Argos Camden 305/0741 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 117cm

Depth - 49.5cm

Height - 183.5cm

Camden - 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 12/12/12

Important - Please read these instructions fully before starting assembly

Ruler - Use this ruler to help correctly identify the screws

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

305/0741

305/0758

ALR2832

Issue 2 - 12/12/12 - Changed the assembly method so that the Left Side is fitted after the Large Back Rail has been fitted.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 67kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

1 2

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Hanging Rail (FHR343)

(343mm long)

Hanging Rail (FHR715)

(715mm long)

Upright (D2011A)

(1688 x 472mm)

Base (D2010A)

(1090 x 473mm)

Plinth (D2012A)

(1090 x 96mm) 10

Top (D2009a)

(1166 x 492mm)

Foldy Back (X733)

(1713 x 740mm)

Back (X734)

(1713 x 363mm)

Door (D2008A)

(1700 x 358mm) x 3

Left Side (D2004A)

(1800 x 491mm)

Right Side (D2005A)

(1800 x 491mm)

Large Back Rail (D2014A)

(725.5 x 130mm)

Small Back Rail (D2013A)

(349.5 x 130mm)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

ScissorsSquare

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step

ladder

Ruler - Use this ruler to help correctly identify the screws

40mm Screw (F910) x 2

B C

D E F

G H I

Nail (F51) x 38

LHinge plate

(F523) x 9

Rail Holder

(F891) x 4 13mm Screw (F63) x 26

Hollow core

locking nut

(F892) x 4

Small metal dowel

(F893) x 4

19mm Screw (F461) x 6

Metal dowel (F901) x 10

Large locking

nut (F900) x 12

Hinge (F522) x 9

Wooden dowel (F22) x 10

J K

13mm Screw (F79) x 13

Bracket (F327) x 1

Electric drill

(only use

when drilling

into walls)

Handle (F309) x 3

Double metal dowel (F566) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the upright

a: Tap 2 wooden

dowels into the ends

of the upright .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

To fit the rail holder ,

screw through the top

hole with screw and

into the mark hole drilled

in the upright . Make

sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

Turn upright panel over

80%

x3 3

Finished

front edge

Turn the upright over

Finished

front edge

10mm

b: Fit 3 hinge plates

onto the upright ,

making sure that the slot

is facing towards the

finished front edge.

To fit the rail holder ,

screw through the top

hole with screw and

into the mark hole drilled

in the upright . Make

sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

Insert 2 large locking

nuts into the upright.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Assembly Instructions

Step 2

Prepare the top

Screw 4 small metal

dowels into the holes

on the top .

Screw 2 metal

dowels into the holes

on the top .

Note: Tighten metal

dowels up fully against

the panels.

Step 3

Prepare the base

Insert 4 large locking

nuts into the base

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Tap 2 wooden dowels

into the ends of the base

. .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Step 4

Prepare the small

back rail

Insert 2 large locking

nuts into the small

back rail .

Tap 2 wooden dowels

into the small back rail .

10mm

Finished

front edge

Assembly Instructions

Step 5

Fit base to right side

Push the base onto

the right side as

shown.

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 4

Finished

front edge

Finished

front edge

Fit base to the upright

Push base onto the

upright and secure

using 2 screws .

Fit the top

Push the top onto

the upright .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the upright .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 6

Assembly Instructions

Step 7

a: b:

B B

Prepare the right side

a: Fit 3 hinge plates

onto the right side ,

making sure that the slot

is facing towards the

finished front edge.

b: To fit the rail holder

. , screw through the

top hole with screw

and into the mark hole

drilled in the right side

. . Make sure that it is

fitted straight, in line with

the panel edges and

then fit another screw

using the lower hole.

c: Push 2 hollow core

locking nuts into the

right side , making

sure that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

d: Screw 4 metal

dowels into the holes

on the right side .

Note: Tighten metal

dowels up fully against

the panel.

Finished

front edge

Assembly Instructions

Step 8Step 7

Fit the right side to

the assembly

Push the right side

onto the top .

Note: You will need to

make sure that the 2

small metal dowels

fitted to the top , slide

into the top of the 2

hollow core locking nuts

. fitted to the right

side .

Insert a

screwdriver

into the 2

hollow core

locking nuts

. and turn

the nuts

inside as far

as they will go.

B B

Fit the small back rail

Push the small back rail

. onto the right side

and upright .

Use a screwdriver to

tighten the large locking

nut on the small back

rail .

Use a screwdriver to

tighten the 2 large

locking nuts on the

base .

Step 9

Assembly Instructions

Step 10

Prepare the left side

a: Fit 3 hinge plates

onto the left side ,

making sure that the slot

is facing towards the

finished front edge.

b: To fit the rail holder

. , screw through the

top hole with screw

and into the mark hole

drilled in the left side .

Make sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

c: Push 2 hollow core

locking nuts into the

left side , making sure

that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

d: Screw 4 metal

dowels into the holes

on the left side .

Note: Tighten metal

dowels up fully against

the panel.

B B

b: F

Finished

front edge

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos 832/9408 Bedienungsanleitung

Argos

Argos Home Jenson Gloss Bedienungsanleitung

Argos

Argos Henley End Table 614/3150 Bedienungsanleitung

Argos

Argos Amelie 247/9873 Bedienungsanleitung

Argos

Argos Aspley 497/1379 Aspley 483/8209 Bedienungsanleitung

Argos

Argos SEAGRASS CHEST 424/3801 Bedienungsanleitung

Argos

Argos Hamlin 152/8062 Bedienungsanleitung

Argos

Argos Avebury 3ft Bed 355/2108 Bedienungsanleitung

Argos

Argos Foley 360/3679 Datenblatt

Argos

Argos 833/0325 Bedienungsanleitung

Argos

Argos Caspian 365/6499 Bedienungsanleitung

Argos

Argos SAVANNA 476/9086 Bedienungsanleitung

Argos

Argos 435/6152 Bedienungsanleitung

Argos

Argos Triple Metal And Polycotton Wardrobe Datenblatt

Argos

Argos 600/0774 Bedienungsanleitung

Argos

Argos JENSON 891/7944 Bedienungsanleitung

Argos

Argos 618/2915 Bedienungsanleitung

Argos

Argos Fabric Ottoman With 2 Small Stools 755/2238 Bedienungsanleitung

Argos

Argos Arizona 461/6366 Bedienungsanleitung

Argos

Argos Iceland 276107 Bedienungsanleitung

Argos

Argos Camden 259/4947 Bedienungsanleitung

Argos

Argos Aspley 391/8168 Bedienungsanleitung

Argos

Argos Aston Chair Bedienungsanleitung

Argos

Argos Sparkle Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung