Argos Cheval 146/7965 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 69cm

Depth - 49.5cm

Height - 200cm

Cheval - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 10/01/14

Important - Please read these instructions fully before starting assembly

ALR2962

146/7965

147/4068

152/7324

146/8548

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 44.5kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

1 2

80%

x 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

3Top (D2721A)

(690 x 494mm)

Horizontal (D2722A)

(654 x 456mm) x 2

Door (D2725A)

(1888 x 337mm) x 2

Back (X1890-674)

(1890 x 674mm)

Plinth (D2723A)

(654 x 86mm)

Hanging Rail (FHR646)

(646mm long)

Right Side (D2719A)

(1981 x 458mm)

Left Side (D2720A)

(1981 x 458mm)

Rail (D2724A)

(654 x 86mm) x 2

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 18

Metal dowel (F901) x 14

D E

Large locking

nut (F900) x 14

G H I

Nail (F51) x 35

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

see malibu fitment mk2 for large number of panels and fittings

Rail Holder

(F891) x 2

19mm Screw (F461) x 4

13mm Screw (F63) x 1613mm Screw (F79) x 1

Bracket (F327) x 1

Handle (F274) x 2

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

40mm Screw (F910) x 4

Hinge (F518) x 6

Hinge plate

(F523) x 6

Plastic Nail (F91) x 4

Finished

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the left side

Tap 2 wooden dowels

into the left side .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Screw 7 metal dowels

into the left side .

Note: Tighten the metal

dowels up fully against

the panels.

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Fit the rail holder to

the left side using 2

screws .

To fit the rail holder, screw

through its top hole and into the

shallow mark hole drilled in the

panel. Make sure that it is fitted

straight, in line with the panel

edges and then fit another

screw using the lower hole.

Prepare the right side

Tap 2 wooden dowels

into the right side .

Screw 7 metal dowels

into the right side .

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Fit the rail holder to

the right side using 2

screws .

10mm

Finished

front edge

Finished

front edge

Finished

top edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 3

Step 4

Finished

front edge A

Prepare the 2

horizontals

Tap 4 wooden dowels

into each horizontal .

Insert 4 large locking

nuts into each

horizontal .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Cx 2

Fit the 2 horizontals

to the right side

Push the 2 horizontals

onto the right side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted

each horizontal .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 5

Prepare the plinth and

the 2 rails

Tap 2 wooden dowels

into the plinth and

each of the 2 rails .

Insert 2 large locking

nuts into the plinth

and each of the 2 rails

. .

Note: The plinth and the

2 rails can have a plain

chipboard surface.

Note: The rails have a finished top edge.

Plain

chipboard

surface

x 2

Plain

chipboard

surface

Finished

front edge

Assembly Instructions

Step 6

Finished

top edge

Fit the plinth and rails

Push the plinth onto

the right side .

Use a screwdriver to

tighten the large locking

nut fitted to the plinth

. .

Push the 2 rails onto

the right side .

Use a screwdriver to

tighten the large locking

nuts fitted to the 2

rails .

Note: Support the plinth

and the rails until the left

side has been fitted in

the next step.

Step 7

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 7 large

locking nuts fitted to

the horizontals , the

plinth and the 2 rails

. .

Note: The 2 rails have

a finished top edge.

Finished

top edge

Assembly Instructions

Step 8

Step 9

Fit the top and the

plastic nails

Push the top onto

the assembly and secure

it to the sides and

using 4 screws .

Tap 2 plastic nails

into the bottom edge of

each of the sides and

. as shown.

1 2

Fit the back

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the back

onto the unit, making

sure it is pushed up

against the top .

Nail around the

outside edges of the

back .

Note: Nails should be

spaced about 150mm

apart.

Stand the unit up for

the next step.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Warning: The

unit is heavy.

Lift with care.

Finished

front edge

Assembly Instructions

Step 10

Step 11

Fit the hanging rail

Push the hanging rail

. into the rail holders

fitted to the side panels.

Prepare the 2 doors

Push fit 3 hinges into

each of the doors .

Secure each hinge with

2 screws .

Note: Before securing

with the screws, make

sure that the hinges are

positioned at 90 degrees

with the edge of the

door.

x 2

Assembly Instructions

Step 12

Fit doors and handles

Note: The easiest way to

attach each door is

to fit the top hinge first,

then align and fit the

other hinges.

a: Push the hinge

onto the front part of the

hinge plate .

The recess at the bottom

of screw B goes into the

slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge

plate as you slide it

across as far as it will go.

Tighten screw A.

c: The hinge must be

flat against the hinge

plate prior to any

adjustment.

d: The hinge must

NOT be AT AN ANGLE

to the hinge plate

when assembled.

This would indicate that

the recess at the bottom

of screw B had not

located in the slot in the

hinge plate and the hinge

would not be secure.

Remove the hinge from

the hinge plate and then

re-assemble being

careful to follow

instructions a-c.

e: Attach a handle to

each door using 2

screws .

a: b:

c: d:

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Atlas 157/3309 Bedienungsanleitung

Argos

Argos Mia 2627436 Bedienungsanleitung

Argos

Argos Aspley 481/9651 Bedienungsanleitung

Argos

Argos 06006170 Bedienungsanleitung

Argos

Argos PAULO LARGE RECLINER 1454026 Bedienungsanleitung

Argos

Argos 737/8876 Bedienungsanleitung

Argos

Argos SWIVEL Bedienungsanleitung

Argos

Argos Newport Bedienungsanleitung

Argos

Argos 832/7149 D Bedienungsanleitung

Argos

Argos Cheval 147/8985 Bedienungsanleitung

Argos

Argos 149113 Bedienungsanleitung

Argos

Argos Pacific 6 Seater Patio Set 651/1531 Bedienungsanleitung

Argos

Argos HOME 607/7446 Bedienungsanleitung

Argos

Argos 356/3018 Bedienungsanleitung

Argos

Argos Nordic 4x2 Drawer Chest Bedienungsanleitung

Argos

Argos Medium Pink Velvet Ottoman 419/8688 Bedienungsanleitung

Argos

Argos Victoriana 244/5034 Bedienungsanleitung

Argos

Argos 906/4638 Bedienungsanleitung

Argos

Argos 389/5690 Bedienungsanleitung

Argos

Argos SEAGRASS CHEST 424/3801 Bedienungsanleitung

Argos

Argos Verona 609/5026 Bedienungsanleitung

Argos

Argos Star 8053011 Bedienungsanleitung

Argos

Argos 9011179 Bedienungsanleitung

Argos

Argos Marcell 4ft6 Frame Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung