Apollo PEX 69PTKH00143 Betriebsanleitung
Matthews, NC 28105
www.apolloow.com
69PTKH-I_12/1/11
69PTKH00143; 69PTKH00144;69PTKH00185
69PTKH0014C; 69PTKH0015K
PEX Crimp Tool
How to use:
123
4
1
For 69PTKH0015K
To remove and replace crimp heads:
1. Cut tubing end squarely.
Check for and remove any
burrs.
2. Slide crimp ring over end
of tubing. Insert tting into
end of tubing until it stops.
Position the crimp ring
1/8"to 1/4"from the end
of the tubing and over the
ribs of the tting.
3. Place the crimping end of
tool around the crimp ring
and press the handles
together.
4. Check for proper crimp
with the Go/ No-Go
gauge.
1. With the handles.
fully open, press
side release spring
upward until the
hook is above the
jaw pin.
3. With the side
release spring
pressed upward,
slide new jaw into
place and release
the spring.
2. Slide jaw out of
position and
remove.
2 3
Matthews, NC 28105
www.apolloow.com
69PTKH-I_07/10/14
69PTKH00143; 69PTKH00144;69PTKH00185
69PTKH0014C; 69PTKH0015K
1. Slide the correct slot
on the gauge around
the crimped ring.
2. If the ring does not t
into the slot at all, then
the crimp is a “No-Go”.
Adjust the crimping force
on the tool and re-crimp
the ring.
3. If the ring slides into the
slot and stops in the
“Go” range, then the
crimp is good.
4. If the ring slides all the
way into the slot,
then the crimp ring is
compressed too small
and is a “No-Go”.
Remove the ring and
adjust the crimping force
on the tool.
PEX Go/No-Go Gauge
How to use:
1. Open the handle, then
loosen the nut on the
screw with the
numbers surrounding
it.
2. Push and rotate the
screw. Increase the
number for more crimp
force. Decrease the
number for less crimp
force.
3. Push the screw back
into place and tighten
the nut.
How to adjust the crimp force:
If your crimp tool has screws on
the side, to adjust the crimp force
rst loosen the set screw. Next,
tighten the adjustment screw for
more force or loosen the screw for
less force. Finally, tighten the set
screw after any adjustments.
Illustration of a good connection:
1. Fitting shoulder location.
2. Pipe is cut square and stops at tting sholder.
3. Position the CrimpRing 1/8"- 1/4"from the end of the pipe, directly over
two end ribs of the tting.
4. The CrimpRing is evenly compressed over the pipe and shows no
evidence of uneven distortion.
5. The PEX material is uniformly compressed between the ribs, resulting in
a leak-free, quality joint.
Dieses Handbuch passt für folgende Modelle
4
Andere Apollo Crimpwerkzeuge Handbücher
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Milwaukee
Milwaukee M18 Bedienungsanleitung
HOGERT
HOGERT HT1P169 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung