Analog Devices LINEAR TECHNOLOGY LTC5577 Bedienungsanleitung

dc2070afa

DEMO MANUAL DC2070A

DESCRIPTION

LTC5577

300MHz to 6GHz

High Signal Level Active

Downconverting Mixer

DemonstrationcircuitDC2070Aisoptimizedfor evaluation

of the LT C

5577 high signal level active downconverting

mixer. Its RF input port is matched to 50Ω from 1.3GHz to

4.3GHz with 12dB return loss, and the LO port is matched

to 50Ω from 930MHz to 4.1GHz with 10dB return loss.

The RF and LO inputs are easily matched for higher or

lower frequencies with simple external matching, as low

as350MHz and 300MHz, respectively. The low capacitance

differential IF output is usable up to 1.5GHz. The LTC5577

active mixer is optimized for RF downconverting applica-

tions that require high input signal handling capability and

wide bandwidth.

Design files for this circuit board are available at

http://www.linear.com/demo

L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Analog

Devices, Inc. All other trademarks are the property of their respective owners.

Figure 1. Test Setup for Mixer 2-Tone Measurements

ABSOLUTE MAXIMUM INPUT

RATINGS

Supply Voltage (VCC, IF+, IF–).....................................4V

Enable Input Voltage (EN)................–0.3V to VCC + 0.3V

LO Input Power (300MHz to 6GHz)......................10dBm

LO Input DC Voltage............................................... ±0.1V

RF Input Power (300MHz to 6GHz)......................18dBm

RF Input DC Voltage............................................... ±0.1V

TEMP Monitor Input Current..................................10mA

Operating Temperature Range (TC)........ –40°C to 105°C

Junction Temperature (TJ).................................... 150°C

Storage Temperature Range .................. –65°C to 150°C

CAUTION: THIS PART IS SENSITIVE TO ELECTRO-

STATIC DISCHARGE (ESD). OBSERVE PROPER ESD

PRECAUTIONS WHEN HANDLING THE LTC5577.

BOARD PHOTO

Downloaded from Arrow.com.

dc2070afa

DEMO MANUAL DC2070A

NOTES ON TEST EQUIPMENT AND SETUP

QUICK START PROCEDURE

n High performance signal generators with low harmonic

outputs should be used for 2-tone measurements.

Otherwise, low pass filters at the signal generator out-

puts should be used to suppress harmonics.

n High quality combiners should be used to present a

broadband 50Ω termination on all ports as well as

provide good port-to-port isolation. Attenuator pads

should be used on the inputs to the combiner and the RF

input port of the LTC5577 mixer, as shown in Figure 1.

Adding attenuator pads further improves source iso-

lation and helps prevent the signal generators from

producing intermodulation products.

1. Set the power supply output voltage to 3.3V and the

current limit to 250mA. Turn off the power supply

output.

2. Connect all test equipment and the power supply as

shown in Figure 1.

n Spectrum analyzers can produce significant internal

distortion products if they are overdriven. Generally,

spectrum analyzers are designed to operate at their

best with about –30dBm to –40dBm at their input. The

spectrum analyzer’s input attenuation setting should

be used to avoid saturating the instrument. Set the

spectrum analyzer’s input attenuation depending on

the spectrum analyzer used.

n Before performing measurements on the DUT, the

system performance should be evaluated to ensure that

a clean input signal is obtained and that the spectrum

analyzer’s internal distortion is minimized

3. Ramp on the power supply with a minimum ramp time

of 1ms.

4. Set the LO signal generator to provide an 1800MHz

CW signal at about 0dBm at the DC2070A’s LO port.

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

1 4 C1, C2, C7, C8 CAP, 1nF, 10%, 16V, X7R, 0402 MURATA, GRM155R71C102KA01D

2 1 C3 CAP, 8.2pF, ±0.1pF, 50V, NPO, 0402 MURATA, GJM1555C1H8R2CA01D

3 1 C4 CAP, 0.7pF, ±0.1pF, 50V, NPO, 0402 MURATA, GJM1555C1HR70BB01D

4 1 C5 CAP, 3.9pF, ±0.1pF, 50V, NPO, 0402 MURATA, GJM1555C1H3R9BB01D

5 0 R3, L4, L5, L6, C6, C10, C11,

C12, C13

COMP, 0402, OPT 0402

6 1 C9 CAP, 1µF, 10%, 10V, X7R, 0603 MURATA, GRM188R61A105KA61D

7 3 E1, E3, E4 TURRET, PAD, 0.094" MILL-MAX, 2501-2-00-80-00-00-07-0

8 1 E2 TURRET, PAD, 0.061" MILL-MAX, 2308-2-00-80-00-00-07-0

9 4 J1-J4 CONN, SMA, 50Ω, EDGE-LAUNCH E.F. JOHNSON, 142-0701-851

10 2 L1, L2 IND, 560nH, 2%, 0603 COILCRAFT, 0603LS-561XGL

11 2 R1, R2 RES, CHIP, 115, 1%, 0402 VISHAY, CRCW0402115RFKED

12 1 U1 IC, LINEAR TECHNOLOGY, LTC5577IUF,

QFN16, 4×4

LINEAR TECHNOLOGY, LTC5577IUF

Downloaded from Arrow.com.Downloaded from Arrow.com.

dc2070afa

DEMO MANUAL DC2070A

SCHEMATIC DIAGRAM

Figure 2. High Signal Level Active Mixer

5. Set the two RF signal generators to provide one

1949MHz CW signal and one 1951MHz CW signal.

The signals should be applied to the 0° combiner. The

power applied to the DC2070A’s RF input port should

be about –3dBm/tone.

6. Perform various measurements (conversion gain, IP3,

LO leakage, etc.).

7. To turn off the DC2070A, either turn off the power sup-

ply’s output, or remove the power leads starting with

the EN lead.

QUICK START PROCEDURE

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

dc2070afa

DEMO MANUAL DC2070A

 LINEAR TECHNOLOGY CORPORATION 2013

LT 0417 REV A • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LT C ) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LT C for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LT C from all claims

arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LT C currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LT C applica-

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Inhaltsverzeichnis

Andere Analog Devices Hauptplatine Handbücher

Analog Devices

Analog Devices AD9910 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD5934EB Gebrauchsanweisung

Analog Devices

Analog Devices MICROCONVERTER ADUC7020 Bedienungsanleitung

Analog Devices

Analog Devices INEAR TECHNOLOGY DC2583A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices AD8450-EVALZ Bedienungsanleitung

Analog Devices

Analog Devices UG-173 Bedienungsanleitung

Analog Devices

Analog Devices AD9915 Bedienungsanleitung

Analog Devices

Analog Devices SSM2317 Bedienungsanleitung

Analog Devices

Analog Devices ADGM1004EBZ Bedienungsanleitung

Analog Devices

Analog Devices AD9864 Bedienungsanleitung

Analog Devices

Analog Devices SSM2167 Montage- und Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADF4360-8EBZ1 Bedienungsanleitung

Analog Devices

Analog Devices UG-185 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADG5404FEBZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD5423SDZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD7177-2SDZ Bedienungsanleitung

Analog Devices

Analog Devices DC353A Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD7276SDZ Bedienungsanleitung

Analog Devices

Analog Devices Linear Technology DC2622A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices DC2897A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices EVAL-AD7606C18FMCZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL–ADM2486EBZ Bedienungsanleitung

Analog Devices

Analog Devices ADuC7026 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD7723CB Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung