Antec P193 Bedienungsanleitung

P193

SER

’

ANUAL

ABLE OF

ONTENTS

NTRODUCTION

1.1 Case Specifications.…..………………………………………………………………………………….. 3

1. Diagram…………………………………………………………………….…………………………………. 3

ARDWARE

NSTALLATION

UIDE

.1 Setting Up….…………………………………………………………………………………………………. 4

. Power Supply Installation……………………………………………………………………………… 4

.3 CP Series Power Supply Mount…………………………………………………………………….. 5

.4 Cable Management………………………………………………………………………………………. 5

.5 Motherboard Installation..……………………………………………………………………………. 5

.6 Internal 3.5” Device Installation……………………………………………………………………. 6

.7 External 3.5” Device Installation…………………………………………………………………… 7

.8 External 5. 5” Device Installation…………………………………………………………………. 7

ONNECTING THE

RONT

I/O

ORTS

3.1 USB .0 Ports………………………………………………….……………………………………………. 8

3. eSATA Ports…………………………………….……………………………………………………………. 8

3.3 AC’97 / HD Audio Ports……………………….………………………………………………………… 8

3.4 Switch and LED Connectors…………………………………………………………………………… 9

3.5 Rewiring Motherboard Header Connections………………………………………………… 9

OOLING

YSTEM

4.1 TriCool™ Fans ………………………………………………………………………………………………. 10

4. Optional Fans.………………………………………………………………………………………………. 11

4.3 Washable Air Filters………………………………………..……………………………………………. 1

P193

SER

’

ANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible

that your new case will differ slightly from the descriptions in this manual. As of the date of

publication, all features, descriptions, and illustrations in this manual are correct.

Dis

laim

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive

instructions on installing the motherboard and peripherals, please refer to the user’s manuals that

come with those components.

The P193 does not come with a power supply unit (PSU). Make sure you choose a power supply that is

compatible with your computer components and has a long enough power harness to reach your

motherboard and peripheral devices. We recommend our CP Series, TruePower Series or Signature

Series power supplies for the latest ATX specification compliance, broad compatibility, and energy-

saving capability.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend

taking the appropriate time and care when working with it. Avoid hurried or careless motions. Please

use reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the

motherboard manual for specific mounting instructions and troubleshooting. Before proceeding,

check the manual for your CPU cooler to find out if there are steps you must take before installing the

motherboard. While installing hardware, keep your case on a flat, stable surface.

1.1 C

ASE

PECIFICATIONS

Case Type

Advanced Mid Tower

Color

Gunmetal Gray

Dimensions

514mm (H) x 05mm (W) x 590mm (D)

0. 5" (H) x 8.1" (W) x 3. 5" (D)

* Actual clearance for width is 9.5”/ 41mm due to the side panel fan

Weight

35.8 lbs / 16. 5 kg

Cooling

x Rear 1 0mm TriCool

™

exhaust fan

- x Top 140mm exhaust TriCool™ fan

-1 x Side 00mm Big Boy 00™ fan for dual video cards

-1 x Lower (optional) chamber 1 0mm TriCool™ fan

-1 x Front (optional) 1 0mm fan mount for HDD

-1 x Middle (optional) 1 0mm fan mount for video cards

Drive

Bays

11 Drive Bays:

-4 x External 5. 5” drive bays

-1 x External 3.5” drive bay

-6 x Internal 3.5” drive bays

Expansion Slots 7

Motherboard Size

Mini-ITX, microATX, Standard ATX, Extended ATX

Front I/O Panel

x USB .0

1 x eSATA

AC’97 / HD Audio In and Out

IAGRAM

1. Rear 1 0mm TriCool™ fan

. Top 140mm TriCool™ fans

3. 00mm side Big Boy 00™ fan

4. Washable air filters

5. Motherboard mount

6. Power supply mount

7. 5. 5” drive bays

8. 3.5” hard drive bays

9. Front I/O panel

ARDWARE

NSTALLATION

UIDE

ETTING

1. Place the case upright on a flat, stable surface with the

rear of the case facing you.

. Remove the thumbscrews from the right side panel.

Grip the panel at the top and bottom and slide it toward

you to open the case.

3. Remove the screws from the left side panel. Grip the

panel at the top and bottom and slide it toward you to

remove the left side panel.

Note: Do not use your fingernails to pry or lift the

panels.

Inside the case you should see two separate chambers: the upper chamber for the motherboard,

externally accessible drives and hard drives; and the lower chamber for the power supply and hard

drives. You will also find some wiring with marked connectors (USB, PWR, etc.), the installed I/O panel,

a box containing one set each of drive rails for a 5. 5” drive and a floppy disk drive, and a tool box

attached to the upper HDD cage containing more hardware (screws, brass standoffs, spare silicone

grommets, etc.).

OWER

UPPLY

NSTALLATION

Most power cables can be routed behind the motherboard through the cable management

compartment. If some cables can’t reach, run them through the passage that goes straight into the

motherboard compartment.

1. Remove both side panels.

. If you are installing an Antec CP series power supply, you will need to

remove the PSU adapter plate.

3. Slide the power supply into the case. If not routing cables through the

cable management compartment behind the motherboard, route

cables through the covered opening. This will save a few inches of

cable travel and help improve airflow in the power supply

compartment.

Note: Power supplies with fans on the bottom will need to be

mounted so that the fan is facing the top of the case. There are

mounting holes for power supplies to be installed upside up or

upside down.

4. Secure the power supply by fastening it to the back of the case with

the provided screws.

ERIES

OWER

UPPLY

OUNT

Your Antec P193 enclosure

comes with a power supply mounting

adapter to mount either a standard-size power supply or the unique

Antec CP Series high-performance power supply. This adapter is

mounted to the chassis with standard Phillips-head screws. In order to

install the CP Series power supply, remove the mounting plate first.

ABLE

RGANIZERS

There is a cable management compartment between the motherboard and right side panel. You can

tuck or route excess cables in this compartment.

1. Remove both side panels.

. Choose the cables you would like to pass through the holes behind the motherboard tray and pull

them out of the power supply chamber toward the right side of the case.

3. Use the cable ties provided to hold them in place.

4. Feed the cables back through the insertion point nearest the destination of the cable. Connect the

cable and then pull the slack back to the right side of the case.

OTHERBOARD

NSTALLATION

1. Lay the case down, with the open side facing up. The

drive cages and power supply should be visible.

. Make sure you have the correct I/O panel for your

motherboard. If the panel provided with the case isn’t

suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Align your motherboard with the standoff holes and

remember which holes are lined up. Not all

motherboards will match with all the provided holes;

this is normal and won’t affect its functionality.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the motherboard

back in.

6. Screw in your motherboard to the standoffs with the

provided Phillips-head screws.

NTERNAL

3.5”

EVICE

NSTALLATION

With the front bezel facing you, swing the front door open. It can swing 70º so the door is parallel with

the side of the case. You can see there are four 5. 5” and one 3.5” external drive bays. Inside the case

there are two 3.5” drive cages, which can house up to six hard drives.

Note: We recommend using the lower HDD cage to maximize cooling and quiet computing.

Upper HDD Installation

1. Remove the thumbscrew holding the upper HDD cage.

. Pull the HDD cage from its position by pulling the ring toward you.

3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide

the tray out.

4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the

screws as this will reduce the vibration and noise dampening ability of the silicone grommets.

Note: Always mount the HDD with the thicker side of the silicone grommets facing up.

5. Slide and lock the tray back into the cage.

6. Slide the cage back into the case and fasten the thumbscrew.

7. Find the right Molex or SATA connector on the power supply and connect it to the hard drive.

8. Repeat the same procedure for the other drives.

Lower HDD Installation

1. Remove the thumbscrew holding the lower HDD cage.

. Pull the HDD cage from its position by pulling the ring towards

you.

3. You can mount up to four hard drives inside the cage. They are

mounted vertically with the silicone grommets sitting at both

sides.

4. Mount your hard drive into the drive cage with the special screws

provided. Don’t over-tighten the screws as this will reduce the

vibration and noise dampening ability of the silicone grommets.

Note: Always mount the HDD with the thicker side of the silicone

grommets facing up.

5. Slide the cage back into the case and fasten the thumbscrew.

6. Find a Molex or SATA connector on the power supply and connect

it to the hard drive.

XTERNAL

3.5”

EVICE

NSTALLATION

There is one external 3.5” drive bay.

1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay.

. Find a pair of 3.5”drive rails in the hardware kit box.

3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on

the outside and facing forward.

4. Slide the device into the drive bay until it clicks into place.

5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive.

XTERNAL

5. 5”

EVICE

NSTALLATION

There are four 5. 5” drive bays and 8 drive rails.

1. Carefully remove the plastic drive bay cover / filter and metal

plate covering the drive bay.

. Mount the drive rails onto the sides of the 5. 5” device. Make

sure the metal portion of the rail faces the front of the drive.

3. Slide the device into the drive bay until it clicks into place.

4. Mount the other devices accordingly.

5. Connect the appropriate Molex or SATA power connector from

the PSU to the power connector on the device.

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative Signal

Positive Signal

Ground

Ke (No Connection)

Empt

Signal

Names

(HDA)

Signal

Names

(AC

’

97)

MIC2

MIC In

AGND

GND

MIC2

MIC Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Ke (no pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

ONNECTING THE

RONT

I/O

ORTS

3.1

USB

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the

motherboard manual to ensure that it matches the table below:

SATA

You will find a SATA connector on a cable attached to the front ports. This internal SATA connector is

designed to connect to a standard SATA connector on your motherboard. This will allow high-speed

external hard disk enclosures such as the Antec MX-1 to run at the same speeds as internally installed

hard disks.

3.3

AC'97

UDIO

ORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)

connector linked to the front panel of the case.

You can connect either the AC’97 or the HDA connector, depending on the model of the motherboard.

Locate the internal audio connectors from your motherboard or sound card and connect the

corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions.

Even if your system supports both audio standards, you may only use one connector.

9 10

3.4

WITCH AND

LED

ONNECTORS

Connected to your front panel are LED and switch leads for power,

reset, and HDD LED activity. Attach these to the corresponding

connectors on your motherboard. Consult your motherboard

manual for specific pin header locations. For LEDs, colored wires

are positive ( + ). White or black wires are negative ( – ). If the LED

does not light up when the system is powered on, try reversing the

connection. For more information on connecting LEDs to your

motherboard, see your motherboard manual.

Note

Polarity (positive and negative) does not matter for switches.

3.5

EWIRING

OTHERBOARD

EADER

ONNECTIONS

There may come a time when you need to reconfigure the pin-out of a motherboard header connector.

Examples could be for your USB header, audio input header, or some other front panel connector such

as the Power Button connector. Before performing any work, please refer to your motherboard manual

or your motherboard manufacturer's website to be sure of the pin-out needed for your connector. We

strongly recommend making a notated drawing before beginning work so that you can recover if your

work gets disturbed.

1. Determine which wires you need to remove inorder to rewire your

plug to match the USB pin-outs on your motherboard (refer to your

motherboard manual). Working on one connector at a time, use

a very small flathead screwdriver or similar tool to lift up on the black

tab located beside the gold posts (squares). This will allow you to

easily slide out the pins from the USB plug.

. Working carefully so as not to damage the wires, connectors, or pins,

slowly remove the pin from the connector. Repeat these steps for

each wire you need to change.

3. Working carefully so as not to damage the wires, connectors or pins,

slowly reinsert the pin into the correct slot of the connector, then

snap closed the black tab that was lifted in Step 1.

Andere Antec Gehäuse Handbücher

Antec

Antec Solution SLK2600AMB User’s Bedienungsanleitung

Antec

Antec Veris Fusion Remote Black Bedienungsanleitung

Antec

Antec Mini P180 White Bedienungsanleitung

Antec

Antec Solution SLK2650-BQE User’s Bedienungsanleitung

Antec

Antec Solution SLK2600AMB User’s Bedienungsanleitung

Antec

Antec NSK6500 Bedienungsanleitung

Antec

Antec UCC13# 0761345-15300-3 NA Bedienungsanleitung

Antec

Antec Solution SLK3700AMB Bedienungsanleitung

Antec

Antec Sonata Bedienungsanleitung

Antec

Antec OVERTURE II Bedienungsanleitung

Antec

Antec NAK3480 Bedienungsanleitung

Antec

Antec 902 Bedienungsanleitung

Antec

Antec Nine Hundred Two Bedienungsanleitung

Antec

Antec VSK-2450 Bedienungsanleitung

Antec

Antec II Bedienungsanleitung

Antec

Antec SX1240 Bedienungsanleitung

Antec

Antec MX-25 Bedienungsanleitung

Antec

Antec SOLO UCC 13# 0761345-08500-7 EU Bedienungsanleitung

Antec

Antec Fusion Remote Max Bedienungsanleitung

Antec

Antec P183 Bedienungsanleitung

Antec

Antec Ruby / Sapphire Bedienungsanleitung

Antec

Antec P190 Bedienungsanleitung

Antec

Antec P160 Bedienungsanleitung

Antec

Antec PLUSView1000 AMG User’s Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Nexans

Nexans WTC05 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung