Argos Cheval 147/2204 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 103cm

Depth - 49.5cm

Height - 200cm

Cheval - 3 Door Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Important - Please read these instructions fully before starting assembly

ALR2966

147/2204

143/9388

146/7680

147/0361

Issue 2 - 08/09/14

Issue 2 - 08/09/14 - Round Back Holders have been changed to Oblong Back Holders.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 77kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 1, 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

Components - Panels

Please check you have all the panels listed below

80%

x 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1 2 3

12 13 14

Large Hanging Rail (FHR646)

(646mm long)

Small Hanging Rail (FHR317)

(317mm long) x 2

Left Side (D2720A)

(1981 x 458mm)

Right Side (D2726A)

(1981 x 458mm)

Large Horizontal (D2722A)

(654 x 456mm)

Plinth (D2729A)

(995 x 86mm)

Top (D2727A)

(1030 x 494mm)

Base (D2733A)

(995 x 456mm)

Upright (D2731A)

(1879 x 455mm)

Small Back (X1890-345)

(1890 x 345mm)

Large Back (X1890-674)

(1890 x 674mm)

Small Horizontal (D2732A)

(325 x 456mm)

Rail (D2724A)

(654 x 86mm) x 2

Mirror Door (D2725MA)

(1888 x 337mm) x 3

(Mirror - SG24

1817 x 260mm

Safety Back SAR)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 26

Metal dowel (F901) x 18

D E

Large locking

nut (F900) x 18

G H I

Nail (F51) x 39

Rail Holder

(F891) x 6

19mm Screw (F461) x 6

13mm Screw (F63) x 3013mm Screw (F79) x 1

Bracket (F327) x 1

Handle (F274) x 3

40mm Screw (F910) x 8

Hinge (F518) x 9

Hinge plate

(F523) x 9

Plastic Nail (F91) x 4

Nail screw (F277) x 5

Back holder (F276) x 5

*These can also be round

Finished

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the upright

a: Tap 4 wooden dowels

. into the upright .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Screw 2 metal dowels

into the upright .

Note: Tighten the metal

dowels up fully against

the panels.

Fit 2 rail holders to

the upright using 2

screws in each.

Turn the upright over

b: Screw 4 metal dowels

. into the upright .

Fit 3 hinge plates onto

the upright , making

sure that the slot is

facing towards the

finished front edge.

Fit a rail holder to the

upright using 2

screws .

To fit the rail holder, screw

through its top hole and into the

shallow mark hole drilled in the

panel. Make sure that it is fitted

straight, in line with the panel

edges and then fit another

screw using the lower hole.

a: 10mm

Turn the upright over

Finished

front edge

Finished

front edge

Assembly Instructions

Step 2

Step 4

Step 3

Fit the large

horizontal to the

upright

Push the large horizontal

. onto the upright .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the large horizontal .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

10 3

Finished

front edge A

Prepare the large

horizontal

Tap 4 wooden dowels

into the large horizontal

. .

Insert 4 large locking

nuts into the large

horizontal .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Finished

front edge

Prepare the small

horizontal

Tap 4 wooden dowels

into the small horizontal

. .

Insert 4 large locking

nuts into the small

horizontal .

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 5

Fit the small

horizontal to the

upright

Push the small horizontal

. onto the upright .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the small horizontal .

11 3

Finished

front edge

Step 6

Prepare the base

Tap 4 wooden dowels

into the base .

Insert 4 large locking

nuts into the base .

Step 7

Fit the base

Push the base onto

the upright and

secure with 2 screws .

plain chipboard surface

Note: The base

can have a plain

chipboard surface.

Assembly Instructions

Step 8

Step 9

Fit the right side

Push the right side

onto the base and

small horizontal .

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the small horizontal

and the base .

Prepare the right side

Tap 2 wooden dowels

into the right side .

Screw 5 metal dowels

into the right side .

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Fit 2 rail holders to

the right side using 2

screws .

Note: Use the shallow

mark holes to fit the top

screw in the rail holders

(refer back to Step 1).

Finished

front edge

Finished

front edge

Assembly Instructions

Step 10

Step 12

Finished

top edge

Step 11

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth .

Prepare the left side

Tap 2 wooden dowels

into the left side .

Screw 7 metal dowels

into the left side .

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Fit a rail holder to the

left side using 2

screws .

Prepare the 2 rails

Tap 2 wooden dowels

into each of the rails .

Insert 2 large locking

nuts into each of the

rails .

10mm

Plain

chipboard

surface

x 2

Plain

chipboard

surface

Note: The plinth

can have a plain

chipboard surface.

Note: The 2 rails

can have a plain

chipboard surface.

Finished

front edge

Assembly Instructions

Step 13

Finished

top edge

Fit the plinth and rails

Push the plinth onto

the right side .

Use a screwdriver to

tighten the large locking

nut fitted to the plinth

. .

Push the rails onto

the upright .

Use a screwdriver to

tighten the large locking

nut fitted to the 2

rails .

Note: Support the

plinth and rails until

the left side has been

fitted in the next step.

Step 14

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 7 large

locking nuts fitted to

the base , plinth , 2

rails and large

horizontal .

5 6

Finished

top edge

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Normandy Bedienungsanleitung

Argos

Argos Modular Bedienungsanleitung

Argos

Argos Islington Installationsanleitung

Argos

Argos MADRID SPRING CUSHION CHAIR 6187862 Bedienungsanleitung

Argos

Argos SAN DIEGO 408/8365 Bedienungsanleitung

Argos

Argos Under Basin Unit 833/2763 Bedienungsanleitung

Argos

Argos 833 /3559 Bedienungsanleitung

Argos

Argos Stakka 632/0973 Bedienungsanleitung

Argos

Argos 601/5130 Bedienungsanleitung

Argos

Argos 617/1799 Bedienungsanleitung

Argos

Argos Atlas 161/5803 Bedienungsanleitung

Argos

Argos Tolga 483/8364 Bedienungsanleitung

Argos

Argos Denver 339/9622 Bedienungsanleitung

Argos

Argos Home New Pagnell 601/9435 Bedienungsanleitung

Argos

Argos Arizona 541/9517 Bedienungsanleitung

Argos

Argos Boston 609/0052 Bedienungsanleitung

Argos

Argos 609/7024 Bedienungsanleitung

Argos

Argos Malvern 395/6632 Bedienungsanleitung

Argos

Argos OXFORD DINING FURNITURE Produktinformationsblatt

Argos

Argos 619/1834 Bedienungsanleitung

Argos

Argos AH TOBY 8545550 Bedienungsanleitung

Argos

Argos Jonas 887/3710 Bedienungsanleitung

Argos

Argos 609/2263 Bedienungsanleitung

Argos

Argos HOME Doublebed White 4Ft Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung