeper Beam LED Warranty Registration

The Sweeper Beam LED carries a 3 year (1095 days) limited war-

ranty. Please fill out the enclosed warranty card to validate your

purchase and warranty. You may also register your product online at

www.adj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact ADJ Products, LLC

customer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Sweeper Beam LED General Instructions

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 6ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 5

Power Supply: The ADJ Sweeper Beam LED contains a automatic

voltage switch, which will auto sense the voltage when it is plugged

into the power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Sweeper Beam LED can be controlled via DMX-512

protocol. The Sweeper Beam LED can be a 1, 6, 11 or 15 channel DMX

unit. The DMX address is set electronically using

the controls on the rear panel of the unit. Your

unit and your DMX controller require a approved

DMX-512 110 Ohm Data cable for data input and

data output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables, be

sure to use standard 110-120 Ohm shielded cable

(This cable may be purchased at almost all pro-

fessional sound and lighting stores). Your cables

should be made with a male and female XLR connector on either end

Sweeper Beam LED Set Up

Figure 1

Sweeper Beam LED Hanging Precautions

Fixture installation must always be secured with a secondary

safety attachment, such as an appropriate safety cable.

Regardless of the rigging option you choose for your Sweeper

Beam LED always be sure to secure your xture with a safety

cable (not included).

Caution: For added protection mount the xtures in areas out-

side of walking paths, seating areas, or areas were the xture

might be reached by unauthorized personal.

Before mounting the xture to any surface, make sure that the

installation area can hold a minimum point load of 10 times the

device’s weight.

To avoid injury, never stand directly below the device when

mounting, removing, or servicing the xture.

Always use and install a safety cable ( not included) as a safety

measure to prevent accidental damage and/or injury in the

event the clamp fails.

Be sure to complete all rigging and installation procedures

before connecting the main power cord to the appropriate wall

outlet.

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 7 ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Sweeper Beam LED Set Up

of the cable. Also remember that DMX cable must be daisy chained

and cannot be split.

Sweeper Beam LED Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

Sweeper Beam LED Installation

The unit should be mounted using a mounting clamp (not provided),

afxing it to the mounting bracket that is provided with the unit.

Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10

times the unit’s weight. Also, always use a safety cable that can hold

12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 10ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 9

Sweeper Beam LED System Menu

System Menu: When making adjustments press ENTER

to conrm your setup and then press and hold the MENU

button for at least 3 seconds. To exit without making any

adjustments press the MENU button.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until

“ADDR” is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER and then press and hold the MENU button to set

your desired DMX address.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is

displayed, press ENTER and then press and hold the MENU

button to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures

will now have contrast movement to each other.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed,

press ENTER. Either “1CH”, “6CH”, “11CH”, or “15CH” will be

displayed

2. Press the UP or DOWN buttons to choose your desired DMX

mode and press ENTER to conm and exit.

Sweeper Beam LED System Menu

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 11 ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 12

SENS - Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. The display will show a number between 0-100. Press the UP or

DOWN buttons to adjust the sound sensitivity. 0 being the least sen-

sitive and 100 the most sensitive.

3. Press the ENTER button to conrm.

DNST - This mode can be used as a precaution mode, that

in case the DMX signal is lost, the operating mode chosen in

the setup is the running mode the xture will go into when

the DMX signal is lost. You can also set this as the operat-

ing mode you would like the unit to return to when power is

applied.

1. Press the MENU button until “DNST” is displayed, press

ENTER.

2. Either “MAST”, “BLND”, or “LAST” will be displayed. Choose

an operating mode you would like the unit to start up in when

power is applied or the DMX signal is lost.

• MAST (Master Slave) - If the DMX signal is lost or power is

applied, the unit will automatically go into Master Slave mode.

• BLND (Blackout) - If the DMX signal is lost or power is applied,

the unit will automatically go into stand by mode.

• LAST (Last State) - If the DMX signal is lost the xture will stay

in the last DMX set up. If power is applied and this mode is set,

the unit will automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press

Sweeper Beam LED System Menu

SET - This will set the Sweeper to a preset angle.

1. Press the either the MENU button until “SET” is displayed,

press ENTER. Either “150”, “120”, or “90” will be displayed,

these are the preset angles.

2. Press the UP or DOWN buttons to choose your desired angle

and press ENTER to conm and exit.

SHND: SH 0-SH16 - Show modes 0-16 (Factory

programs). Show mode can run with or without sound active

mode.

1. Press the MENU button until “SHND” is displayed, press

ENTER.

2. “Sh X” will now be displayed, “X” representing a number

between 0-16. Programs 1-16 are factory programs, while “Sh

0” is random mode. Press the UP or DOWN buttons to nd your

desired show.

3. When you have found your desired show press ENTER, then

press and hold the MENU button for at least 3 seconds to acti-

vate.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode,

or “OFF” to deactivate sound active mode.

3. Press ENTER, and then press and hold the MENU button for

at least 3 seconds to activate.

Sweeper Beam LED System Menu

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 13 ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 14

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch off

after 10 seconds. To make the display reappear, press and hold

the MENU button for at least 5 secs.

3. Press ENTER to conrm. To make the display reappear, press

and hold the MENU button for at least 5 secs.

REV - This function is used in conjuction with 11 Chan-

nel mode and 15 Channel mode. The direction in which the

projector lenses light up can be reversed so that the LED

line up can start at either end of the bar. This feature is

useful when the unit is installed in a reversed orientation so

the unit itself does not have to be uninstalled and reversed.

Example: When using 11 Channel mode, Channel 4 (LED 1) can

start at either end of the bar depending on this functions set up.

1. Press the MENU button until “REV” is displayed, press

ENTER.

2. The display will show either “YES” or “NO”. Press the UP or

DOWN buttons to select “YES” which will have the projector

lenses light up right to left, or “NO” which will have the projec-

tor lenses light up left to right.

3. Press ENTER to conrm.

TILT - This function activates tilt inversion.

1. Press the MENU button until “TILT” is displayed, press

ENTER.

2. The display will show either “YES” or “NO”. Press the UP

or DOWN buttons to select “YES” to activate tilt inversion, or

Sweeper Beam LED System Menu Sweeper Beam LED System Menu

“NO” to deactivate tilt inversion.

3. Press ENTER, and then press and hold the MENU button for

at least 3 seconds to activate.

DISP - This will “ip” the LED display 180º.

1. Press the MENU button until “DISP” is displayed, press

ENTER.

2. Either “DISP” or “DSIP” will now be displayed. Press the

ENTER button to “ip” the display.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press

ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running

time of the xture.

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - With this function you can display the version soft-

ware of the xture.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The software version will now be displayed. Press MENU to

exit.

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 16ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 15

Sweeper Beam LED Operation

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 6-8 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 10 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons to choose either OFF or ON, and

press ENTER, then press and hold MENU for 3 seconds to con-

rm. To adjust sound sensitivity see page 12.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: In this mode you can choose 1 of 16 show modes to

run.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,

and press ENTER then press and hold MENU for 3 seconds to

con rm. See page 11 for more info.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 9 xtures maximum. After 9 xtures you will need

to use a new power outlet. They must be the same xtures. DO

NOT mix xtures.

Sweeper Beam LED Power Cord Daisy Chain

Operating Modes: The Sweeper Beam LED can operate in

three different modes. In each mode you can run the fixture as a

stand alone fixture or in a master/slave confiugration. This next

section will detail the differences in the operating modes.

•Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

•Show mode -

Choose 1 of 16 show modes to run.

•DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation®Show

Designer.™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. Set the Master unit to your desired operating mode.

3. For the slave units press the MENU button until “SLND” is dis-

played, and Press ENTER. Set the slave units to either “SL 1” or

“SL 2”.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The Sweeper Beam LED can be a 1, 6, 11, or 15 DMX channel

fixture. See pages 17-21 for detailed description of the DMX val-

ues and traits.

Sweeper Beam LED Operation

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 17 ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 18

Sweeper Beam LED 1 DMX Channel Mode

Channel Value Function

1 SHOWS

0 - 7 BLACKOUT

8 - 22 SHOW 1

23 - 37 SHOW 2

38 - 52 SHOW 3

53 - 67 SHOW 4

68 - 82 SHOW 5

83 - 97 SHOW 6

98 - 112 SHOW 7

113 - 127 SHOW 8

128 - 142 SHOW 9

143 - 157 SHOW 10

158 - 172 SHOW 11

173 - 187 SHOW 12

188 - 202 SHOW 13

203 - 217 SHOW 14

218 - 232 SHOW 15

233 - 247 SHOW 16

248 - 255 RANDOM SHOW

Sweeper Beam LED UC3 Control

Blackout Blackout the unit

Function 1. Sound Strobe (Full on).

2. Auto Strobe (Full on). Select Shows (Show 1-16).

Mode Random Show(LED OFF) Show(LED ON)

Sweeper Beam LED 6 DMX Channel Mode

Channel Value Function

1 0 - 255 TILT -30° -210°

2 TILT MOVEMENT MACRO

0 - 7 NO FUNCTION

8 - 43 TILT MOVEMENT MACRO 60° -120°

44 - 79 TILT MOVEMENT MACRO 45° -135°

80 - 115 TILT MOVEMENT MACRO 30° -150°

116 - 151 TILT MOVEMENT MACRO 0° -180°

152 - 187 TILT MOVEMENT MACRO -30° -210°

188 - 223 TILT MOVEMENT MACRO 0° -90°

224 - 255 TILT MOVEMENT MACRO 90° -180°

3 TILT MOVEMENT MACRO SPEED

0 - 7 NO FUNCTION

8 - 255 SLOW - FAST

4 CHASES

0 - 7 NO FUNCTION

8 - 22 CHASE 1

23 - 37 CHASE 2

38 - 52 CHASE 3

53 - 67 CHASE 4

68 - 82 CHASE 5

83 - 97 CHASE 6

98 - 112 CHASE 7

113 - 127 CHASE 8

128 - 142 CHASE 9

143 - 157 CHASE 10

158 - 172 CHASE 11

173 - 187 CHASE 12

188 - 202 CHASE 13

203 - 217 CHASE 14

218 - 232 CHASE 15

233 - 247 CHASE 16

248 - 255 FULL ON

5 0 - 255 CHASE SPEED SLOW - FAST

6 0 - 255 MASTER DIMMER 0% - 100%

ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 19 ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 20

Sweeper Beam LED 15 DMX Channel Mode

Channel Value Function

1 0 - 255 TILT -30° -210°

2 TILT MOVEMENT MACRO

0 - 7 NO FUNCTION

8 - 43 TILT MOVEMENT MACRO 60° -120°

44 - 79 TILT MOVEMENT MACRO 45° -135°

80 - 115 TILT MOVEMENT MACRO 30° -150°

116 - 151 TILT MOVEMENT MACRO 0° -180°

152 - 187 TILT MOVEMENT MACRO -30° -210°

188 - 223 TILT MOVEMENT MACRO 0° -90°

224 - 255 TILT MOVEMENT MACRO 90° -180°

3 TILT MOVEMENT MACRO SPEED

0 - 7 NO FUNCTION

8 - 255 SLOW - FAST

4 CHASES

0 - 7 NO FUNCTION

8 - 22 CHASE 1

23 - 37 CHASE 2

38 - 52 CHASE 3

53 - 67 CHASE 4

68 - 82 CHASE 5

83 - 97 CHASE 6

98 - 112 CHASE 7

113 - 127 CHASE 8

128 - 142 CHASE 9

143 - 157 CHASE 10

158 - 172 CHASE 11

173 - 187 CHASE 12

188 - 202 CHASE 13

203 - 217 CHASE 14

218 - 232 CHASE 15

233 - 247 CHASE 16

248 - 255 FULL ON

5 0 - 255 CHASE SPEED SLOW - FAST

6 0 - 255 MASTER DIMMER 0% - 100%

Sweeper Beam LED 11 DMX Channel Mode

Channel Value Function

1 0 - 255 TILT -30° -210°

2 0 - 255 MASTER DIMMER 0% - 100%

3 STROBING

0 - 15 NO FUNCTION

16 - 131 STROBING SLOW - FAST

132 - 139 NO FUNCTION

140 - 181 SLOW OPEN - FAST CLOSE

182 - 189 NO FUNCTION

190 - 231 SLOW CLOSE - FAST OPEN

232 - 239 NO FUNCTION

240 - 247 RANDOM STROBING

248 - 255 NO FUNCTION

4 0 - 255 DIMMING 0% - 100% (LENS 1)

5 0 - 255 DIMMING 0% - 100% (LENS 2)

6 0 - 255 DIMMING 0% - 100% (LENS 3)

7 0 - 255 DIMMING 0% - 100% (LENS 4)

8 0 - 255 DIMMING 0% - 100% (LENS 5)

9 0 - 255 DIMMING 0% - 100% (LENS 6)

10 0 - 255 DIMMING 0% - 100% (LENS 7)

11 0 - 255 DIMMING 0% - 100% (LENS 8)

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Saga Bedienungsanleitung

American DJ

American DJ X-Color LED Plus Bedienungsanleitung

American DJ

American DJ Revo XPress Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ Fan-1000 Bedienungsanleitung

American DJ

American DJ Micro Phase Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ Nucleus PRO Bedienungsanleitung

American DJ

American DJ LTS-50T Bedienungsanleitung

American DJ

American DJ Reflex Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ SS-DMX19CTM Bedienungsanleitung

American DJ

American DJ S-10S Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Inno Color Beam Z7 Bedienungsanleitung

American DJ

American DJ Verti-Pro II Bedienungsanleitung

American DJ

American DJ Stingray Bedienungsanleitung

American DJ

American DJ Flash-1C Bedienungsanleitung

American DJ

American DJ Razz Mataz Bedienungsanleitung

American DJ

American DJ Mini Mace Bedienungsanleitung

American DJ

American DJ LED Touch Bedienungsanleitung

American DJ

American DJ Space Balls Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ Royal Sky Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung