Anritsu InterferenceHunter MA2700A Bedienungsanleitung

User Guide

InterferenceHunter™

MA2700A

Handheld Direction Finding

System

Includes GPS and Electronic Compass

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

Part Number: 10580-00361

Revision: D

Published: October 2022

WARRANTY

The Anritsu product listed on the title page is warranted against defects in materials and

workmanship for one year from the date of shipment.

Anritsu’s obligation covers repairing or replacing products which prove to be defective

during the warranty period. Buyers shall prepay transportation charges for equipment

returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser.

Anritsu is not liable for consequential damages.

LIMITATION OF WARRANTY

The foregoing warranty does not apply to Anritsu connectors that have failed due to

normal wear. Also, the warranty does not apply to defects resulting from improper or

inadequate maintenance, unauthorized modification or misuse, or operation outside of the

environmental specifications of the product. No other warranty is expressed or implied,

and the remedies provided herein are the Buyer’s sole and exclusive remedies.

DISCLAIMER OF WARRANTY

DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL

WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCT. THE USER

ASSUMES THE ENTIRE RISK OF USING THE PRODUCT. ANY LIABILITY OF

PROVIDER OR MANUFACTURER WILL BE LIMITED EXCLUSIVELY TO PRODUCT

REPLACEMENT.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT

PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR

ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT

LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS

INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER

PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE

PRODUCT, EVEN IF ANRITSU COMPANY HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE

LIMITATION MAY NOT APPLY TO YOU.

TRADEMARK ACKNOWLEDGMENTS

NOTICE

Anritsu Company has prepared this manual for use by Anritsu Company personnel and

customers as a guide for the proper installation, operation and maintenance of Anritsu

Company equipment and computer programs. The drawings, specifications, and

information contained herein are the property of Anritsu Company, and any unauthorized

use or disclosure of these drawings, specifications, and information is prohibited; they

shall not be reproduced, copied, or used in whole or in part as the basis for manufacture or

sale of the equipment or software programs without the prior written consent of Anritsu

Company.

MA2700A UG PN: 10580-00361 Rev. D Title-3

Notes On Export Management

This product and its manuals may require an Export License or

approval by the government of the product country of origin for

re-export from your country.

Before you export this product or any of its manuals, please contact

Anritsu Company to confirm whether or not these items are

export-controlled.

When disposing of export-controlled items, the products and manuals

need to be broken or shredded to such a degree that they cannot be

unlawfully used for military purposes.

UPDATES

Updates, can be downloaded from the Anritsu Website at:

http://www.anritsu.com/contact-us

Title-4 PN: 10580-00361 Rev. D MA2700A UG

CE Conformity Marking

European Parliament and Council Directive 2012/19/EU

RCM Conformity Marking

UKCA Conformity Marking

Anritsu affixes the CE Conformity marking onto its

conforming products in accordance with Council

Directives of The Council Of The European Communities

in order to indicate that these products conform to the

EMC, LVD, RoHS, and RED directives of the European

Union (EU).

Equipment Marked with the crossed-out Wheelie Bin

symbol complies with the European Parliament and

Council Directive 2012/19/EU (the “WEEE Directive”) in

the European Union.

For Products placed on the EU market after August 13,

2012, please contact your local representative at the end

of the product’s useful life to arrange disposal in

accordance with your initial contract and the local law.

Anritsu affixes the Regulatory Compliance Mark (RCM)

onto its conforming products in accordance with the

electromagnetic compliance regulations of Australia and

New Zealand in order to indicate that these products

conform to the EMC regulations of Australia and New

Zealand.

Anritsu affixes the UKCA Conformity marking onto its

conforming products in accordance with the United

Kingdom conformity assessment body (CAB) in order to

indicate that these products conform to the market of

Great Britain (England, Wales, and Scotland).

MA2700A UG PN: 10580-00361 Rev. D Title-5

KCC Conformity Marking

Recycle Marking

Canadian ICES-001 Conformity Marking

Anritsu affixes the Korean Communications Commissions

(KCC) mark onto its conforming products in accordance

with the electromagnetic compliance regulations of Korea

Anritsu affixes the universal recycle symbol onto its

products to indicate that the marked part is made from

recyclable materials and should be recycled. Materials

should be recycled in accordance with your local

regulatory requirements.

CAN/ICES-1

(A)/NMB-1(A)

Anritsu affixes the CAN ICES-1(A)/NMB-1(A) compliance

label onto its conforming products in accordance with the

following Canadian Interference-Causing Equipment

Standards.

ICES-001 — Industrial, Scientific and Medical (ISM)

Radio Frequency Generators

Title-6 PN: 10580-00361 Rev. D MA2700A UG

Chinese RoHS Compliance Statement

MA2700A UG PN: 10580-00361 Rev. D Safety-1

Safety Symbols

To prevent the risk of personal injury or loss related to product

malfunction, Anritsu Company uses the following symbols to indicate

safety-related information. For your own safety, please read the

information carefully before operating the product.

Symbols Used in Manuals

Danger

This indicates a risk from a very dangerous condition or

procedure that could result in serious injury or death and

possible loss related to product malfunction. Follow all

precautions and procedures to minimize this risk.

Warning This indicates a risk from a hazardous condition or

procedure that could result in light-to-severe injury or

loss related to product malfunction. Follow all

precautions and procedures to minimize this risk.

Caution

This indicates a risk from a hazardous procedure that

could result in loss related to product malfunction.

Follow all precautions and procedures to minimize this

risk.

Safety-2 PN: 10580-00361 Rev. D MA2700A UG

Safety Symbols Used on Product and in Manuals

The following safety symbols are used inside or on the product near

operation locations to provide information about safety items and

operation precautions. Ensure that you clearly understand the

meanings of the symbols and take the necessary precautions before

operating the product. Some or all of the following five symbols may or

may not be used on all Anritsu products. In addition, there may be other

labels attached to products that are not shown in the diagrams in this

manual.

This indicates a prohibited operation. The prohibited

operation is indicated symbolically in or near the barred

circle.

This indicates a compulsory safety precaution. The

required operation is indicated symbolically in or near the

circle.

This indicates a warning or caution. The contents are

indicated symbolically in or near the triangle.

This indicates a note. The contents are described in the

box.

These indicate that the marked part should be recycled.

MA2700A UG PN: 10580-00361 Rev. D Safety-3

For Safety

Danger

Using the MA2700A InterferenceHunter while a

car is in motion could be dangerous and lead to

serious accidents.

Warning

Always refer to the operation manual when

working near locations at which the alert mark,

shown on the left, is attached. If the operation,

etc., is performed without heeding the advice in

the operation manual, there is a risk of personal

injury. In addition, the product performance may

be reduced. Moreover, this alert mark is

sometimes used with other marks and

descriptions indicating other dangers.

Warning

This product can not be repaired by the operator.

Do not attempt to remove the product covers or

to disassemble internal components. Only

qualified service technicians with a knowledge of

electrical fire and shock hazards should service

this product. There are high-voltage parts in this

product presenting a risk of severe injury or fatal

electric shock to untrained personnel. In addition,

there is a risk of damage to precision

components.

Safety-4 PN: 10580-00361 Rev. D MA2700A UG

For Safety

Caution

Electrostatic Discharge (ESD) can damage the

highly sensitive circuits in the instrument. ESD is

most likely to occur as test devices are being

connected to, or disconnected from, the

instrument’s front and rear panel ports and

connectors. You can protect the instrument and

test devices by wearing a static-discharge

wristband. Alternatively, you can ground yourself

to discharge any static charge by touching the

outer chassis of the grounded instrument before

touching the instrument’s front and rear panel

ports and connectors. Avoid touching the test

port center conductors unless you are properly

grounded and have eliminated the possibility of

static discharge.

Repair of damage that is found to be caused by

electrostatic discharge is not covered under

warranty.

Inhaltsverzeichnis

Andere Anritsu Prüfgeräte Handbücher

Anritsu

Anritsu 3656B W1 Bedienungsanleitung

Anritsu

Anritsu MT8860B Betriebsanleitung

Anritsu

Anritsu MN469xC Series Bedienungsanleitung

Anritsu

Anritsu MT8852A Bedienungsanleitung

Anritsu

Anritsu 691 B Series Bedienungsanleitung

Anritsu

Anritsu MP1800A Bedienungsanleitung

Anritsu

Anritsu MG3681A Bedienungsanleitung

Anritsu

Anritsu Precision AutoCal 36585 Series Bedienungsanleitung

Anritsu

Anritsu VectorStar MN4690B Series Bedienungsanleitung

Anritsu

Anritsu MT8870A Bedienungsanleitung

Anritsu

Anritsu LMR Master S412E Betriebsanleitung

Anritsu

Anritsu MT1000A Network Master Pro Bedienungsanleitung

Anritsu

Anritsu 681XXC Bedienungsanleitung

Anritsu

Anritsu MT8850A Bedienungsanleitung

Anritsu

Anritsu MT8852B Betriebsanleitung

Anritsu

Anritsu MP1800A Bedienungsanleitung

Anritsu

Anritsu ME7840A Bedienungsanleitung

Anritsu

Anritsu MT1000A Network Master Pro Bedienungsanleitung

Anritsu

Anritsu MS9720A Bedienungsanleitung

Anritsu

Anritsu Site Master S330A Bedienungsanleitung

Anritsu

Anritsu MT1000A Network Master Pro Bedienungsanleitung

Anritsu

Anritsu MG3641A Bedienungsanleitung

Anritsu

Anritsu MT1000A Network Master Pro Bedienungsanleitung

Anritsu

Anritsu MT8860C Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung