AMS AN5000 Series Montage- und Bedienungsanleitung

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

1General Overview

This operational manual describes the function of the AS5000 Programmer in combination with the programming

boards. This tool can program the ams AS5000 series magnetic rotary encoders. The graphical user interface (GUI)

runs on PC running Windows XP or later and controls the programmer via the USB interface.

All major access modes to the OTP memories can be established. Be aware that ams provides the AS5000

Programmer as a reference for programming and reading of mentioned devices (refer to

Appendix A) under laboratory conditions (no warranty for mass production).

Note: Since firmware version v2.10 the AS5000-Programmer contains a boot loader, which provides an update function

for new software release. Please refer to the corresponding application note AN5000-60 (available on our

webpage).

2Hardware Components

2.1 Description of the Hardware Components

Figure 1: Three components of the Pr ogrammer solution

Figure 1 shows the three components which are needed to program the ams magnetic position sensor. Take care that

the connector between programmer and programming board is plugged in the right way.

Warning:

In case of wrong connection, the components in the AS5000 programmer or the encoder can be destroyed!

USB cable

AS5000 programmer

Programming board

(AS5xxx-PB)

LCD display (programmer v1.3 or older only)

Application Note –AS5000 Programmer

www.ams.com

Revision 1.11/ 02/18/2014

Programmer’s right side

Figure 2: AS5000 Programmer M RE connector (right side view)

Pin #

Signal

Comment

Vzap

Programming voltage

Vzap

Programming voltage

D10

Encoder signal

ADC2

Device autodetection voltage

Encoder signal

ADC1

Vzap feedback

Encoder signal

D11

Encoder signal

VDD

Encoder power supply

VDD

Encoder power supply

GND

Ground

GND

Ground

Encoder signal

Encoder & LCD display signal

Encoder signal

LCD signal –Do not use

Encoder & LCD display signal

Application Note –AS5000 Programmer

www.ams.com

Revision 1.11/ 02/18/2014

2.2 Description of the programming board

Figure 3: E xample for an AS5043-PB Programming board

The programming board (AS5xxx-PB) is specific for a group of devices. By jumper setting on this board the build in

firmware in the programming box automatically detects the selected device. It is not recommended to change the

jumper setting to a different encoder type than installed in the socket.

To place or remove a device form the socket, push the black frame of the socket down. This socket has more

connectors as the AS50xx/ AS51xx part and therefore it is important to align the device to the left side of the socket.

The pin 1 of the device must be on the bottom left side. Figure 2 shows the detailed placed device in the socket.

The jumper J9 is specific for the AS5043/AS5143. This Jumper is used to close the feedback loop used for the analog

output operation mode. With this jumper the gain can set to 1.

The jumper J6 is by default closed because the AS5000 Programmer provides 3.3V operation. In case of 5 V operation

the jumper must be removed and the configuration can be changed over the GUI.

ZIF socket

Jumper J9:

Gain = 1

(AS5043 only)

Device Selection

jumper

Jumper J6:

Supply voltage selection

Open: 5V –Close: 3.3V (default)

Connector to the

AS5000 programmer

Location of pin 1 of

the encoder

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

3Installation

3.1 Hardware setup

First connect the AS5xxx-PB to the 20-pin connector of the AS5000 Programmer, as shown on Figure 1.

The AS5000 Programmer is directly powered by the PC via USB. An external power supply is not needed.

3.2 Installing the GUI on the PC

The preliminary software is developed for a Microsoft Windows XP operating system with Service Pack 2. In addition

the dotnet (.NET) framework version 2.0 or more must be installed on the PC. This package can be downloaded free of

charge from the Microsoft webpage:

http://www.microsoft.com/downloads/details.aspx?FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5&displaylang=en

Following Procedure is recommended before starting the GUI:

1. check on your PC if Service Pack 2 is installed

2. install the mentioned .net package to your computer

3. execute AS5000GUI_setup.exe

4. Finally start the GUI using the shortcut in the start menu or desktop.

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

4Graphical User Interface (GUI)

Figure 4: Main window of the GUI, no PB board inserted

Figure 4 shows the main window of the GUI.

In the top left corner, informations about the connected hardware are displayed:

-firmware (FW) type of the connected hardware: ubox (AS5000 Programmer) or dbrd (Demoboard)

-firmware (FW) version

By default the GUI is in the auto detection mode. Any ams device connected on the USB port (one device at the same

time) will be automatically detected and displayed in the right top corner.

Note: The autodetect mode can be disabled and forced to any other device type by selecting the device manually.

Once a PB board inserted, tabs will be displayed allowing go into two main sections: SSI (or TWI) and OTP.

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

4.1 Programming the AS5040/AS5045/AS5140/AS5145/AS5045B

Programming AS5040/AS5140 encoders requires the

AS5040-PB ZIF socket board. This adapter is compatible

with AS5040, AS5140, AS5045,AS5145 and AS5045B.

Jumper J6 must be close for normal operation and

programming operation.

Figure 5: AS5040-PB Programming board

By selecting the SSI tab, information of the angular position and the status bits appear:

Figure 6: SSI tab with AS5040 encoder inserted in AS5040-PB

-Die selection: This option is for dual die AS52xx devices only. For AS50xx and AS51xx devices Die 0 (default)

must be selected.

-Value field is the raw angle extracted from the SSI stream. The angle range is 0 (0°) to 1023 (359.6°)

-Status field displays the status bits extracted from the SSI stream. Green light means that the airgap between

the magnet and encoder is correct. Orange light means the magnet is too close of too far.

-CCW checkbox is the angle direction. To invert the rotating direction, check CCW.

Position of the magnet

Status bits and field alarm

Set the actual angle as

Zero Position

Counter Clockwise mode

Selected die

(dual die AS52xx devices only)

Pin 1

Application Note –AS5000 Programmer

www.ams.com

Revision 1.11/ 02/18/2014

-Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

-Read interval is the SSI stream readout and refresh rate the GUI.

Figure 7: AS5040 SSI tab after Zero P osition programming

This example is the effect when the function Zero Position SET has been performed.

Before programming, the encoder shows the position 651 (Figure 6). One click on Zero Position Set makes the software

writing the value 651 into the OTP Zero Position register (not permanent programming).

Selecting Zero Position Reset will write the value 0 to the OTP Zero Position register.

Note: The Zero Position function is the same for all the AS50xx, AS51xx, AS52xx rotary encoders offering this feature.

Selecting the OTP tab will read the OTP configuration from the IC.

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

Figure 8: OTP tab of an unprogr ammed AS5040

AS5040/AS5045:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is possible

to check the effect of the new configuration.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

AS5140/AS5145:

Load reads the OTP configuration from the permanent fuse register.

Read reads the OTP configuration from the volatile register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is possible

to check the effect.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

4.1 Programming the AS5043

Programming AS5043 encoders requires the AS5043-PB

ZIF socket board.

Jumper J6 must be close for normal operation and

programming operation.

Figure 9: AS5043-PB Programming board

By selecting the SSI tab, information of the angular position and the status bits appear:

Figure 10: SSI tab with AS 5043 inserted in AS5043 -PB

-Die selection: This option is for dual die AS52xx devices only. For AS50xx and AS51xx devices Die 0 (default)

must be selected.

-Value field is the raw angle extracted from the SSI stream. The angle range is 0 (0°) to 1023 (359.6°)

-Status field displays the status bits extracted from the SSI stream. Green light means that the airgap between the

magnet and encoder is correct. Orange light means the magnet is too close of too far.

-CCW checkbox is the angle direction. To invert the rotating direction, check CCW.

-Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

-Read interval is the SSI stream readout and refresh rate the GUI.

Position of the magnet

Status bits and field alarm

Set the actual angle as

Zero Position

Counter Clockwise mode

Selected die

(dual die AS52xx devices only)

AS5043-PB ZIF socket board

Device selection for autodetect:

-Jumper position 1: AS5043

Pin 1

www.ams.com

Revision 1.11/ 02/18/2014

Application Note –AS5000 Programmer

Figure 11: OTP tab of AS5043, with FBintE N option checked by user

AS5043:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is

possible to check the effect of the new configuration.

Zap! Writes permanently the checked OTP bits to the encoder’s fuses.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMS Hauptplatine Handbücher

AMS

AMS AS3956 Bedienungsanleitung

AMS

AMS TMD2620-DB Bedienungsanleitung

AMS

AMS TSL2772 EVM Bedienungsanleitung

AMS

AMS AS5 47 Series Bedienungsanleitung

AMS

AMS AS5000 Bedienungsanleitung

AMS

AMS TSL2572 EVM Bedienungsanleitung

AMS

AMS AS5 47D-TO EK ST Series Bedienungsanleitung

AMS

AMS AS3460 Bedienungsanleitung

AMS

AMS AS726x-iSPI Bedienungsanleitung

AMS

AMS AS5 Series Bedienungsanleitung

AMS

AMS TMF882X Bedienungsanleitung

AMS

AMS AS7058 Bedienungsanleitung

AMS

AMS AS5600 Bedienungsanleitung

AMS

AMS OSRAM NanEye Bedienungsanleitung

AMS

AMS TSL2540 EVM Bedienungsanleitung

AMS

AMS AS3935 Bedienungsanleitung

AMS

AMS TMD2636 EVM Bedienungsanleitung

AMS

AMS AS703X_EVALKIT_BT Bedienungsanleitung

AMS

AMS TSL2540 EVM Bedienungsanleitung

AMS

AMS TCS3720 Bedienungsanleitung

AMS

AMS TMF8821-SHIELD Bedienungsanleitung

AMS

AMS USB I&P Box Bedienungsanleitung

AMS

AMS CCS811 Bedienungsanleitung

AMS

AMS AS5-Series-47 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung