AOpen AX34II Datenblatt

PS/2 Mouse

Connecto

PS/2 Keyboard

Connecto

USB Port

SPP/EPP/ECP

Parallel Port

COM 1 Port COM 2 Port

MIDI/Game Port

MIC-In

Line-In

Speaker Out

Onboard AC97 CODEC

JP12 Enable/Disable

Onboard Sound

VIDEO-AUDIO-IN Connecto

MODEM-CN Connecto

Front Panel Audio Connecto

AMR Expansion Slot

32-bit PCI Expansion Slot x6

IrDA Connecto

WOM Connecto

2nd USB Connecto

GPO Connecto

2Mb Flash ROM BIOS

WOL Connecto

Dr. LED Connecto

Front Panel Connecto

Chassis Fan

Resettable Fuse

Low ESR Ca

acito

TX Power Connecto

370-pin CPU Socket

with Voltage & Frequency Auto-detection

supports Intel®Pentium®III and Celeron™

300MHz~1GHz+

GP 4X Ex

ansion Slot

VIAApollo Pro 133A Chipset

supports 100/133MHz FSB

168-pin DIMM Slot x4

supports PC100/PC133 SDRAM

maximum up to 1.5GB

JP14 CMOS Clear Jum

FDD Connecto

TA/33/66/100 IDE Connector x2

JP23 & JP29 FSB Select Jumper

CPU Fan

FAN1

CD-IN Connecto

Pin 1

1. JP14 Clear CMOS

2. JP12 Enable/Disable Onboard Audio

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.88904.001 DOC. NO: AX342-EG-E0105B

Hard Drive IDE Cable x 1

80-Wire IDE Cable x 1

Floppy Drive Cable x 1

Bonus Pack CD x 1

Norton AntiVirus CD x 1

This Easy Installation Guide x 1

This motherboard has AC97 sound onboard. JP12 is used to enable or disable onboard AD1885 CODEC

chip. If you don’t want to enable the Onboard Audio, you should set this jumper to 2-3, and disable the

“OnChip Sound” from BIOS setting > Advanced Chipset Features, before you install your preferred PCI

Sound Card.

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pins 1 & pin2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

Normal

(

Default

)

Clear CMOS

Pin 1

Disable

(Default)

Enable

1. Pull up the CPU socket level and up to

90-degree angle.

2. Locate Pin 1 in the socket and look for a

(golden) cut edge on the CPU upper interface.

Match Pin 1 and cut edge. Then insert the

CPU into the socket.

3. Press down the CPU socket level and finish

CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan,

you can also plug it on FAN1 (without H/W monitoring) or FAN2 connector.

5. Setting CPU Voltage & Frequency

4. Installing CPU & Housing Fan

3. Installing CPU

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well, it

may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

GND

+12V

Sensor

Note: Some CPU fans do not have

sensor pin, so that cannot support

fan monitoring.

CPU Fan Connector

FAN1 Connector

GND

+12V

Sensor

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be automatically

detected and the range is from 1.3V to 3.5V. It is not necessary to set CPU Core Voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

Core Frequency = CPU FSB Clock * CPU Ratio

CPU Ratio 2x, 2.5x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x, and 8x

CPU FSB (By BIOS table) 66.8, 68.5, 75, 83.3, 100, 103, 112, 117, 124, 129, 133.3, 138, 143, 148, 150MHz.

CPU FSB

(By manual Adjustment) 66~150MHz by 1MHz stepping adjustment technology

CPU CPU Core Frequency FSB Clock Ratio

Celeron 300A 300MHz 66MHz 4.5x

Celeron 366 366MHz 66MHz 5.5x

Celeron 400 400MHz 66MHz 6x

Celeron 433 433MHz 66MHz 6.5

Celeron 466 466MHz 66MHz 7x

Celeron 500 500MHz 66MHz 7.5x

Celeron 533 533MHz 66MHz 8x

Celeron 566 566MHz 66MHz 8.5x

Celeron 600 600MHz 66MHz 9x

Pentium III 600E 600MHz 100MHz 6x

Pentium III 650E 650MHz 100MHz 6.5x

Pentium III 700E 700MHz 100MHz 7x

Pentium III 750E 750MHz 100MHz 7.5

Pentium III 800E 800MHz 100MHz 8x

Pentium III 850E 850MHz 100MHz 8.5x

Pentium III 533EB 533MHz 133MHz 4x

Pentium III 600EB 600MHz 133MHz 4.5x

Pentium III 667EB 667MHz 133MHz 5x

Pentium III 733EB 733MHz 133MHz 5.5

Pentium III 800EB 800MHz 133MHz 6x

Pentium III 866EB 866MHz 133MHz 6.5

Pentium III 933EB 933MHz 133MHz 7x

Pentium III 1000EB 1GHz 133MHz 7.5x

Tip: If your system hangs or fails to boot

because of overclocking, simply use <Home>

key to restore the default setting (433MHz).

Warning: VIA®Apollo

Pro 133A chipset

supports maximum

133MHz FSB and

66MHz AGP clock,

higher clock setting

may cause serious

system damage.

FAN2 Connector

Pin 1

Secondary

Slave (4th)

Primary

Master (1st)

Primary

Slave (2nd)

Secondary

Master (3rd)

7. Install DIMM Modules

6. JP23 FSB/PCI Clock Ratio 8. Connecting IDE and Floppy Cables

9. Connecting Front Panel Cable

This jumper is used to specify the relationship of PCI and FSB clock. Generally

speaking, if you are not overclockers, we recommend you to set at the default setting.

This motherboard has four 168-pin DIMM sockets that allow you to install PC100 o

PC133 memory up to 2.0GB (or 1.5GB when FSB=133MHz). The AX34 II supports not

only SDRAM but also VCM and Registered DRAM.

Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDD and IDE

connector. The blue connector is IDE1 for clear identification. Be careful of the pin1

orientation. Wrong orientation may cause system damage.

Warning: Higher CPU FSB frequency may be

able to increase CPU speed, but you may damage

the CPU or reduce the CPU lifecycle.

Speaker

IDE LED

SPWR

+ ACPI & PWR

LED

Reset

SPWR

GND

ACPI & PWR LED

GND

+5V

GND

RESET

GND

IDE LED

GND

SPEAKE

ttach the power LED, speaker, and reset switch connectors

to the corresponding pins. If you enable “Suspend Mode” item

in BIOS Setup, the ACPI & Power LED will keep flashing while

the system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug this

connector to the soft-power switch connector marked SPWR.

DIMM1

DIMM2

DIMM3

DIMM4

Auto

(Default)

FSB=133~150MHz FSB=100~124MHz

FSB=66~83MHz

JP23 JP29

Tip: The driving capability of new

generation chipset is limited due to the

lack of a memory buffer (to improve

erformance). This makes DRAM chip

count an important factor to take into

consideration when you install DIMMs.

Unfortunately, there is no way that the

BIOS can identify the correct chip

count; you need to calculate the chip

count by yourself. The simple rule is:

By visual inspection, use only

DIMMs that are less than 18 chips.

ATA 33/66/100 IDE

Connector

FDD Connector

Pin 1

The ATX power supply uses 20-pin connector shown below. Make sure you plug in the

right direction.

12. Connecting CD / MODEM / VIDEO-AUDIO-IN Connector

13. Front Panel Audio

10. Connecting ATX Power Connector

11. Connect IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this

module and application software such as Laplink or Windows 95 Direct Cable

Connection, the user can transfer files to or from laptops, notebooks, PDA devices and

printers. This connector supports HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function

from BIOS Setup, UART mode select, make sure to have the correct orientation when

you plug in the IrDA connector.

If the housing has been design with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

the jumper cap from the Front Panel Audio Connector before you connect the cable. Do

not remove this yellow jumper cap if housing without an audio port on the front panel.

The CD-IN connector is used to connect CD Audio

cable from CDROM or DVD drive to onboard sound.

The MODEM-CN connector is used to connect

Mono In/ Mic Out cable from internal modem card to

onboard sound circuit.

The VIDEO-AUDIO-IN connector is used to connect

MPEG Audio cable from MPEG card to onboard

sound.

VIDEO-AUDIO-IN

(Green)

Connector Pin1 Pin2 Pin3 Pin4

CD-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

VIDEO-AUDIO-IN Left GND GND Right

MODEM-CN

(Red)

CD-IN (Black)

+5V

+3.3V

COM

COM COM

COM

COM COM

-5V

COM

-12V

PS-ON

PW-OK

+12V

5VSB

Pin 1 Pin 1

MIC_IN2

VREFOUT

PHONE_R

PHONE_L

GND

+5V

1 2

9 10

+5V

IRRX

GND

IRTX

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

14. Power-on and Load BIOS Setup

15. AOpen Bonus Pack CD 17. BIOS Upgrade

Open Easy Flash is more use

-friendly than traditional flash method. The BIOS binary

file and flash routine are combined together and you simply run a single file to complete

the flash process.

1. Download new BIOS upgrade zipped file from AOpen's web site. For example,

AX34II102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, AX4II102.BIN & AX34II102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> AX34II102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and you probably need to re-configure your system.

16. Installing Onboard Sound Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

This motherboard comes with an AD 1885 AC97 CODEC, you can find the audio drive

from the Bonus Pack CD disc auto-run menu.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

AX34 II R1.00 Dec. 28. 2000 AOpen Inc.

ward Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AX34 II is model name of motherboard; R1.00 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com.tw/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com.tw/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com.tw/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com.tw/tech/download/default.htm

News Group: Your problem probably had been answered by our support

engineer or professional users on the news group.

http://www.aopen.com.tw/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem more efficien n important reference for

you if next time you want to buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com.tw/tech/contact/techusa.htm

Japanese http://aojp.aopen.com.tw/tech/contact/techjp.htm

Chinese http://w3.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://aofr.aopen.com.tw/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

Open Inc.

Tel: 886-2-2696-1333

Fax: 886-2-8691-2233

merica

Open America Inc.

Tel: 1-510-498-8928

Fax: 1-408-922-2935, 1-408-432-0496

Europe

Open Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

Open Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)

有限公司

Tel: 49-2102-157700

Fax: 49-2102-157799

Andere Handbücher für AX34II

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen MX46S Bedienungsanleitung

AOpen

AOpen i915Ga-HFS Bedienungsanleitung

AOpen

AOpen MX3W Pro Einrichtungshandbuch

AOpen

AOpen MX4B-533 Bedienungsanleitung

AOpen

AOpen MX34 Einrichtungshandbuch

AOpen

AOpen AX4GE Max Einrichtungshandbuch

AOpen

AOpen AX4LR Bedienungsanleitung

AOpen

AOpen MoDT i965GMt-LA Gebrauchsanweisung

AOpen

AOpen MX46U2-GN Einrichtungshandbuch

AOpen

AOpen AX3SP Pro-U Datenblatt

AOpen

AOpen AP53 Bedienungsanleitung

AOpen

AOpen AXPS-U Bedienungsanleitung

AOpen

AOpen ATA Bedienungsanleitung

AOpen

AOpen MX3W-E2 Einrichtungshandbuch

AOpen

AOpen AX45H-8X Max Datenblatt

AOpen

AOpen DX37PU-OL-E0112B Bedienungsanleitung

AOpen

AOpen MX46-800N Datenblatt

AOpen

AOpen MX4SGI-N Einrichtungshandbuch

AOpen

AOpen AX34 Pro II Einrichtungshandbuch

AOpen

AOpen AX4G Pro Bedienungsanleitung

AOpen

AOpen MT85 Bedienungsanleitung

AOpen

AOpen DX34 Plus Bedienungsanleitung

AOpen

AOpen MX64 Bedienungsanleitung

AOpen

AOpen AX4BR-U Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung