ANTAIRA LMP-1202M-SFP Series Bedienungsanleitung

Antaira Industrial Ethernet Switches

LMP

-1002G-SFP Series User Manual V1.0

LMP-1202M-SFP Series

(LMP-1202M-SFP / LMP-1202M-SFP-T)

12-Port Industrial PoE+ Gigabit Managed Ethernet Switch with

8*10/100Tx (30W/Port), 2*10/100/1000Tx RJ45 and 2*100/1000 SFP Slots

Hardware Manual

Version 1.0

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

This document contains information, which is protected by copyright. Reproduction, adaptation or translation

without prior permission is prohibited, except as allowed under the copyright laws.

Trademark Information

Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the

trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the

registered trademarks of Wi-Fi Alliance. All other brand and product names are trademarks or registered

trademarks of their respective owners.

translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the

Disclaimer

Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but

not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,

LLC may make improvements and/or changes to the product and/or specifications of the product described in this

manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or

typographical errors found in this guide. Changes are periodically made to the information contained herein and

will be incorporated into later versions of the manual. The information contained is subject to change without prior

notice.

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

iii

FCC Warning

This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause

harmful interference to radio communications if the equipment is not installed and used in accordance with the

instructions. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.

•Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's

authority to operate the equipment.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which case the

user may be required to take adequate measures.

Industrial Ethernet Switches

Industrial Grade Gigabit PoE Managed Ethernet Switches

Hardware Manual

Version 1.0 (June 2019)

This manual supports the following models:

•LMP-1202M-SFP

•LMP-1202M-SFP-T

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

ATEX Certification

ATEX Marking String: II 3G Ex nA nC IIC T4 Gc

ATEX Certificate No.: DEMKO 18 ATEX 2104X

Standards: EN 60079-0:2012 + A11:2013, EN 60079-15:2010

Temperature code: T4

Specific Conditions of Use

•The equipment shall be installed in an enclosure that provides a degree of protection not less than IP 54 in

accordance with EN 60079-15 and accessible only by the use of a tool. In addition, the equipment shall only be

used in an area of not more than pollution degree 2 as defined in EN 60664-1.

•Provisions shall be made to prevent the rated voltage from being exceeded by transient disturbances of more

than 140%.

•Conductors suitable for use in an ambient temperature of 105.7°C must be used for the Power Supply Terminal

•The external grounding conduct shall be at least 4 mm2.

WARNING: EXPLOSION HAZARD – Do not disconnect while the circuit is live or unless the area is free of ignitable

concentrations.

This document is the current official release manual. Please check our website (www.antaira.com) for any

updated manual or contact us by e-mail (support@antaira.com) or address (780 Challenger Street, Brea,

CA 92821, USA)

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

Table of Contents

Introduction ........................................................................... 1

1.1 Product Overview 1

1.2 Product Software Features 1

1.3 Product Hardware Features 2

1.4 Package Contents 3

1.5 Safety Precaution 3

Hardware Description ........................................................... 4

2.1 Physical Dimensions 4

2.2 Front Panel 5

2.3 Top View 5

2.4 LED Indicators 6

2.5 Reset Button 7

2.6 Ethernet Ports 7

2.7 Cabling 8

2.8 Wiring the Power Inputs 11

2.9 Wiring the Fault Alarm Contact 11

2.10 Grounding Note 12

Mounting Installation........................................................... 13

3.1 DIN-Rail Mounting 13

3.2 Wall Mounting 14

Hardware Installation .......................................................... 15

4.1 Installation Steps 15

4.2 Maintenance and Service 15

Technical Specifications .................................................... 16

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

Introduction

All Antaira industrial managed switches come with a pre-installed “user friendly” web console interface,

which allows users to easily configure and manage the units, whether one is using a serial console and

command line interface(CLI) commands like Telnet, SSH, HTTP (Web GUI) or simple network

management protocols (SNMP).

1.1

Product Overview

Antaira’s LMP-1202M-SFP series is a 12-port industrial PoE+ managed Ethernet switch that is

embedded with 8*10/100Tx Ethernet ports that support IEEE802.3at/af for a maximum of

30W/port, 2*10/100/1000Tx RJ45 and 2*100/1000 dual rate SFP slots for Gigabit fiber

connections. The LMP-1202M-SFP series is a fully manageable Layer 2 Ethernet switch that is

pre-loaded with a user-friendly web management console design. It supports the ring network

redundancy function using the market’s open standard ITU-T G.8032 ERPS (Ethernet Ring

Protection Switch) protocol that has a <50ms network recovery time. The advanced network

filtering and security functions, such as, IGMP, VLAN, QoS, SNMP, RMON, ModbusTCP, and

802.1X/HTTPS/SSH/SSL increase determinism and improve network management for remote

SCADA systems or control networks.

The LMP-1202M-SFP series is IP30 rated and DIN-rail mountable. There are also two wide

operating temperature models for either a standard temperature range (STD: -10°C to 70°C) or an

extended temperature range (EOT: -40°C to 75°C). It also provides high EFT and ESD protection

for industrial networking applications, such as, power/utility, water wastewater, oil/gas/mining,

factory automation, security surveillance within transportation, ITS and any other outdoor or harsh

environment.

1.2

Product Software Features



Network Redundancy



STP, RSTP, MSTP, ITU-T G.8032 Ethernet Ring Protection Switch (ERPS) for network

redundancy



Network Management



Web UI based management, SNMP v1/v2/v3, Serial Console



Qos, traffic classification QoS, Cos, bandwidth control for Ingress and Egress, broadcast

storm control, Diffserv



IEEE802.1q VLAN tagging, port-based VLAN support



IGMP snooping v1/v2, IGMP filtering / throttling, IGMP query up to 256 group

vii

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0



Supports IPv4/IPv6, RMON, MIB II, port mirroring, event syslog, DNS, NTP/SNTP,

HTTPS, SSH/SSL, TFTP



MODBUS TCP for SCADA system integration



Port Configuration



Status, statistics, mirroring, rate limiting, event syslog



Event Handling



Event notification by Email: Cold/Warm Start, Power Failure, Authentication, SNMP

trap and Fault Alarm Relay Output



Software Upgrade via TFTP and HTTP



Configuration Backup – USB Port

1.3

Product Hardware Features



System Interface and Performance

•

All RJ-45 ports support Auto MDI Function

•

Embedded 8*10/100Tx (PSE 30W/Port) RJ45 Ports, 2*10/100/1000Tx RJ45, and

2*100/1000 SFP Slots

•

Store-and-forward switching architecture

•

8K MAC address table

•

Power line EFT protection: 2,000VDC; Ethernet ESD protection: 6,000VDC



Power Input

•

DC 48~55V 5.5A redundant with a 6-pin removal terminal block

•

One user programmable alarm relay contact 24 VDC, 1A resistive

•

The power input specification is complied with the requirements of SELV (Safety Extra Low

Voltage), and the power supply should be complied with UL 61010-1 & UL 61010-2-201



Operating Temperature

•

LMP-1202M-SFP: -10°C to 70°C

•

LMP-1202M-SFP-T: -40°C to 75°C



Case/Installation

•

IP-30 protection metal housing

•

DIN-Rail and wall mount design

•

Installation in a Pollution Degree 2 industrial environment

viii

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

1.4

Package Contents

1– LMP-1202M-SFP series: 12-port industrial gigabit PoE+ managed Ethernet switch, with

8*10/100Tx (PSE 30W/Port), 2*10/100/1000Tx RJ45 and 2*100/1000 SFP Slots



1-Quick Installation Guide



2-Wall mounting brackets and screws



1-RJ45 to DB9 Serial Console cable



1-DC cable –18 AWG & DC jack 5.5x2.1mm

1.5

Safety Precaution

Attention: If the DC voltage is supplied by an external circuit, please use a protection

device on the power supply input. The industrial Ethernet switch’s hardware

specs, ports, cabling information, and wiring installation will be described

within this user manual.

Warning Labels

The caution label means that you should check the certain information on user manual when working with

the device. (Shown in Figure 1.1)

Figure 1.1 - Caution Label

This warning label is on the device, and means that the surface of the device is hot. (Shown in Figure 1.2)

Figure 1.2 - Hot Surface Warning Label

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

Hardware Description

2.1

Physical Dimensions

Figure 2.1, below, shows the physical dimensions of Antaira’s LMP-1202M-SFP series: 12-port

industrial PoE+ managed Ethernet switches, with 8*10/100Tx (PSE 30W/Port), 2*10/100/1000Tx

RJ45 and 2*100/1000 SFP slots.

(W x D x H) is 54mm x 99mm x 142mm

Figure 2.1

LMP-1202M-SFP Series Physical Dimensions

Antaira Technologies - Industrial Ethernet Switches

LMP-1202M-SFP Series Hardware Manual V1.0

2.2

Front Panel

The front panel of the LMP-1202M-SFP series industrial gigabit PoE+ managed Ethernet switch is

shown below in Figure 2.2.

Figure2.2 - The Front Panel of LMP-1202M-SFP Series

2.3

Top View

Figure 2.3, below, shows the top panel of the LMP-1202M-SFP series switch that is

equipped with one 6-pin removal terminal block connector for dual DC power inputs

48~55VDC.

Figure2.3 - Top Panel View of LMP-1202M-SFP Series

Console Port

LED for Power 1, Power 2,

Fault, Master, and Ring

6-Pin Removal Terminal Block (Power Input)

USB for Configuration Back-up

LAN# 9~10 – 10/100Tx RJ45

LAN# 1~8 – 10/100Tx RJ45

Reset Button

SFP# 11~12 – LED for Link/Activity Status

LAN# 9~10 – LED for Link/Activity Status

1000Mbps

LAN# 9~10 – LED for Link/Activity Status

10/100Mbps

SFP# 11~12 – 100/1000

Grounding Screw

LAN# 1~8 – LED for Link/Activity Status

10/100Mbps

LAN# 1~8 – LED for PoE Status

Andere Handbücher für LMP-1202M-SFP Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ANTAIRA Netzwerk-Router Handbücher

ANTAIRA

ANTAIRA LMP-0602-24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-1600G Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-1202G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA ARY-7235-AC-PD Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-2804GN-SFP-T Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1002C-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-500A Bedienungsanleitung

ANTAIRA

ANTAIRA ARS-7235-5E-AC Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0602 24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-0601G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0702G-SFP-24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-1202G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0702G-SFP-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-2004G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-0802C-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0601G-SFP-24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-0602 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0600-24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-C500G Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-2004G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0601G-SFP-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-1204GN-T Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-501AG-SFP-T Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0602 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung