Argos Camden 259/4947 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 80cm

Depth - 39cm

Height - 101.5cm

Camden - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 25/03/14

Important - Please read these instructions fully before starting assembly

Ruler - Use this ruler to help correctly identify the screws

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

249/7893

259/4947

ALR2986

Issue 2 - 26/02/13 - F code for the handle changed to F227.

Issue 3 - 12/12/13 - Extra Cat code added.

Issue 4 - 25/03/14 - Drawer depth increased. Old cat codes removed and new added.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 34kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 1, 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: If there is any

chance of this unit being pulled

over by children etc. it is

recommended that the unit is

secured to a wall using suitable

fixings (not supplied).

• Dispose of all packaging

carefully and responsibly.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Tools required

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Electric drill

(only use when

drilling into walls)

Components - Panels

Please check you have all the panels listed below

Drawer Divider - D0034A

145 x 249mm

1 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

80%

Drawer Base (T683-347)

(683 x 347mm) x 5

Drawer Back (W672-124)

(672 x 124mm) x 5 Back (X943)

(932 x 740mm)

Plinth (D1994A)

(722 x 96mm) x 2

Left Side (D1992A)

(979 x 389mm)

Top (D1991A)

(796 x 391mm)

Drawer Front (D1995A)

(716 x 173mm) x 5

Right Side (D1993A)

(979 x 389mm)

Left Drawer Side (W350-124LH)

(350 x 124mm) x 5

Right Drawer Side (W350-124RH)

(350 x 124mm) x 5

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 4

Metal dowel (F901) x 14

Large locking

nut (F900) x 4

Small locking

nut (F3) x 10

Small metal dowel (F893) x 4

19mm Screw (F461) x 10

Nail (F51) x 23

J K

Hollow core

locking nut

(F892) x 4

Bracket (F327) x 1

Wedgefix (F639) x 20

Knock-in Peg (F171) x 20

13mm Screw (F63) x 30 13mm Screw (F52) x 30

13mm Screw (F79) x 1

PR Runner (F160) x 5

L Runner (F161) x 5

L Runner (F159) x 5

R Runner (F162) x 5

Handle (F227) x 5

624mm

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the 5 drawer

fronts

Screw 2 metal dowels

into the holes shown on

the back of each drawer

front .

Note: Tighten metal

dowels up fully against

the panels.

Prepare drawer sides

and drawer backs

Insert a small locking

nut into the hole

shown on the left drawer

side and right drawer

side .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Step 2

80%

x 5

Step 3

Attach the drawer

sides to the drawer

front

Push the left drawer side

. and right drawer side

. onto the back of the

drawer front .

Turn the small locking

nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

Groove

Note: The locking nuts can be on either surface of the drawer sides.

Make sure that the small groove is on the inside, as shown.

x 5

Note: Due to the manufacturing process, the holes for the

locking nut can be on either surface of the drawer sides.

x 5 x 5

x 5

13 8

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 4

Step 5

Fit the drawer base

Slide the drawer base

down the grooves in the

drawer sides and

and down into the

groove in the drawer

front .

7 8

Attach the handles

Attach a handle to

each drawer front

using 2 screws .

Step 6

Fit the drawer back

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

7 8

x 5

Assembly Instructions

Step 7

80%

Step 8

Fit runners to the

drawers

Fit the runner to the

bottom edge of the left

drawer side , as

shown, making sure that

it is pushed up against

the back of the drawer

front . Use a bradawl

to mark the fixing

positions, then secure

with 2 screws .

Fit the runner to the

bottom edge of the right

drawer side using the

same method.

P c

P d

Fit the wedgefixes

Turn the drawer

assemblies over and fit

4 wedgefixes .

Slide 2 wedgefixes

into the small groove

located on the back of

the drawer front and

2 wedgefixes into the

small groove in the

drawer back .

Once in place, tighten up

the screws in the

wedgefixes .

x 5

Runners must be

pushed up against

the drawer front

P d

P c

x 5

Assembly Instructions

Step 9

80% Prepare the left side

a: Fit the 5 runners

to the left side .

The 1st screw uses

the 2nd hole in from the

front of the runner .

The 2nd and 3rd screw

use the holes that line up

with the other panel

holes.

b: Fit a screw into

the 2nd hole in at the top

of the runners .

c: Push 2 hollow core

locking nuts into the

left side , making sure

that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

Screw 2 metal dowels

into the holes on the left

side .

Note: Tighten metal

dowels up fully against

P a

Finished front edge

1st

screw

2nd

screw

3rd

screw

Prepare the left side

Fit the runner to the

left side .

The 1st screw uses

the 2nd hole in from the

front of the runner .

The 2nd screw uses

the hole that lines up

with the other panel hole.

Insert 2 large locking

nuts into the left side

. .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

L a

P a

Finished front edge

P a

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 10

Prepare the right side

a: Fit the 5 runners

to the right side .

The 1st screw uses

the 2nd hole in from the

front of the runner .

The 2nd and 3rd screw

use the holes that line up

with the other panel

holes.

b: Fit a screw into

the 2nd hole at the top of

the runners .

c: Push 2 hollow core

locking nuts into the

right side , making

sure that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

Screw 2 metal dowels

into the holes on the

right side .

Note: Tighten metal

dowels up fully against

the panel.

P b

Finished front edge

K1st

screw

2nd

screw

K3rd

screw

P b

Finished front edge

P b

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 11

Step 12

Fit the top

Attach the top onto

the right side .

Note: You will need to

slide the 2 small metal

dowels into the top

of the 2 hollow core

locking nuts .

Insert a screwdriver into

the 2 hollow core locking

nuts and turn the nuts

inside as far as they will

go.

C C

Prepare the top

Screw 4 small metal

dowels into the holes

on the top .

Note: Tighten metal

dowels up fully against

the panels.

Fix the bracket flush

to the front edge of the

groove in the top ,

398mm in from the side,

using screw .

398mm

Finished

front edge

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Napoli 600/6266 Bedienungsanleitung

Argos

Argos Merrick 227/3031 Bedienungsanleitung

Argos

Argos 600/6486 Bedienungsanleitung

Argos

Argos Jenson Mirror Bedienungsanleitung

Argos

Argos Malibu Tall Unit 833/7115 Bedienungsanleitung

Argos

Argos 618/2915 Bedienungsanleitung

Argos

Argos 709/2592 Bedienungsanleitung

Argos

Argos Eden 412/3062 Bedienungsanleitung

Argos

Argos Jenson 876/9109 Bedienungsanleitung

Argos

Argos Malibu 2 Drawer 3 Door Robe 257/6109 Bedienungsanleitung

Argos

Argos 240/9922 Bedienungsanleitung

Argos

Argos Alicia 171/5875 Bedienungsanleitung

Argos

Argos Home 603/4135 Bedienungsanleitung

Argos

Argos Home 615/1795 Bedienungsanleitung

Argos

Argos Flexa 3395884 Bedienungsanleitung

Argos

Argos Aurelie 557/4861 Datenblatt

Argos

Argos Hygena Bedienungsanleitung

Argos

Argos Ashley Dolls House Bookcase Bedienungsanleitung

Argos

Argos 795/9013 Bedienungsanleitung

Argos

Argos Swanley 120 307/0013 Bedienungsanleitung

Argos

Argos Islington Installationsanleitung

Argos

Argos PHOENIX 425/7079 Bedienungsanleitung

Argos

Argos Carly Desk 617-2592 Bedienungsanleitung

Argos

Argos Merrick 184/6335 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung