Argos Hallingford Gloss 790/7711 Bedienungsanleitung

MADE IN

BRITAIN

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk

or email: [email protected]o.uk (quoting your original order number)

Alternatively, call the Spares Helpline on: 0330 016 1114

For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assem-

Assembly Instructions - Important: Retain these instructions for

future reference

More help is available throughout this

booklet by scanning in the QR codes or

typing in the links

WARNING!

In order to prevent overturning, this product must be used

with the wall attachment device provided

Dimensions

Width - 37.5cm

Depth - 39.6cm

Height - 58cm

Hallingford Gloss - 3 Drawer Bedside

Issue 5 - 11/08/20

790/7711

760/8632

814/5091

806/8721

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• Regularly check all fastenings

to ensure that they are properly

tightened.

• Warning: This unit weighs

approximately 14kgs.

Please lift with care.

• Assembly to be carried out by

a competent adult only.

• Check you have all the

components and tools listed on

pages 1, 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• During assembly children

should be kept away from the

product due to possible risk of

injury.

• Installation shall only be

carried out exactly according to

the manufacturer’s instructions

- otherwise a safety risk can

occur if incorrectly installed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• WARNING: To prevent

possible overbalancing this unit

must be secured to a wall

using the overbalance

protector kit supplied.

• Dispose of all packaging

carefully and responsibly.

• Do not use this item if any

components are missing or

damaged.

Tools required

Rule

Scissors

Hammer

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Electric drill

(do not use for

fitting screws)

Bradawl

Flat-head

screwdriver

Spirit level

Components - Panels

Please check you have all the panels listed below

6 7

Left Side (DF-00010160)

(55.6 x 37.2cm)

Right Side (DF-00010161)

(55.6 x 37.2cm)

Top (DF-00010162)

(37.5 x 39.6cm)

1Drawer Front (DF-00010163)

(36 x 16.2cm) x 3

2Left Drawer Side (WRP-00000156)

(35 x 13cm) x 3

3Right Drawer Side (WRP-00000157)

(35 x 13cm) x 3

4Drawer Base (TDF-00022245)

(31.95 x 34.7cm) x 3

5Drawer Back (WRP-00000463)

(30.85 x 13cm) x 3

9Plinth (DF-00018114)

(34.1 x 6cm) x 2

10 Back (X535-366)

(53.5 x 36.6cm)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Components - Fittings

Main Fittings Bag

Individual Fittings Bags

Drawer Fittings Bag marked ‘drw kit’

A C

Knock-in Peg (F171GY) x 12

D E

19mm Screw (F461) x 6

Small locking cam

nut (F3) x 6

Metal dowel (F901) x 6

Wedgefix (F639) x 6

Drawer runner (F450) x 6

Handle (F306) x 3

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

9mm Screw (F74) x 6

Plastic Nail (F91) x 4

9mm Screw (F73) x 12

Wooden dowel (F22) x 8

Nail (F51) x 20

Metal dowel (F901) x 8

Large locking cam nut (F900) x 8

Overbalance protector kit (F474) x 1

Assembly Instructions

Step 1

x 3

x 3 x 3

Step 2

Prepare the 3 drawer

fronts

Screw 2 metal dowels

into each of the 3 drawer

fronts .

Note: Tighten the metal

dowels up fully against

the panels.

Prepare the 3 sets of

drawer sides

Insert a small locking

cam nut into the left

drawer sides and

right drawer sides .

Note: The arrow on the

locking cam nut must

point towards the hole in

the edge of the panel.

Step 3

Attach the drawer

sides to the drawer

fronts

Push the left drawer side

. and right drawer side

. onto the back of the

drawer front .

Turn the small locking

cam nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

cam nuts clockwise

to secure panels - more

than 1/2 a turn.

www.youtube.com/watch?v=InNBV_uuMmo

Drawer Assembly

Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7

Assembly Instructions

Step 4

Fit the drawer bases

Slide the drawer base

down the grooves in the

drawer sides and

and down into the

groove in the drawer

front .

Step 5

Fit the drawer backs

Fit the drawer back

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

2 3

Step 7

2 3

103

Step 6

Fit the handles

Attach a handle to

each drawer front

using screws .

Fit the wedgefixes

Turn the 3 drawer

assemblies over and

slide 2 wedgefixes

into the front and back

grooves, as shown, and

tighten up the screws.

Important: Make sure

that the drawer assembly

is square before fitting

the wedgefixes.

x 3

Finished

front edge

Finished

front edge H

Assembly Instructions

Step 8

Prepare the left side

a: Place 3 runners on

the left side as

shown. Slide back the

top of runner and use the

2nd hole from the front

to fit the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the left side .

c: Screw 2 metal

dowels into the left

side .

Insert 2 large locking

nuts into the left side

. .

Note: The arrow on the

locking nuts must point

towards the hole in the

edge of the panel.

Tap 2 wooden dowels

into the left side .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Finished

front edge

www.youtube.com/watch?v=yG4xJJeSg

Fitting Ball Bearing Runners

10mm

Finished

front edge

Assembly Instructions

Step 9

Prepare the right side

a: Place 3 runners on

the right side as

shown. Slide back the

top of runner and use the

2nd hole from the front

to fit the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the right side .

c: Screw 2 metal

dowels into the right

side .

Insert 2 large locking

nuts into the right

side .

Tap 2 wooden dowels

into the right side .

Finished

front edge

Prepare the 2 plinths

Insert 2 large locking

nuts into each of the

2 plinths .

Tap 2 wooden dowels

into each of the 2 plinths

. . H

Step 10

x 2

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 11

Join the 2 plinths to

the right side

Push the 2 plinths

onto the right side .

Use a screwdriver to

tighten the 2 large

locking cam nuts

fitted to the plinths .

Note: Turn the large

locking cam nuts as

far as they will go - more

than 1/2 a turn.

Note: Support this

plinth until the left

side has been fitted

in the next step

Fit the left side

Push the left side

onto the 2 plinths .

Use a screwdriver to

tighten the 2 large

locking cam nuts

fitted to the plinths .

Step 12

Prepare the top

Screw 4 metal dowels

into the top .

Fit the bracket from the

overbalance protector kit

. to the shallow

mark-hole drilled into

the top using 1 of its

screws.

Note: Only fit 1 of the

screws, the other 1 will

be fitted later.

Step 13

Finished

front edge

Finished

front edge

Assembly Instructions

Step 14

Fit the top

Note: To make it easier

to fit the top, place

polystyrene blocks from

the packaging

underneath the side

panels to raise the

assembly.

Push the top onto

the assembly.

Use a screwdriver to

tighten the 4 large

locking cam nuts

fitted to the sides

and .

Fit the back

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the

outside edges of the

back .

Note: Nails should be

spaced about 150mm

apart.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

www.youtube.com/watch?v=FeaI6541z7o

Squaring up a Chest and tting the Back Panel

Step 15

Polystyrene

block

Polystyrene

block

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Henley 428/0369 Bedienungsanleitung

Argos

Argos Hygena Charlie 323/2349 Bedienungsanleitung

Argos

Argos Gabe Bedienungsanleitung

Argos

Argos 2 Door Media Unit/Low Sideboard 482/0437 Bedienungsanleitung

Argos

Argos Napoli 600/6273 Bedienungsanleitung

Argos

Argos KINGSTON 6029731 Bedienungsanleitung

Argos

Argos Rattan 3566651 Bedienungsanleitung

Argos

Argos Beech Effect TV Bench 609/0162 Bedienungsanleitung

Argos

Argos Scandinavia Bedienungsanleitung

Argos

Argos 357/7097 Bedienungsanleitung

Argos

Argos Iceland 276107 Bedienungsanleitung

Argos

Argos Arizona 541/9517 Bedienungsanleitung

Argos

Argos Valencia 633/7777 Bedienungsanleitung

Argos

Argos Home Baltimore 855/4819 Bedienungsanleitung

Argos

Argos Merrick 184/6335 Bedienungsanleitung

Argos

Argos 144/3556 Bedienungsanleitung

Argos

Argos Alfie Bedienungsanleitung

Argos

Argos Jenson 930/7450 Bedienungsanleitung

Argos

Argos 737/6672 Handbuch

Argos

Argos 2667537 Bedienungsanleitung

Argos

Argos 484/2831 Bedienungsanleitung

Argos

Argos WOW 152/7252 Datenblatt

Argos

Argos Aruba 617/2602 Bedienungsanleitung

Argos

Argos Iceland 279721 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung