Argos Capella Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 78cm

Depth - 49cm

Height - 181cm

Capella - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 4 - 15/01/15

Important - Please read these instructions fully before starting assembly

267/9965

259/9760

228/5964

615/6154

ALR2990

257/7548

Issue 2 - 16/05/12 - New Code added

Issue 3 - 26/03/14 - Add 4 Plastinails. Remove old cat codes and add new ones.

Issue 4 - 15/01/15 - Over Balance Bracket replaced with Strap Kit.

Helpline number updated.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 44kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

overbalance protector kit

supplied or, an alternative fixing

method of your choice.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

80%

x 2

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Top/Base (D1015A)

(747 x 471mm) x 2

Door (D1017A)

(1701 x 369mm) x 2

Back (X829A)

(1711 x 773mm)

Plinth (D1016A)

(747 x 85mm)

Left Side (D1013A)

(1808 x 490mm)

Right Side (D1014A)

(1808 x 490mm)

Hanging Rail (FHR737)

(737mm long)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 10

Metal dowel (F901) x 10

D E

Large locking

nut (F900) x 10

G H

Nail (F51) x 34

see malibu fitment mk2 for large number of panels and fittings

Rail holder

(F1014) x 2

Handle (F930) x 2

25mm Screw (F50) x 4

Hinge (F522) x 6

Hinge plate

(F523) x 6

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step

ladder

Ruler - Use this ruler to help correctly identify the screws

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

13mm Screw (F63) x 12

Plastic Nail (F91) x 4

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Profiled

front edge

Profiled

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the left side

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Screw 5 metal dowels

into the left side .

Note: Tighten the metal

dowels up fully against

the panels.

Push a rail holder into

the left side . Make

sure that it is fitted

straight, in line with the

panel edges.

Prepare the right side

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Screw 5 metal dowels

into the right side .

Note: Tighten the metal

dowels up fully against

the panels.

Push a rail holder into

the right side . Make

sure that it is fitted

straight, in line with the

panel edges.

Profiled

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 3

Step 4

Prepare the top and

base

Tap 4 wooden dowels

into the top and base

. as shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Insert 4 large locking

nuts into the top

and base as shown.

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

10mm

Finished

front edge

Fit the top and base

to the right side

Push the top and

base onto the right

side as shown.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the top and base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

3 3

x 2

Important: If one of the top/base

panels has a plain chipboard surface

this must be used as the base.

Important: If one of the top/base

panels has a plain chipboard surface

this must be used as the base.

Profiled

front edge

Assembly Instructions

Step 5

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth

Note: Support the plinth

until the left side has been

fitted in the next step.

Step 6

Fit the plinth

Push the plinth onto

the right side as

shown.

Use a screwdriver to

tighten the large locking

nut fitted to the plinth

. .

Step 7

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the top , base and

plinth .

3 3

Plain chipboard

surface

Assembly Instructions

Step 8

Fit the back

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the

outside edges of the

back .

Note: Nails should

be spaced about 150mm

apart.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Warning: The

unit is heavy.

Lift with care.

Step 9

Fit the 4 plastic nails

Tap 2 plastic nails

into the bottom edge of

each of the sides and

. .

Stand the unit up

for the next step.

Assembly Instructions

Step 10

Fit the hanging rail

Push the hanging rail

into the rail holders

fitted to the side panels.

Step 11

Prepare the doors

Push fit 3 hinges into

each door .

Secure each hinge with

2 screws .

Note: Before securing

with the screws, make

sure that the hinges are

positioned at 90 degrees

with the edge of the

door.

x 2

Assembly Instructions

Step 12

Step 9

Fit the top and base

to the right side

Push the top and

base onto the right

side as shown.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the top and base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Fit doors and handles

Note: The easiest way to

attach each door is

to fit the top hinge first,

then align and fit the

other hinges.

a: Push the hinge

onto the front part of the

hinge plate .

The recess at the bottom

of screw B goes into the

slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge

plate as you slide it

across as far as it will go.

Tighten screw A.

c: The hinge must be

flat against the hinge

plate prior to any

adjustment.

d: The hinge must

NOT be AT AN ANGLE

to the hinge plate

when assembled.

This would indicate that

the recess at the bottom

of screw B had not

located in the slot in the

hinge plate and the hinge

would not be secure.

Remove the hinge from

the hinge plate and then

re-assemble being

careful to follow

instructions a-c.

e: Attach a handle to

each door using 2

screws .

a: b:

c: d:

Andere Handbücher für Capella

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Malibu 238/7154 Bedienungsanleitung

Argos

Argos Normandy 2 Door Tall Robe 357/1505 Bedienungsanleitung

Argos

Argos 356/3018 Bedienungsanleitung

Argos

Argos Heart of House kent 3 door 3 drawer wardrobe... Bedienungsanleitung

Argos

Argos Sywell 615/8482 Bedienungsanleitung

Argos

Argos 832/8076 Bedienungsanleitung

Argos

Argos St-Oil Bedienungsanleitung

Argos

Argos avignon 544/2687 Bedienungsanleitung

Argos

Argos 389/6400 Bedienungsanleitung

Argos

Argos Jenson 937/8032 Bedienungsanleitung

Argos

Argos Wow Lima 600/6503 Bedienungsanleitung

Argos

Argos Melamine 633/1591 Bedienungsanleitung

Argos

Argos Antonio 157-7563 Bedienungsanleitung

Argos

Argos Brixham 617/9131 Bedienungsanleitung

Argos

Argos Osaka 2556868 Bedienungsanleitung

Argos

Argos JENSON 891/7944 Bedienungsanleitung

Argos

Argos Malvern 395/5152 Bedienungsanleitung

Argos

Argos 322/8645 Bedienungsanleitung

Argos

Argos Verona Beech Bedienungsanleitung

Argos

Argos Barcelona 6545442 Bedienungsanleitung

Argos

Argos 2FT6 Josie Shorty Bunk Bed 436/6733 Bedienungsanleitung

Argos

Argos 603/3796 Bedienungsanleitung

Argos

Argos Islington Installationsanleitung

Argos

Argos Stroud scroll back pair chair 549/5737 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung