Apera Instruments 201-C Bedienungsanleitung

201-C pH Electrode User Manual

Brief Introduction

Apera Instruments 201-C pH Electrode is featured with a proprietary lithium glass membrane for fast

and stable readings. The gel inner reference solution does not need to be refilled. This electrode is

designed for testing in general water solutions. The electrode may NOT work well in the following

situations:

1. Long-term testing in high temperature solutions (>122°F or 50°C)

2. Frequent testing in strong alkaline (>12 pH) or acid (<2 pH) solutions

3. Testing low ionic strength solutions like distilled or deionized water

4. Testing caustic solutions that will corrode the polycarbonate housing of the electrode

Technical Specifications

Range

0 to 14 pH

Housing

Polycarbonate

Junction

Single ceramic

Reference electrode

Ag/AgCl

Reference solution

Gel KCL

Connector

BNC

Cable length

3 Ft

Dimension

ø12*160 mm

Temperature sensor

N/A

Operating temperature

32 to 176°F (0 - 80°C)

How to Install the Electrode

1. Find the BNC socket (where it shows pH ORP) on the pH meter; Open the rubber cap; Insert the

blue BNC connector of the electrode to the BNC socket while twisting clockwise until it’s locked.

2. After installing the new electrode to your meter, a 3-point calibration must be performed to ensure

the accuracy.

How to Use the Electrode

1. There is a proper amount of storage solution in the storage bottle on top of the electrode. The pH

glass sensor tip is soaked in it to keep its sensitivity.

2. Before measuring, loosen the bottle cap, then pull out the electrode while twisting

counterclockwise. Place the storage bottle at a safe position.

3. Rinse the electrode with purified water and shake off excess water or blot-dry it with clean tissue

or filter paper. Never rub the glass membrane.

4. Insert the electrode into your sample solution and stir it for a few seconds in the solution to

remove potential air bubbles, which may cause unstable readings. Then wait for the stable

reading and take the measurement.

5. After use, insert the electrode while twisting clockwise into the storage bottle, then tighten the

bottle cap. If the KCL storage solution (SKU: AI1107) in the cap is contaminated, please fill in new

storage solution (other brands’ storage solution may not work with this electrode).

How to Maintain the Electrode

1. Always rinse the electrode with purified water (distilled or deionized water) before and after each

test and calibration. For general contaminants stuck on the glass bulb sensor, use warm soap

water and a soft brush to clean off; For special contaminants, please refer to the following table

for proper cleaning solutions:

Contaminant

Cleaning Solutions

Inorganic metal oxide

Dilute acid less than 1mol/L

Resin macromolecule

Dilute alcohol, acetone, ether

Proteinic haematocyte sediment

Acidic enzymatic solution (saccharated yeast tablets)

Paints

Dilute bleacher, peroxide

2. Make sure the glass bulb sensor is covered by the KCL storage solution (SKU: AI1107) in the

storage cap when not in use.

3. Never store pH electrodes in pure water such as RO water, tap water, distilled water, or deionized

water as they will cause damage to the electrode.

4. Keep the electrode connector clean and dry. Use cotton balls with isopropyl alcohol to clean if it

gets dirty and then blow-dry it. This is to prevent a potential short circuit, which will undermine the

electrode’s performance.

5. pH electrodes do not last forever. They age through normal use and eventually will fail. The

regular service life of the pH electrode is 1-2 years. If you feel like the response of your pH

electrode is becoming unusually slow, or the slope is lower than 90% (most Apera

portable/benchtop pH meters will show the slope data between every two points of calibration),

it’s time to replace with a new electrode to ensure accuracy.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agree to repair or

replace free of charge, at the option of APERA INSTRUMENTS any malfunctioned or damaged product

attributable to responsibility of APERA INSTRUMENTS for a period of SIX MONTHS from the delivery.

This warranty does not cover any damages due to:

Accidental damage, transportation, storage, improper use, failure to follow the product instructions,

unauthorized repair, normal wear and tear, or any other actions or events beyond our reasonable

control.

APERA INSTRUMENTS (Europe) GmbH | Wilhelm-Muthmann-Str.15, 42329 Wuppertal, Germany

info@aperainst.de | www.aperainst.de | Tel.: +49 202 51988998

Inhaltsverzeichnis

Andere Apera Instruments Messgerät Handbücher

Apera Instruments

Apera Instruments EC700 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 851-H Bedienungsanleitung

Apera Instruments

Apera Instruments SX731 Bedienungsanleitung

Apera Instruments

Apera Instruments EC400 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 551 Bedienungsanleitung

Apera Instruments

Apera Instruments 950 Series Bedienungsanleitung

Apera Instruments

Apera Instruments SX725 Bedienungsanleitung

Apera Instruments

Apera Instruments TN420 Bedienungsanleitung

Apera Instruments

Apera Instruments SX823-B Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 821 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 851-1 Bedienungsanleitung

Apera Instruments

Apera Instruments WS200 Bedienungsanleitung

Apera Instruments

Apera Instruments PC 850 Bedienungsanleitung

Apera Instruments

Apera Instruments DO8500 Bedienungsanleitung

Apera Instruments

Apera Instruments WS100 Bedienungsanleitung

Apera Instruments

Apera Instruments TN480 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 211 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 753 Bedienungsanleitung

Apera Instruments

Apera Instruments Gro Star AI102G Bedienungsanleitung

Apera Instruments

Apera Instruments SX811-BS Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 763 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 751 Bedienungsanleitung

Apera Instruments

Apera Instruments PH60-WW Bedienungsanleitung

Apera Instruments

Apera Instruments PH400 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung