Anritsu MP1800A Bedienungsanleitung

Document No.: M-W3756AE-5.0

ANRITSU CORPORATION

MP1861A

56G/64Gbit/s MUX

Operation Manual

Fifth Edition

•For safety and warning information, please read this

manual before attempting to use the equipment.

•

Additional safety and warning information is provided

in the MP1800A Signal Quality Analyzer

Installation

Guide and the MT1810A 4 Slot Chassis

Installation

Guide. Please also refer to one of the

m before using

the equipment.

•

Keep this manual with the equipment.

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MP1861A 56G/64Gbit/s MUX

Operation Manual

15 May 2015 (First Edition)

25 August 2020 (Fifth Edition)

publisher.

The operational instructions of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

•ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed, there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the left

may also be used with other marks and descriptions to indicate other

dangers.

•Overvoltage Category

This equipment complies with overvoltage category II defined in IEC

61010. DO NOT connect this equipment to the power supply of

overvoltage category III or IV.

•To ensure that the equipment is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

•Only qualified service personnel with a knowledge of electrical fire

and shock hazards should service this equipment. This equipment

cannot be repaired by the operator. DO NOT attempt to remove the

equipment covers or unit covers or to disassemble internal

components. There are high-voltage parts in this equipment

presenting a risk of severe injury or fatal electric shock to untrained

personnel. In addition, there is a risk of damage to precision

components.

Electric Shock

Repair

For Safety

WARNING

•The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu

service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the

equipment or unit covers. If the performance-guarantee seal is

broken by you or a third party, the performance of the equipment

cannot be guaranteed.

•This equipment should always be positioned in the correct manner. If

the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

Falling Over

Calibration

For Safety

CAUTION

•Always remove the main power cable from the power outlet before

cleaning dust around the power supply and fan.

- Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

- Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

•Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

This equipment is designed for an industrial environment.

In a residential environment, this equipment may cause radio

interference in which case the user may be required to take adequate

measures.

Exposure to corrosive gases such as hydrogen sulfide, sulfurous acid,

and hydrogen chloride will cause faults and failures.

Note that some organic solvents release corrosive gases.

Cleaning

Check Terminal

Use in a

Residential

nvironment

Use in

Corrosive

Atmospheres

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before shipment

using calibrated measuring instruments with direct traceability to public

testing organizations recognized by national research laboratories, including

the National Institute of Advanced Industrial Science and Technology, and

the National Institute of Information and Communications Technology, and

was found to meet the published specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a malfunction

occurs within one year after shipment due to a manufacturing fault, and

software bug fixes will be performed in accordance with the separate Software

End-User License Agreement, provide, however, that Anritsu Corporation will

deem this warranty void when:

•The fault is outside the scope of the warranty conditions separately

described in the operation manual.

•The fault is due to mishandling, misuse, or unauthorized modification or

repair of the equipment by the customer.

•The fault is due to severe usage clearly exceeding normal usage.

•The fault is due to improper or insufficient maintenance by the customer.

•The fault is due to natural disaster, including fire, wind, or flood,

earthquake, lightning strike, or volcanic ash, etc.

•The fault is due to damage caused by acts of destruction, including civil

disturbance, riot, or war, etc.

•The fault is due to explosion, accident, or breakdown of any other

machinery, facility, or plant, etc.

•The fault is due to use of non-specified peripheral or applied equipment

or parts, or consumables, etc.

•The fault is due to use of a non-specified power supply or in a

non-specified installation location.

•The fault is due to use in unusual environments(Note).

•The fault is due to activities or ingress of living organisms, such as

insects, spiders, fungus, pollen, or seeds.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for damage or financial loss of the

customer due to the use of or a failure to use this equipment, unless the

damage or loss is caused due to Anritsu Corporation’s intentional or gross

negligence.

vii

Note:

For the purpose of this Warranty, "unusual environments" means use:

•In places of direct sunlight

•In dusty places

•Outdoors

•In liquids, such as water, oil, or organic solvents, and medical fluids, or

places where these liquids may adhere

•In salty air or in place chemically active gases (sulfur dioxide, hydrogen

sulfide, chlorine, ammonia, nitrogen dioxide, or hydrogen chloride etc.)

are present

•In places where high-intensity static electric charges or electromagnetic

fields are present

•In places where abnormal power voltages (high or low) or instantaneous

power failures occur

•In places where condensation occurs

•In the presence of lubricating oil mists

•In places at an altitude of more than 2,000 m

•In the presence of frequent vibration or mechanical shock, such as in

cars, ships, or airplanes

Anritsu Corporation Contact

In the event of this equipment malfunctions, please contact an Anritsu

Service and Sales office. Contact information can be found on the last page

of the printed version of this manual, and is available in a separate file on the

PDF version.

viii

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re

export from your

country.

Before re

exporting the product or manuals, please contact us to confirm

whether they are export

-controlled items or not.

When you dispose of export

-controlled item

s, the products/manuals need

to be broken/shredded so as not to be unlawfully used for military purpose.

Crossed-out Wheeled Bin Symbol

Equipment marked with the Crossed-out Wheeled Bin Symbol complies with

council directive 2012/19/EU (the “WEEE Directive”) in European Union.

For Products placed on the EU market after August 13, 2005, please contact

your local Anritsu representative at the end of the product's useful life to

arrange disposal in accordance with your initial contract and the local law.

Software End-User License Agreement (EULA)

Please carefully read and accept this Software End-User License Agreement (hereafter this EULA)

before using (includes executing, copying, installing, registering, etc.) this Software (includes programs,

databases, scenarios, etc., used to operate, set, etc., Anritsu electronic equipment, etc.). By using this

Software, you shall be deemed to have agreed to be bound by the terms of this EULA, and Anritsu

Corporation (hereafter Anritsu) hereby grants you the right to use this Software with the

Anritsu-specified equipment (hereafter Equipment) for the purposes set out in this EULA.

Article 1. Grant of License and Limitations

1. You may not to sell, transfer, rent, lease,

lend, disclose, sublicense, or otherwise

distribute this Software to third parties,

whether or not paid therefor.

2. You may make one copy of this Software for

backup purposes only.

3. You are not permitted to reverse engineer,

disassemble, decompile, modify or create

derivative works of this Software.

4. This EULA allows you to install one copy of

this Software on one piece of Equipment.

Article 2. Disclaimers

To the extent not prohibited by law, in no

event shall Anritsu be liable for direct, or

any incidental, special, indirect or

consequential damages whatsoever,

including, without limitation, damages for

loss of profits, loss of data, business

interruption or any other commercial

damages or losses, and damages claimed by

third parties, arising out of or related to your

use or inability to use this Software, unless

the damages are caused due to Anritsu’s

intentional or gross negligence.

Article 3. Limitation of Liability

1. If a fault (bug) is discovered in this Software,

failing this Software to operate as described

in the operation manual or specifications

even though you have used this Software as

described in the manual, Anritsu shall at its

own discretion, fix the bug, or replace the

software, or suggest a workaround,

free-of-charge, provided, however, that the

faults caused by the following items and any

of your lost or damaged data whatsoever

shall be excluded from repair and the

warranty.

i) If this Software is deemed to be used

for purposes not described in the

operation manual or specifications.

ii) If this Software has been used in

conjunction with other

non-Anritsu-approved software.

iii) If this Software or the Equipment has

been modified, repaired, or otherwise

altered without Anritsu's prior

approval.

iv) For any other reasons out of Anritsu's

direct control and responsibility, such

as but not limited to, natural disasters,

software virus infections, or any

devices other than this Equipment, etc.

2. Expenses incurred for transport, hotel, daily

allowance, etc., for on-site repairs or

replacement by Anritsu engineers

necessitated by the above faults shall be

borne by you.

3. The warranty period for faults listed in

Section 1 of this Article shall be either 6

months from the date of purchase of this

Software or 30 days after the date of repair

or replacement, whichever is longer.

Andere Handbücher für MP1800A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Anritsu Prüfgeräte Handbücher

Anritsu

Anritsu MG3641A Bedienungsanleitung

Anritsu

Anritsu MS8911A Bedienungsanleitung

Anritsu

Anritsu Network Master Series Bedienungsanleitung

Anritsu

Anritsu MT9810A Bedienungsanleitung

Anritsu

Anritsu Precision AutoCal 36585 Series Bedienungsanleitung

Anritsu

Anritsu LMR Master S412E Betriebsanleitung

Anritsu

Anritsu MT8860B Betriebsanleitung

Anritsu

Anritsu MG3641A Bedienungsanleitung

Anritsu

Anritsu ML8720B Bedienungsanleitung

Anritsu

Anritsu ME7840A Bedienungsanleitung

Anritsu

Anritsu 681XXC Bedienungsanleitung

Anritsu

Anritsu MT8870A Bedienungsanleitung

Anritsu

Anritsu 693 B Series Bedienungsanleitung

Anritsu

Anritsu MS8608A Bedienungsanleitung

Anritsu

Anritsu MP1800A Bedienungsanleitung

Anritsu

Anritsu 3656B W1 Bedienungsanleitung

Anritsu

Anritsu 691 B Series Bedienungsanleitung

Anritsu

Anritsu MX900030A Bedienungsanleitung

Anritsu

Anritsu MD8480A Bedienungsanleitung

Anritsu

Anritsu MG3681A Bedienungsanleitung

Anritsu

Anritsu MT9810A Bedienungsanleitung

Anritsu

Anritsu MP1590B Bedienungsanleitung

Anritsu

Anritsu Site Master S251B Bedienungsanleitung

Anritsu

Anritsu MT9810B Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung