Arecont Vision MegaDome AV1355DN-1HK Bedienungsanleitung

Arecont Vision MegaDome®Installation Manual

0 | P a g e

Arecont Vision MegaDome®Installation Manual

1 | P a g e

MegaDome®Installation Manual

Inside the box:

A. Arecont Vision MegaDome®

B. Mounting template

C. Magnetic core

D. Pack of four (4) wood screws and four (4)

dry wall anchors

E. One double sided hex key

F. One single sided hex key

G. Security L-key

H. Power cable

Not included but needed:

#1 Phillips head screw driver

#2 Phillips head screw driver

Image 1

Mounting the Camera:

1. Remove camera and hardware from the

box.

2. Using the Mounting template, prepare the

mounting provisions for camera

installation. NOTE: the 19.5mm diameter

hole on the Mounting template is where

the Ethernet cable will be exiting the

MegaDome®, align accordingly. If using

the side conduit hole, please see step 9

below.

3. Using Security L-key, loosen the four (4)

screws securing the dome cover (Image

2). Remove vandal resistant dome

cover. NOTE: Do not remove screws

from the dome cover.

Image 2

RJ-45

POWER

HOLE

Arecont Vision MegaDome®Installation Manual

2 | P a g e

4. Run Ethernet cable through the hole on the

bottom of the camera (Image 3) and plug it

into the RJ45 port. NOTE: If the camera will

be powered via PoE, please skip to step 6.

5. If the camera is powered by an outside power

supply, run the supplied power cable through

the hole and connect it to its respective

connector inside the camera (Image 3).

NOTE: Make sure that your installation of

wires complies with Electrical Code of the

local government where the camera is

installed and no bare wires are exposed.

6. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera to the mounting surface

with the wood screws or any optional

hardware suitable for the mounting surface.

7. Install the included magnetic core onto the

Ethernet cable as shown in Image 4. NOTE:

Ensure both tabs are tightly secured.

Image 3

Image 4

HOLE

POWER

RJ-45

Arecont Vision MegaDome®Installation Manual

3 | P a g e

8. Reference Image 5 for proper positioning of

the magnetic core.

9. If you are using the side conduit opening,

remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys (Image 6).

Image 5

Image 6

Adjusting the Tilt, Pan, Z-axis (yaw) and Focus:

10. To adjust the tilt, use a #1 Phillips screwdriver

to loosen the screw on the side of the plastic

lens bracket 1/4 turn (Image 7). CAUTION:

Do not remove the screw!

11. Adjust lens tilt as required and tighten the

screw from step 10.

12. To adjust the pan, use a #2 Phillips

screwdriver to loosen the screw as shown in

Image 7.

13. Adjust the pan as required and tighten the

screw from step 2.

14. To adjust the Z-Axis, or Yaw, for vertical wall

mounting, loosen the set screw as shown in

Image 7. NOTE: There are two set screws on

opposite sides; both need to be loosened.

15. Adjust the Z-Axis as required and tighten the

set screw back down.

Image 7

Z-AXIS

(yaw)

TILT

PAN

Arecont Vision MegaDome®Installation Manual

4 | P a g e

16. To adjust back focus, loosen the two (2) set

screws with the appropriate Allen key as

shown Image 8 (only one of two screw holes

shown). Adjust the silver back focus ring as

needed and tighten down the set screws.

17. To focus the lens, loosen the three set screws

as shown in Image 9 and adjust each as

needed. Aadjusts the zoom, Badjusts the

iris (adjustment is the band between A and C

as outlined in red; there is no set screw), C

adjusts the focus.

18. Remove the protective film from the camera

dome. NOTE: be cautious not to scratch the

vandal dome cover.

19. Secure the vandal dome cover to the camera.

Image 8

Image 9

BACK

FOCUS

SET

SCREW

BACK

FOCUS

RING

BACK

FOCUS

SET

SCREW

BACK

FOCUS

RING

Arecont Vision MegaDome®Installation Manual

5 | P a g e

Installation Best Practices

Begin Installation

Wind Vinyl electrical

tape on all cables

Adding Teflon thread sealing

tape to all male threads

Connect ¾” NPT conduit pipe

to junction box adapter

Does conduit pipe go through the wall?

Make sure position of conduit

hole is at the lower side

forming a “drip loop” below

the camera using ¾”

galvanized or flex conduit and

appropriate fittings

Not Recommended!

Recommended!

Yes

Tighten all camera screws

and ¾” NPT plugs

Caulk the perimeter of the mounting area

Conduct periodic inspections of the installation. Rust

on the metal parts or screws may result in damage to

camera

End Installation

Arecont Vision MegaDome®Installation Manual

5 | P a g e

MegaDome®Pendant Mount (MD-CMT) Installation Instructions

Inside the box:

A. Top shield

B. Pendant Mount

C. Mounting template

D. Pack of four (4) machine screws

E. Pack of four (4) small machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

G. Large round rubber gasket

H. Smaller square rubber gasket

I. One double sided hex key

Not included but needed:

J. #2 Phillips head screw driver

Image 10

20.Remove Pendant Mount and hardware from

the box.

Image 11 Image 12

21. Using the Mounting template, prepare the

mounting provisions for camera installation.

22. Place small gasket onto pendant dome as

shown in image 11.

23. Attach Dome to Pendant as shown in Image

12 using four machine screws provided.

24. Install large round rubber gasket onto

Pendant as shown in image 12. Be sure to

align the holes appropriately.

25. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

26. Attach Pendant to the ceiling using the four

wood screws provided or any optional

hardware suitable for the mounting surface.

27. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision MegaDome®Installation Manual

6 | P a g e

MegaDome® Wall Mount (MD-WMT2) Installation Instructions

Inside the box:

A. Wall mount

B. Top shield

C. Mounting template

D. One double sided hex key

E. Pack of four (4) machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

Not included but needed:

#2 Phillips head screw driver

Image 13

28. Remove Wall Mount and hardware from the

box.

Image 14

29. Using the Mounting template, prepare the

mounting surface.

30. Install Top Shield on Wall Mount as shown in

image 14.

31. Fasten the socket set screw using double side

hex key.

32. Run Ethernet Cable and outside power cable

(if necessary) through the Wall Mount.

33. Attach Wall Mount to the wall using drywall

screws or any optional hardware suitable for

the mounting surface.

34. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision MegaDome®Installation Manual

7 | P a g e

MegaDome®Wall Mount Cap (MD-CAP) Installation Instructions

Inside the box:

A. Wall Mount Cap (MD-CAP)

B. Pack of four (4) machine screws

Not included but needed:

1½” NPT Pipe nipple

1½” NPT Coupling

1½” NPT Flange

#2 Phillips head screw driver

Image 15

35. Remove Wall Mount Cap from the box.

36. Assemble Wall Mount Cap, 1½” Coupling,

1½” Pipe nipple and 1½” Flange as a Pendant

Mount shown in image 16.

Image 16

37. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

38. Attach Pendant to the ceiling using four wood

screws or any optional hardware suitable for

the mounting surface

39. For installation of the camera, please

reference “Mounting the Camera”.

MD-CAP

1 ½” Coupling

1 ½” Pipe

1 ½” Flange

Arecont Vision MegaDome®Installation Manual

8 | P a g e

MegaDome®Junction Box Adapter (MD-JBA) Installation Instructions

Inside the box:

A. Junction Box Adapter

B. Pack of four (4) machine screws

C. Pack of four (4) wood screws and four (4)

dry wall anchors

D. Large round rubber gasket

E. One double sided hex key

Not included but needed:

#2 Phillips head screw driver

MegaDome® Wall Mount, MD-WMT

¾” NPT Conduit (if necessary)

Image 17

40. Remove Junction Box and hardware from the

box

Image 18 Image 19

41. Remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys shown in Image 18.

42. Attach Junction Box Adapter to the wall using

drywall screws or any optional hardware

suitable for the mounting surface.

43. Attach MegaDome® Wall Mount to Junction

Box Adapter as shown in Image 19.

44. Connect ¾” NPT Conduit to Junction Box

Adapter

45. Run Ethernet Cable and outside power cable

(if necessary) through the Junction Box

Adapter and Wall Mount.

46. For installation of the camera, please

reference “Mounting the Camera”.

Inhaltsverzeichnis

Andere Arecont Vision Sicherheitskamera Handbücher

Arecont Vision

Arecont Vision AV2225PMIR Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Bedienungsanleitung

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-NL Bedienungsanleitung

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall 2 Bedienungsanleitung

Arecont Vision

Arecont Vision MicroDome AV1455DN-F Bedienungsanleitung

Arecont Vision

Arecont Vision AV2100 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaVideo Flex Series Bedienungsanleitung

Arecont Vision

Arecont Vision MegaView v1x series Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Bedienungsanleitung

Arecont Vision

Arecont Vision MicroDome AV2455DN-S Bedienungsanleitung

Arecont Vision

Arecont Vision Contera Micro Bullet Bedienungsanleitung

Arecont Vision

Arecont Vision H.264 Day/Night SurroundVideo Series Bedienungsanleitung

Arecont Vision

Arecont Vision AV12275DN-NL Bedienungsanleitung

Arecont Vision

Arecont Vision Megaball series Bedienungsanleitung

Arecont Vision

Arecont Vision MicroDome G2 AV1555DN-S Bedienungsanleitung

Arecont Vision

Arecont Vision D4S Series Bedienungsanleitung

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-08 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaDome G3 Bedienungsanleitung

Arecont Vision

Arecont Vision SurroundVideo G5 Mini Bedienungsanleitung

Arecont Vision

Arecont Vision MegaDome 2 Bedienungsanleitung

Arecont Vision

Arecont Vision AV1215PM-S Bedienungsanleitung

Arecont Vision

Arecont Vision Contera AV02CLB-100 Bedienungsanleitung

Arecont Vision

Arecont Vision D4SO Series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung