Amprobe LAN-1 Bedienungsanleitung

LAN-1

Lan Cable Tester

Users Manual

Mode d’emploi•

Bedienungshandbuch•

Manuale d’Uso•

Manual de uso•

Användarhandbok•

English

LAN-1

Lan Cable Tester

Users Manual

LAN1_Rev001

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for

1 year from the date of purchase. This warranty does not cover fuses, disposable

batteries or damage from accident, neglect, misuse, alteration, contamination,

or abnormal conditions of operation or handling. Resellers are not authorized

to extend any other warranty on Amprobe’s behalf. To obtain service during the

warranty period, return the product with proof of purchase to an authorized

Amprobe Test Tools Service Center or to an Amprobe dealer or distributor. See

Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER

WARRANTIES - WHETHER EXPRESS, IMPLIED OR STAUTORY - INCLUDING IMPLIED

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY,

ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not

allow the exclusion or limitation of an implied warranty or of incidental or

consequential damages, this limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or for calibration

should be accompanied by the following: your name, company’s name, address,

telephone number, and proof of purchase. Additionally, please include a brief

description of the problem or the service requested and include the test leads

with the meter. Non-warranty repair or replacement charges should be remitted

in the form of a check, a money order, credit card with expiration date, or a

purchase order made payable to Amprobe® Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting

repair. During the warranty period any defective test tool can be returned to your

Amprobe® Test Tools distributor for an exchange for the same or like product.

Please check the “Where to Buy” section on www.amprobe.com for a list of

distributors near you. Additionally, in the United States and Canada In-Warranty

repair and replacement units can also be sent to a Amprobe® Test Tools Service

Center (see address below).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be sent to a

Amprobe® Test Tools Service Center. Call Amprobe® Test Tools or inquire at your

point of purchase for current repair and replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe® Test Tools

distributor for a nominal charge. Please check the “Where to Buy” section on

www.amprobe.com for a list of distributors near you.

European Correspondence Address*

Amprobe®Test Tools Europe

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

*(Correspondence only – no repair or replacement available from this address.

European customers please contact your distributor.)

➊RJ45 jack for sourcing end

(OUT).

➋RJ45 jack for receiving end (IN).

➌

LED indicators for sourcing end

(OUT) Green.

➍LED indicators for receiving end

(IN). Red.

➎AUTO scan button.

➏TEST button for MANUal test.

➐POWER ON/OFF button.

➑BATTery TEST button.

➒HOLD button.

➓MANUal scan button.

Low BATTery indicator.

Remote Terminator LED

indicator for ground wire

Remote Terminator LED

indicators for data lines

Remote Terminator RJ45 jack

HOLD

MAN

AUTO

TEST

BATT

REMOTE

TERMINATOR

IN OUT

1 2 3 4 5 6 7 8 G

OUT

GRD

LAN-1

Lan cable tester

CONTENTS

Symbols..................................................................................................................5

Unpacking and Inspection....................................................................................5

Introduction...........................................................................................................5

Operation ..............................................................................................................6

Loopback Test (cable with both ends in one location)..................................6

Remote Test (cable with both ends at different locations)...........................6

Hold ..................................................................................................................6

Test Examples ........................................................................................................7

Speciﬁcations.........................................................................................................7

Maintenance and Repair .....................................................................................8

Battery Replacement ............................................................................................8

SYMBOLS

Refer to the manual Do not dispose of this

product as unsorted

municipal waste.

Conforms to relevant

Australian standards. Complies with EU

directives



This equipment not

for connection to

public communications

networks, such as active

telephone systems.

Warning and Precautions

DO NOT use on live circuits. These voltage levels pose a potential shock•

hazard to the user.

To avoid electrical shock hazard, observe the proper safety precautions•

when working with voltages above 60 VDC or 30 VAC rms.

Never ground yourself when taking measurements.•

Do not operate the instrument in an explosive atmosphere.•

To reduce the risk of ﬁre or electric shock, do not expose this product to•

rain or moisture.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 LAN-1 Cable tester

1 Remote Terminator

1 9 volt battery

1 RJ45 to female BNC cable

1 RJ45 to male BNC cable

1 RJ45 to RJ45 cable

1 female BNC to female BNC connector

1 Users Manual

If any of the items are damaged or missing, return the complete package to

the place of purchase for an exchange.

INTRODUCTION

The LAN-1 Cable Tester is designed for testing opens, shorts and miswired

cable installations .

Testing capabilities are:

Test pin conﬁguration for 10/100 base -T cable, 10 base-2 cable, RJ45•

modular cables, AT&T 258A cable, EIA / TIA 568A/568B cables and Token

Ring Cable etc.

Verify cable continuity, open, short or incorrectly wired.•

Test installed cable on wall plate or the patch panels by using the Remote•

Termination module.

Buzzer sound warning for error condition.•

OPERATION

Press1. button for power ON. If no cable is attached or cable is defective,

the buzzer will sound.

Press BATT to verify proper operating voltage. The BATT LED will not light2.

and LAN-1 will not operate correctly if battery is below 7 volts.

Green LEDs are the source indicators. Red LED’s are the test indicators.3.

Red LED’s ON indicate cable line continuity. Red LED’s OFF indicate open

cable lines.

Loopback Test (cable with both ends in one location)

Connect cable with RJ-45 terminations on both ends to IN and OUT test1.

sockets.

Press2. button for power ON. Press AUTO (default) or MAN button to

start scanning.

AUTO scanning will step through lines 1 to 8 and ground (if connected)3.

and repeats until stopped.

MAN scanning will go into manual mode and TEST will step through the4.

different lines.

Remote Test (cable with both ends at different locations)

Connect one cable end to OUT connector.1.

Connect REMOTE TERMINATOR to the other end of cable under test.2.

Press3. button for power ON. Press AUTO (default) or MAN button to

start scanning.

AUTO scanning will step through lines 1 to 8 and ground (if connected)4.

and repeat until stopped.

MAN scanning go into manual mode and TEST will step through the5.

different lines.

Line test results (Red LED’s) are shown on the Remote Terminator.6.

Hold

The HOLD button saves the displayed error condition and stops testing. Press

the HOLD button to return to normal operation.

TEST EXAMPLES

Continuity Green onooooooo

Pin 2 has continuity 1 2 3 4 5 6 7 8 G

Red onooooooo

Open Green onooooooo

Pin 2 is open 1 2 3 4 5 6 7 8 G

Red ooooooooo

Short Green onnoooooo

Pins 2 and 3 are shorted 1 2 3 4 5 6 7 8 G

Red onnoooooo

Miswire Green onooooooo

Pins 2 and 6 are miswired 1 2 3 4 5 6 7 8 G

Red ooooonooo

SPECIFICATIONS

General

Display: Red and Green LED’s

Battery: 9V, 006P or IEC 6F22 or NEDA 1604.

Low Battery Indicator: The LED indicator will not turn ON when

BATT button pushed

Battery Life: Approx 20 hours. (Alkaline battery)

Environment: Indoor operation, maximum altitude

- 2000 m (6561 ft.)

Temperature / Humidity:

Operation: 0 to 40°C (32 to 104°F), 10 to 70% RH.

Storage: -10 to 60°C (14 to 140°F), 10 to 90% RH.

Dimension: 130 x 64 x 38mm (5.1 x 2.2 x 1.5 in)

Weight: 1.26 kg (0.6 lb)

-EMC: EN61326-1 This product complies with requirements of the

following European Community Directives: 89/336/EEC (Electromagnetic

Compatibility) and 73/23/EEC (Low Voltage) as amended by 93/68/EEC (CE

Marking). However, electrical noise or intense electromagnetic ﬁelds in the

vicinity of the equipment may disturb the measurement circuit. Measuring

instruments will also respond to unwanted signals that may be present within

the measurement circuit. Users should exercise care and take appropriate

precautions to avoid misleading results when making measurements in the

presence of electronic interference.

Electrical

Maximum line length: ~300 meters

Connector types: RJ45, BNC

DO NOT use on live circuits.

MAINTENANCE AND REPAIR

If there appears to be a malfunction during the operation of the tester, the

following steps should be performed in order to isolate the cause of the

problem.

Press the BATTery button to check the battery. Replace the battery1.

immediately if the LED indicator will not turn ON.

Review the operating instructions for possible mistakes in operating2.

procedure.

Except for the replacement of the battery, repair of the meter should be

performed only by a Factory Authorized Service Center or by other qualiﬁed

instrument service personnel. The front panel and case can be cleaned with

a mild solution of detergent and water. Apply sparingly with a soft cloth and

allow to dry completely before using. Do not use aromatic hydrocarbons or

chlorinated solvents for cleaning.

BATTERY REPLACEMENT

1. Turn off the meter and slide out the battery cover. Replace the battery with

a NEDA type 1604 or equivalent 9V alkaline battery. Replace the cover.

2. Remove battery when the LAN-1 is not used for extended period.

OPEN

Battery Replacement

LAN1_Rev001

LAN-1

Testeur de câbles LAN

Mode d’emploi

Français

Andere Handbücher für LAN-1

Inhaltsverzeichnis

Sprachen:

Andere Amprobe Prüfgeräte Handbücher

Amprobe

Amprobe UAT-600-EUR Series Bedienungsanleitung

Amprobe

Amprobe UAT-505 Bedienungsanleitung

Amprobe

Amprobe CT238A Bedienungsanleitung

Amprobe

Amprobe LT-10-EUR Bedienungsanleitung

Amprobe

Amprobe AMB-55 Bedienungsanleitung

Amprobe

Amprobe BAT-250 Bedienungsanleitung

Amprobe

Amprobe MEGATEST 5000 Bedienungsanleitung

Amprobe

Amprobe Telaris Series Bedienungsanleitung

Amprobe

Amprobe INSP-3 Bedienungsanleitung

Amprobe

Amprobe ROBIN KMP7010 Bedienungsanleitung

Amprobe

Amprobe PRM-6 Bedienungsanleitung

Amprobe

Amprobe ST-101B Originalbetriebsanleitung

Amprobe

Amprobe AMB-110 Bedienungsanleitung

Amprobe

Amprobe AMB-25 Bedienungsanleitung

Amprobe

Amprobe AMB-45 Bedienungsanleitung

Amprobe

Amprobe A-5000 Bedienungsanleitung

Amprobe

Amprobe PRM-2 Bedienungsanleitung

Amprobe

Amprobe BT-120 Bedienungsanleitung

Amprobe

Amprobe BAT-200 Bedienungsanleitung

Amprobe

Amprobe VPC-30 Bedienungsanleitung

Amprobe

Amprobe gp-2a Bedienungsanleitung

Amprobe

Amprobe VPC-10 Bedienungsanleitung

Amprobe

Amprobe AMB-50 Bedienungsanleitung

Amprobe

Amprobe AT-2004-A Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung