AMS USB I&P Box Bedienungsanleitung

www.ams.com Revision 1.2 / 06/10/2014 page 1/9

USB Interface &

Programming Box

Evaluation Programmer for SPI & I2C Interface

USB I&P Box User Manual

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 2/9

Table of Contents

1General Description ............................................................................................................. 3

2Hardware.............................................................................................................................. 4

2.1 Kit Content ........................................................................................................................... 4

2.2 Compatible Products............................................................................................................ 4

2.3 Pin-out.................................................................................................................................. 5

3First steps with the USB I&P Box......................................................................................... 5

4Software............................................................................................................................... 7

4.1 GUI Overview....................................................................................................................... 7

4.2 Firmware Update.................................................................................................................. 8

5Ordering Information............................................................................................................ 8

Copyright ............................................................................................................................................. 9

Disclaimer............................................................................................................................................ 9

Revision History

Revision

Date

Owner

Description

1.0

21.01.2014

AZEN

Initial revision

1.1

06.08.2014

RPH

Minor changes

1.2

06.10.2014

AZEN

Updated Compatible Products

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 3/9

1 General Description

This Manual explains how to use the USB I&P Box.

The USB I&P Box is a Programming-Tool for Magnetic Position Sensors with I2C or SPI Interface.

After connecting a Magnetic Position Sensor to I&P Box you can open the GUI on your computer

and start programming.

For programming a Magnetic Position Sensor the sensor should be mounted on a PCB to get

connected with all the necessary pins of the sensor.

For Position Sensors, ams provides Adapterboards where an easy access from the Sensor to the

USB I&P Box is possible (not in the Tool-Kit included)

Figure 1:

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 4/9

2 Hardware

2.1 Kit Content

Table 1:

USB I&P Box Kit content

Part

Description

Picture

USB I&P Box

USB Interface & Programming Box

USB cable

To connect the USB I&P box

10-way cable

To connect the USB I&P Box to a

compatible sensor on an existing

board

Quick Start Guide

First steps introduction

USB flash drive

Contains the USB I&P Box

Software and manuals.

2.2 Compatible Products

Table 2:

Compatible Products

Product

Description

Adapterboard available

AS5047D

14-bit On-Axis Magnetic Rotary Position Sensor

yes

AS5048A

14-bit Angular Position Sensor with SPI Interface

yes

AS5048B

14-bit Angular Position Sensor with I2C Interface

yes

AS5050A

Low Power 10-Bit Magnetic Position Sensor

yes

AS5055A

Low Power 12-Bit Magnetic Position Sensor

yes

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 5/9

Product

Description

Adapterboard available

AS5147

14-bit On-Axis Magnetic Rotary Position Sensor

yes

AS5510

Linear Hall Sensor with I²C Output

yes

AS5600

12-bit Programmable Contactless Potentiometer

yes

AS5601

12-bit Programmable Contactless Encoder

yes

2.3 Pin-out

The pin-out of the USB I&P box is shown below in Table 3

Table 3:

USB I&P Box Pin-out and wire description

Note: The interface voltage of the USB I&P Box is 3,3V. Use the 3,3V mode when connecting to a

position sensor board.

3 First steps with the USB I&P Box

The first steps to get started with the USB I&P Box are described below in Figure 2.

Pin #

Color

Definition

SPI Mode

Brown

5V Supply

Not used

Red

3.3V Supply

Positive power supply

Orange

SPI-CS(0)

Yellow

I2C-SCL

Not used

Green

SPI-CLK

Blue

I2C-SDA

Not used

Purple

SPI-MOSI

Grey

SPI-CS(1)

Optional (dual die version)

White

SPI-MISO

Black

GND

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 6/9

Figure 2:

First steps with the USB I&P Box

Getting started with your programmer

Ready to start

Install the USB I&P Software on your

computer

Connect the right wires of the USB I&P

Connector cable to your magnetic position

sensor

Connect your USB I&P Box to your

computer via USB cable

Open the USB I&P Software

Choose the right Device

For using the right wires

please refer to Table 3

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 7/9

4 Software

4.1 GUI Overview

Also included in your USB I&P Tool is a USB stick with the software.

The software is needed for programming the Magnetic Position Sensor on your computer.

When you copied the software from the USB stick to your computer please click on it and follow

the instructions of the Install Wizard through the installing procedure.

The software is compatible for Windows XP and newer versions.

In Figure 3:you can have a look at the starting page after finishing the installing and no device

connected.

Figure 4 shows the GUI while a Programmer Box connected

Figure 3:

Screenshot of the GUI’s starting page while no Programmer is connected

A: Select the Device (only possible when a I&P Box is detected)

B: Check if the Programmer will be detected (or there is no bootloader on the I&P Box)

C: For firmware updates click on Help and Firmware Update, for further Information about

this topic refer to 4.2

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 8/9

Figure 4:

Screenshot of the GUI’s starting page while Programmer connected

4.2 Firmware Update

Connect your I&P Box to your Computer and open the Software

Click on Help and Firmware Update

Search your computer for the new firmware file and click at it

After that the firmware installs by itself and the update is successful

5 Ordering Information

Table 4:

Ordering Information

Ordering Code

Description

USB I&P Box

USB Interface & Programming box for I2C/SPI

USB I&P Box

User Manual

www.ams.com Revision 1.2 / 06/10/2014 page 9/9

translated, stored, or used without the prior written consent of the copyright owner.

Disclaimer

Demo Kits, Evaluation Kits and Reference Designs are provided on an “as is” basis for demonstration

and evaluation purposes only. Any express or implied warranties, including, but not limited to the

implied warranties of merchantability and fitness for a particular purpose are disclaimed. Any claims

and demands and any direct, indirect, incidental, special, exemplary or consequential damages

arising from the inadequacy of the provided Demo Kits, Evaluation Kits and Reference Designs or

incurred losses of any kind (e.g. loss of use, data or profits, or business interruption however caused)

as a consequence of their use are excluded.

Contact Information

Headquarters

ams AG

Tobelbader Strasse 30

8141 Unterpremstaetten

Austria

T. +43 (0) 3136 500 0

For Sales Offices, Distributors and Representatives, please visit:

http://www.ams.com/contact

Inhaltsverzeichnis

Andere AMS Hauptplatine Handbücher

AMS

AMS AS5270-MF_EK_SB Bedienungsanleitung

AMS

AMS TSL2772 EVM Bedienungsanleitung

AMS

AMS AS7058 Bedienungsanleitung

AMS

AMS TMD2620 Bedienungsanleitung

AMS

AMS TCS3701 Bedienungsanleitung

AMS

AMS TSL2540 EVM Bedienungsanleitung

AMS

AMS TSL2540 EVM Bedienungsanleitung

AMS

AMS TCS3 7 Series Bedienungsanleitung

AMS

AMS AS5047P-TS_EK_AB Bedienungsanleitung

AMS

AMS AS5 47 Series Bedienungsanleitung

AMS

AMS AS3930 Bedienungsanleitung

AMS

AMS TDC-GPX2 Bedienungsanleitung

AMS

AMS AS6204 Bedienungsanleitung

AMS

AMS AS621 Series Bedienungsanleitung

AMS

AMS AS5048 Eval-Kit Handbuch

AMS

AMS TSL2541 Bedienungsanleitung

AMS

AMS AS5600 Bedienungsanleitung

AMS

AMS TCS3707 EVM Bedienungsanleitung

AMS

AMS CCS811 Bedienungsanleitung

AMS

AMS TCS3414 EVM2 Bedienungsanleitung

AMS

AMS TMD2636 EVM Bedienungsanleitung

AMS

AMS TMD2620-DB Bedienungsanleitung

AMS

AMS AS5600 Bedienungsanleitung

AMS

AMS TSL2584TSV Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung