AMS GP30-DEV-KIT Bedienungsanleitung
User Guide
UG000292
TDC-GP30
Reference Board
GP30-DEV-KIT
v1-00 •2019-Feb-26
Document Feedback
TDC-GP30
Content Guide
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │2
Content Guide
1Introduction....................................3
1.1 Kit Content.................................................... 3
1.2 Ordering Information .................................... 4
2Quick Start Guide ..........................5
2.1 Install the Software....................................... 5
2.2 Install the Hardware ..................................... 5
2.3 Quick Start for Initial Measurements............ 5
3Hardware Description....................8
3.1 Introduction................................................... 8
3.2 Communication Interface............................. 8
4Software Description...................10
4.1 Measurement .............................................10
4.2 Ultrasonic Measurement Control ...............13
4.3 Temperature Measurement Control........... 14
4.4 General Control.......................................... 15
4.5 Interfaces....................................................16
4.6 Interrupt & Error Handling..........................17
4.7 ams............................................................. 18
4.8 Firmware Parameters and Firmware Error
Counters..................................................... 18
5Software Menu............................. 20
5.1 File.............................................................. 20
5.2 Tools .......................................................... 20
5.3 Firmware.................................................... 22
5.4 Help............................................................ 27
6Schematics, Layers and BOM .... 29
7Reference Modules and
Transducers................................. 32
7.1 Modules...................................................... 32
7.2 Transducers............................................... 36
8Revision Information................... 39
9Legal Information ........................ 40
Document Feedback
TDC-GP30
Introduction
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │3
1 Introduction
The GP30-DEV-KIT is a platform for a quick and easy start-up and evaluation of the TDC-GP30
ultrasonic flow converter (UFC). It supports the QFN32 package, which offers the functionality need for
standard water and heat meters. The development kit offers user-friendly configuration and extensive
testing of the TDC-GP30, but also the complete assembler environment for programming the device.
For a proper use of the evaluation system, we strongly recommend to refer to the latest TDC-GP30
datasheets.
1.1 Kit Content
Figure 1:
Kit Content
1 PICOPROG V3.0 (Programmer and interface)
2 USB cable (Connects PICOPROG V3.0 to PC)
3 GP30-DEMO MODULE (Based on TDC-GP30 in QFN32 package)
Please download the latest software for the kit from
https://download.ams.com/SPECIALTY-SENSORS/TDC-GP30
1
2
3
Document Feedback
TDC-GP30
Introduction
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │4
1.2 Ordering Information
Ordering Code
Part Number
Description
GP30-DEV-KIT
220260003
TDC-GP30 Demo Kit for QFN32 version
including PICOPROG and cables
GP30-DEMO-KIT-F01
220260006
TDC-GP30 Demo Kit with firmware for QFN32
version including PICOPROG and cables
GP30-DEMO MODULE
220260002
GP30 demo board for QFN32 version
GP30-DEMO-US-F01
220260005
GP30 demo board with firmware for QFN32
version
Document Feedback
TDC-GP30
Quick Start Guide
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │5
2 Quick Start Guide
This section describes how to quickly set up the GP30-DEV-KIT, establish basic operation and make
measurements.
2.1 Install the Software
It is crucial to install the software before connecting the evaluation kit to your computer. A default
driver loading of your OS may interfere with correct installation.
●Download the latest zipped software installation package to the desired directory.
●Unzip the package to the desired directory.
●Open “setup.exe” from the unzipped directory.
●Follow the instructions on the screen.
2.2 Install the Hardware
●Make sure software is installed correctly before proceeding with this step!
●Connect your computer with the PICOPROG V3.0 using USB cable.
●Connect PICOPROG V3.0 and the evaluation kit motherboard using the DB15 interfaces
●The green LED on the evaluation kit should be on.
●Connect your spool piece to US_UP and US_DOWN
2.3 Quick Start for Initial Measurements
From the “Start” menu, go to “All Programs” and then to the “ams” directory. Double click the
“GP30_v1_7_0” icon (or newer versions, if available) to begin execution of the evaluation software.
The following screen should appear:
Document Feedback
TDC-GP30
Quick Start Guide
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │6
Figure 2:
Measurement Page
●Click the “Verify Interface” button to confirm communication between PICOPROG V3.0 and
TDC-GP30 is working. Both fields, “Pico Prog FW version”and “Comm. With GP30 OK?”,
should become green.
●Next, open our configuration GP30Y_config_default_A1.A2.11.03 and download it into the chip,
pressing “Write Config”.
●Connect your spool piece to pins US_UP and US_DOWN.
●Press “Start Measurement” to begin measuring.
At this point, after successful completion of the above steps, a basic operation of the EVA kit should
be possible. The following sections provide a detailed description of the hardware and software for
advanced operation.
Document Feedback
TDC-GP30
Quick Start Guide
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │7
Figure 3:
PICOPROG Registry
If PICOPROG is not displayed correctly then go to the drivers folder, e.g. C:\Program Files
(x86)\ams\GP30\data\ and install the driver for your operating system manually. In case of an upgrade
of the software to a newer version, please make sure that the software uses the latest driver. For
manual installation open the USB communications window and check the firmware version of the
PICOPROG. It should be version PICOPROG_GP30_v21.hex or higher:
Figure 4:
PICOPROG Manual Installation
Document Feedback
TDC-GP30
Hardware Description
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │8
3 Hardware Description
3.1 Introduction
The GP30-DEMO MODULE board, shown in Figure 5, is a front-end for a water or heat meters. The
transducers and temperature sensors are directly connected to this board. It comes with a 32.768 kHz
quartz (X2) and a 4 MHz ceramic oscillator (X1). All ports of TDC-GP30 are available. Additional patch
fields allow an easy extension with additional circuits. Those can be amplifiers or analog switches for
operation in gas meter mode.
Figure 5:
GP30-DEMO MODULE
3.2 Communication Interface
The PICOPROG device is a USB-to-SPI converter box that interfaces all UFC evaluation systems.
With version 3.0, the PICOPROG also supports the USB-to-UART conversion of TDC-GP30. The
PICOPROG is registered by the operating system initially as “PICOPROG v3.0 unprogrammed”. As
Piezo
D U
PT1000
C H
GND VCC
INIT
MISO
SCK
MOSI
SSN
-
VCC_LEVEL
Pulse
Interface
Document Feedback
TDC-GP30
Hardware Description
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │9
soon as the GP30 evaluation software starts, a special firmware is written into the PICOPROG to
handle the SPI or UART communication with the TDC-GP30. The PICOPROG is now listed as
“UNIPRO” in the device manager. For SPI communication only, PICOPROG version 2.0 is sufficient.
Figure 6 shows the connection between the PICOPROG and the GP30 board. The flat connector
includes the power lines and the SPI or UART communication lines. On the demo board the
communication interface is initially selected to SPI (by solder bridge LJ2).
VCC_LEVEL is the voltage feedback for the PICOPROG level shifters.
Figure 6:
SUBD15-Connector
Document Feedback
TDC-GP30
Software Description
Demo Kit Manual •PUBLIC
UG000292 •v1-00 • 2019-Feb-26
40 │10
4 Software Description
4.1 Measurement
When started, the software comes up with the main window, showing the “Measurements” tab.
Figure 7:
Main Window
4.1.1 First Step with Measurement Control Elements
A good first step is to load a working configuration and make measurements in frontend mode (without
using the internal 32-Bit µP). ams provides a sample configuration file named
GP30Y_config_default_A1.A2.11.03 which typically works well with DN20 spool pieces.
Load Configuration File: File menu Open Config choose appropriate configuration file
Inhaltsverzeichnis
Andere AMS Hauptplatine Handbücher
AMS
AMS JetCis 130 Bedienungsanleitung
AMS
AMS AS3460 Bedienungsanleitung
AMS
AMS TMD2620-DB Bedienungsanleitung
AMS
AMS CCS811 Bedienungsanleitung
AMS
AMS AS3935 Bedienungsanleitung
AMS
AMS AN5000 Series Montage- und Bedienungsanleitung
AMS
AMS TMF882X-SHIELD Bedienungsanleitung
AMS
AMS AS5000 Bedienungsanleitung
AMS
AMS TSL2584TSV Bedienungsanleitung
AMS
AMS TSL2541 Bedienungsanleitung
AMS
AMS AS3460 Bedienungsanleitung
AMS
AMS Radon AS3993 Montage- und Bedienungsanleitung
AMS
AMS AS3956 Bedienungsanleitung
AMS
AMS TCS3414 EVM2 Bedienungsanleitung
AMS
AMS AS5047P-TS_EK_AB Bedienungsanleitung
AMS
AMS AS5600 Bedienungsanleitung
AMS
AMS TCS3720 Bedienungsanleitung
AMS
AMS AS5601-SO_EK_ST Bedienungsanleitung
AMS
AMS AS5600 Bedienungsanleitung
AMS
AMS AS6204 Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
