Tyco Electronics 90035-3 Bedienungsanleitung
Instruction Sheet
411-3236
LOC B
1
of 5
E
2009 Tyco Electronics Corporation, Harrisburg, A
All International Rights Reserved
AM , TE logo, and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
RODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
22 JAN 09 Rev A
Hand Crimping Tool 90035-3
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Figure 1
Terminal
Locator
Crimping
Jaws
Back of Tool
(Wire Side)
Wire Size
Marked
Here
Insulation
Adjustment
ins in No. 3
osition
Tool Number
Marked Here
CERTI-CRIM *
Hand Crimping
Tool Ratchet
Control
1. INTRODUCTION
Hand Crimping Tool 90035–3 has been designed for
crimping the PIDG* FASTON* loose piece (LP)
receptacle terminals listed in Figure 2. Read these
instructions thoroughly before crimping any terminals.
All dime sio s i this docume t are i millimeters
[with i ches i brackets]. Figures a d Illustratio s
are for refere ce o ly a d are ot draw to scale.
Reasons for reissue are provided in Section 6,
REVISION SUMMARY.
2. DESCRIPTION
(Figure 1)
The FRONT OF TOOL has the “AMP” marking on the
link. The BACK OF TOOL (Wire Side), into which the
wire is inserted, has the wire size marked on the link.
This tool features a terminal locator, two insulation
adjustment pins, and a CERTI–CRIMP hand crimping
tool ratchet control. The locator is spring–loaded to
position and hold the terminal in the tool.
The insulation adjustment pins are used to regulate
the crimp height of the terminal insulation barrel. See
Paragraph 3.2. The CERTI–CRIMP hand crimping
tool ratchet control ensures full crimping of the
terminal. Once engaged, the ratchet will not release
until the tool handles have been FULLY closed.
The crimpi g jaws bottom before the
CERTI-CRIMP ha d crimpi g tool ratchet co trol
releases. This is a desig feature that e sures
maximum electrical a d te sio performa ce of
the crimp. Do NOT re-adjust the ratchet.
NOTE:
Not to Scale
Wire Strip Length
Receptacle
Terminal
Locator
Slot
Wire
Barrel
Insulation
Barrel
WIRE SI E
(AWG) INSUL. DIA.
(Max) TERMINAL
NO. WIRE STRIP
LENGTH
22-18 3.43 [.135]
42599-[ ]
140879-[ ]
140896-2
140948-1
735278-[ ]
5.56 [.219]
Figure 2
NOTE
i
CAUTION
!
411-3236
Hand Cr mp ng Tool 90035-3
Rev
A2
of 5 Tyco Elec ronics Corpora ion
3. CRIMPING PROCEDURE
Refer to the table in Figure 2 and check the selected
wire, terminal, and crimping tool for compatibility. Wire
size and insulation diameter must be within the
specified range for the terminal. The hand crimping
tool must be the one designed for crimping the wire
and terminal.
Use stranded wire only, and strip it to the length
indicated. Refer to Figure 3 and proceed as follows:
Do NOT cut or nick the wire strands.
Figure 3
Opened Por ion
of Recep acle
Slo in
Loca or
Loca or
Base Press Here o
Raise Loca or
Insula ing Sleeve
Bu s Agains Loca or
Back of Tool
(Wire Side)
3.1. Term nat on Procedure
1. Hold tool so the BACK (Wire Side) is facing you.
2. Make sure the ratchet is released. Squeeze tool
handles together and allow them to open FULLY.
3. Raise the locator and insert the terminal into the
slot, making sure the opened portion of the
receptacle is turned away from the locator base
4. Position the terminal so the insulation sleeve
butts against the locator and is centered on the
crimping jaws.
5. Insert a properly stripped wire into the terminal
until the wire insulation begins to wedge against
the terminal insulation barrel, or until the wire
insulation butts against the terminal wire barrel.
Wire end should be approximately flush with the
wire barrel end.
6. Holding the wire in place, squeeze the tool
handles together until the ratchet releases.
7. Allow the tool handles to open FULLY. Raise the
locator and remove the crimped terminal from tool.
3.2. Insulat on Cr mp Adjustment
The insulation barrel crimp height is regulated by
placing the insulation adjustment pins in one of three
positions (1–Small, 2–Medium, 3–Large). Determine
the proper insulation crimp setting as follows:
1. Place adjustment pins in No. 3 position. Insert
terminal into the tool according to Paragraph 3.1,
Steps 1 through 4.
2. Insert an unstripped wire into the terminal
insulation barrel. Crimp the terminal and remove it
from the tool.
3. Check the insulation crimp by bending the wire
back and forth one time. If the wire pulls out, place
the adjustment pins in the next smaller position,
and repeat these procedures. The crimp should
hold the wire insulation firmly without cutting into it.
4. MAINTENANCE AND INSPECTION
Hand crimping tools are inspected before shipment.
The tool received should be inspected immediately
upon arrival to ensure that the tool has not been
damaged during shipment, and that it performs
according to the criteria described in this sheet. If a
tool is damaged upon arrival, retain the shipping
container, file a claim with the carrier, and notify Tyco
Electronics immediately.
4.1. Da ly Ma ntenance
1. Remove dust, moisture, and other contaminants
from the tool with a clean brush or a soft, lint–free
cloth. DO NOT use objects that could damage the
tool.
2. Make sure that the proper retaining pins are in
place and are secured with the proper retaining
rings.
3. Make certain that all pins, pivot points, and
bearing surfaces are protected with a THIN coat of
any good SAE 20 motor oil. DO NOT oil
excessively.
4. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged in
the crimping areas and store the tool in a clean,
dry area.
4.2. Per od c Inspect on
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool or be supplied to
supervisory personnel responsible for the tool.
CAUTION
!
411-3236
Hand Crimping Tool 90035-3
3
of 5Rev
A
Tyco Electronics Corporation
Though recommendations call for at least one
inspection per month, the inspection frequency should
be based on the amount of use, working conditions,
operator training and skill, and established company
standards. These inspections should be performed in
the following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) in a
suitable commercial degreaser that will not affect
paint or plastic material.
2. Make certain that all retaining pins are in place
and are secured with retaining rings. If
replacements are necessary, refer to the parts list
in Figure 6.
3. Inspect crimping areas for pitted or chipped
surfaces.
4. Close the tool handles until the ratchet releases,
then allow handles to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced. Refer to Section 5,
REPLACEMENT AND REPAIR.
B. Gaging Crimping Cham er
This inspection requires the use of plug gages
conforming to the dimensions listed in Figure 4. To
gage the crimping chamber, proceed as follows:
1. Close the jaws by squeezing the tool handles
together until the jaws have bottomed, and then
HOLD the handles in this position. DO NOT force
the jaws beyond initial contact.
2. Align the GO element of the gage with the wire
barrel crimp section of the crimping chamber. Refer
to Figure 5. Push the element straight into the
crimping chamber without using force. The GO
element must pass completely through the
crimping chamber.
3. Align the NO–GO element of the gage with the
same crimp section, and try to insert the element.
The NO–GO element may start entry, but it must
not pass completely through the crimping chamber.
Refer to Figure 5.
4. Repeat the gage inspection for the insulation
crimp section of the crimping chamber, making
sure to use the correct plug gage.
If the crimping chamber conforms to the gage
inspection, the tool is considered dimensionally
correct. If the crimping chamber does not conform to
the inspection, the tool must be repaired. Refer to
Section 5, REPLACEMENT AND REPAIR.
For additional information concerning the use of the
plug gage, refer to Instruction Sheet 408–7424.
C. Ratchet Inspection
Obtain a .025–mm [.001–in.] shim that is suitable for
checking the clearance between the bottoming
surfaces of the jaws. To inspect the ratchet control,
proceed as follows:
1. Refer to Figure 2, and select a product and
maximum size wire.
2. Position the product in the crimping chamber.
3. While holding the wire in place, squeeze the tool
handles together until the ratchet releases. Holding
the tool in this position, maintain just enough
pressure to keep the jaws closed.
4. Check the clearance between the bottoming
surfaces of the jaws. If the clearance is .025 mm
[.001 in.] or less, the ratchet is satisfactory. If
clearance exceeds .025 mm [.001 in.], the ratchet
is out of adjustment and must be repaired. Refer to
Section 5, REPLACEMENT AND REPAIR. If the
tool conforms to this inspection procedure,
lubricate it with a THIN coat of any good SAE 20
motor oil, and return it to service.
5. REPLACEMENT AND REPAIR
Customer–replaceable parts are listed in Figure 6.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts
through your representative, or call 1–800–526–5142,
or send a facsimile of your purchase order to
717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105–3608
For customer repair service, call 1–800–526–5136.
6. REVISION SUMMARY
S
Updated document to corporate requirements
S
Added new Sections 4 through 6
S
Added new Figures 4, 5, and 6
411-3236
Hand Crimping Tool 90035-3
Rev
A4
of 5 yco Electronics Corporation
Jaw Closure
Configuration
50.8 [2.00]
Min yp
Suggested Plug Gage Design Ċ Wire Barrel Crimp Section
A
B
(NO-GO)
B
(GO)
4A
TOOL
JA CLOSURE
{
DIAMETER A GAGE ELEMENT
{{
DIAMETER B
TOOL
GO NO-GO GO NO-GO
90035-3 2.350 [.0925] 2.477 [.0975] 2.350-2.357
[.0925-.0928] 2.474-2.477
[.0974-.0975]
Suggested Plug Gage Design Ċ Insulation Barrel Crimp Section
G (NO-GO)
W (Max)
GO NO
GO
6.35 [.250] yp
Jaw Closure
Configuration
G (GO)
F
4
B
TOOL
JA CLOSURE
{
DIMENSION F
(Adjustment Pins in Position 1) GAGE ELEMENT
{{
DIMENSION G DIMENSION
( idth)
GO NO-GO GO NO-GO
( idth)
90035-3 0.762 [.0300] 1.27 [.0500] 0.762-0.77
[.0300-.0303] 1.267-1.27
[.0499-.0500] 3.05 [.120]
{
Jaw closure dimensions apply when wire or insulation barrel jaws are bottomed, but not under pressure.
{{
Material: ool Steel
Figure 4
Figure 5
GO Element Must Pass
Completely hrough Jaw Closure
NO-GO Element May Enter
Partially, But Must Not Pass
Completely hrough Jaw Closure
Inspection of Wire Barrel Crimp Section Inspection of Insulation Barrel Crimp Section
Jaws Bottomed But
Not Under Pressure
Insulation Crimp
Adjustment Pins in
Position 1 (Ref)
Wire Barrel
Crimp Section of
Crimping Chamber Insulation Barrel
Crimp Section of
Crimping Chamber
411-3236
Hand Cr mp ng Tool 90035-3
5
of 5Rev
A
Tyco Electronics Corporation
9
4
32
1
8
7
10 622.2 [.875]
280 [11.0]
76 [3.0]
(Closed)
5
Weight: 550g [1.2 lb]
ITEM NUMBER PART NUMBER DESCRIPTION QTY PER TOOL
1 21045-3 RING, Retaining 4
2 1-23619-6 PIN, Retaining (.187D x .521L) 2
3 21045-6 RING, Retaining 2
4 2-23620-9 PIN, Retaining [250D x .838L) 1
5 39364 PRING, Handle 1
6 39207 IN ULATION ADJU TMENT PIN 2
7 125644-4 LOCATOR 1
8 302994 HOU ING, Locator 1
9 301201 PRING 1
10 9-305927-1 CREW 1
Figure 6
Inhaltsverzeichnis
Andere Tyco Electronics Crimpwerkzeuge Handbücher
Tyco Electronics
Tyco Electronics PRO CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics 696675-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 1901820-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics 46073 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics 58425 Series Bedienungsanleitung
Tyco Electronics
Tyco Electronics SIMEL Autocoup CC040 Cof. + charg. Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58564-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics AMP CERTI-CRIMP II Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III 58603-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 46121 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PIDG STRATO-THERM Bedienungsanleitung
Tyco Electronics
Tyco Electronics 2063195-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Textron
Textron ESG105L Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 105CFB Bedienungsanleitung
TE Connectivity
TE Connectivity 539 726-2 Bedienungsanleitung