Arbor Technology Double Bay Bedienungsanleitung

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Generic build instructions –Double Bay log store

Before you commence the assembly process, we recommend that you read these

instructions thoroughly beforehand to familiarise yourself with the assembly process and to

also check that you have the correct components.

We highly recommend that any assembly is carried out on a flat, level surface if possible

and that you use another person to assist you if necessary.

You can check our YouTube channel for assemble video, click on the link below:

Double Bay wooden log store - assembly video

Package contents:

2x Side panels

2x Back panels

2x Centre posts

1x Base

1x Lattice

1x Roof

65mm screws

6x 85mm screws (for the base only)

2x Spacer blocks

Tools required:

Electric screwdriver (No.2 Pozi bit) or

Screwdriver

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Arrange the 2 spacer blocks on the ground

(the orientation is not critical), adjacent to

the end panel as shown in the photo above.

Now place a back panel on the blocks, at 90°

to the end panel, aligning the 2 panels ready

for fixing.

Using the 65mm screws provided, attach the

batten on the back panel to the post of the

end panel, ensuring that the batten remains

vertically aligned to the post.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Ensure that you have all the correct parts as

listed on the front page of these instructions,

including any fixings.

Stand the left-hand end panel (or right hand for

the reversed roof version) upright on a flat, level

surface.

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Align one of the longer posts (shorter for a

reversed roof) with the other end of the back

panel.

Attach the panel to the post by screwing

through the batten using 65mm screws as

before.

Rearrange the spacer blocks and offer up the

next panel, aligning and attaching it as before.

Remove the blocks from beneath the 2nd panel

and then slide the base into position as shown,

ensuring that the centre post and the central

cross member of the base are aligned in the

middle of the back assembly.

Step 7

Step 8

Step 9

Step 10

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Slide the remaining end panel into place as shown

above and attach it to the frame as you did with the

first end panel with 85mm screws into the front and

rear posts. If you are fitting a kindling shelf, omit

steps 12 -14 and attach the front posts before fitting

the kindling shelf & lattice and then attaching the

roof.

Carefully place the roof on top of the log store.

Step 11

Step 12

Step 13

Step 14

Attach the base to the end panel front post first,

using 1 of the 85mm screw and then secure the

rear post in the same way.

Using more of the 85mm screws now attach the

base to the rear posts as shown.

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Check that the batten ends sit flush with the posts

as shown. Now attach the roof to each end panel

post with 65mm screws.

Secure the rear of the roof using 65mm screws as

shown.

Sit the lattice in the store so that it is leaning

against the back panel as shown above, so that

you have enough clearance to attach the front

posts as shown in the next step.

Fit a central post into the slotted roof position.

By measuring the distance from the side panel

to the central post and making sure it is equal at

the bottom and the top. (The space from the

side panel to the central post must be equal to

the back panels measurements).

Step 15

Step 16

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 17

Step 18

Step 19

Step 20

Make sure that the centre post sits flush

with the roofs batten ends and secure in

place with 1 of the 65mm screws.

After making sure that the gap at the bottom is

the same as in the top attach the centre post to

the base panel with the provided 1x 80mm

screw.

Your Double Bay log store is now complete.

If you are fitting doors, please proceed with

step 20 hinge to the post.

Place a spacer block at the front of the log

store adjacent to the front-end post and rest

the hinge side of the appropriate door on

the block, aligning it vertically and

horizontally for a good fit. Now use four of

the supplied black hinge screws to affix the

hinge to the post.

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Fit the hook to the opposite side of the doors from the hinges to whichever

height is the best for you with 2x black screws. Don’t forget to attach the

provided batten to the other side of the doors while screwing in the black

screws to hide the pointy screw end’s sticking out of the doors.

To fit the latch keeper plate, shut the

door and hold the latch in the

horizontal position. Now fit the

keeper and mark its correct fixing

position on the post using a pencil or

bradawl before securing it in place

using the screws provided.

Step 21

Step 22

Step 23

Step 24

Align the top hinge in place, ensuring that

the gap between the door and post is

consistent at top and bottom.

Secure the top hinge in place using more of

the black hinge screws. Repeat steps 20 - 22

for any further doors as required.

01945 410950 support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Your double bay log store is now completed!

We hope that you found your product quick and easy to assemble but if not and you require further

assistance or have any questions you can contact us via details above.

Also, you can check our YouTube channel for assemble videos, click on the link below:

https://www.youtube.com/channel/UC3b2MzAv6fTkCPnC3QF7V9w

Or type in YouTube search box Arbor Garden Solutions.

Andere Arbor Technology Außenlagerung Handbücher

Arbor Technology

Arbor Technology Triple Bay Log Store Handbuch

Arbor Technology

Arbor Technology Triple Wheelie Bin Storage Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Duratuf

Duratuf GL105 Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

Duratuf

Duratuf Havelock Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Duratuf

Duratuf Kiwi MK1 Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung