Argos Malibu Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 195cm

Depth - 95cm

Height - 53cm

Malibu - Cabin Bed

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 08/07/14

Important - Please read these instructions fully before starting assembly

ALR3047

268/5038

278/5433

275/7557

249/2032

280/3315

275/4433

WARNING

NOT SUITABLE FOR CHILREN

UNDER 4 YEARS OF AGE .

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 66kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: If there is any

chance of this unit being pulled

over by children etc. it is

recommended that the unit is

secured to a wall using suitable

fixings (not supplied).

• Dispose of all packaging

carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Tools required

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

IMPORTANT

On a regular basis please

check that the screws and

fittings have not become

loose as this could present

a potential choke hazard.

Components - Panels

Please check you have all the panels listed below

80%

x 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Back Rail (D2926A)

(1920 x 160mm)

Back (D2927A)

(820 x 367mm)

Horizontal (D2932A)

(820 x 287mm)

Base (D2928A)

(1920 x 455.5mm) x 2

Left Upright (D2937A)

(367 x 660mm)

Left End (D2931A)

(949 x 529mm)

Right Upright (D2929A)

(367 x 660mm)

Middle Plinth (D2933A)

(820 x 60mm)

Right End (D2936A)

(949 x 529mm)

Left Plinth (D2934A)

(535 x 60mm) x 2

Right Plinth (D2935A)

(535 x 60mm) x 2

Front Rail (D2938A)

(1920 x 160mm)

Support Rail (D2939A)

(1920 x 92mm) x 2

Drawer front (D2930A)

(531 x 149mm) x 4

Drawer Back (W502-124)

(502 x 124mm) x 4

Left Drawer Side (W370-124LH)

(370 x 124mm) x 4

Drawer Base (T513-367)

(513 x 367mm) x 4

Right Drawer Side (W370-124RH)

(370 x 124mm) x 4

18 Shelf (D3030A)

(820 x 287mm)

Please check you have all the fittings listed below

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

Wooden dowel (F22) x 16

Metal dowel (F901) x 10

Large locking

nut (F900) x 6

Small locking

nut (F3) x 8

G H I

25mm Screw (F50) x 4

Handle (F631) x 4

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

45mm Screw (F65) x 10

Wedgefix (F639) x 8

Knock-in Peg (F171GY) x 16

Drawer runner (F1004) x 8

Plastic Nail (F91) x 10

Large wooden dowel (F40) x 2

Double metal dowel (F566) x 2

Allen Key (F36) x 1

50mm Screw (F49) x 48

13mm Screw (F79) x 5

9mm Screw (F74) x 8

9mm Screw (F73) x 16

13mm Screw (F52) x 5

Bracket (F327) x 5

Shelf stud (F372) x 4

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 4

x 4x 4

x 4

Step 2

Prepare the 4 drawer

fronts

Screw 2 metal dowels

into each of the 4 drawer

fronts .

Note: Tighten the metal

dowels up fully against

the panels.

Prepare 4 pairs of

drawer sides

Insert a small locking

nut into the hole

shown on the left drawer

side and the right

drawer side .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Step 3

Attach the drawer

sides to the drawer

fronts

Push the left drawer sides

. and right drawer sides

. onto the back of the

4 drawer fronts .

Turn the small locking

nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

15 16

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base

down the grooves in the

drawer sides and

and down into the

groove in the drawer

front .

Step 5

Fit the drawer back

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

Step 6

15 16

Attach the handles

Attach a handle to

each of the drawer fronts

. using screw .

Note: Do not

overtighten the screw.

x 4

15 16

x 4

Step 7

Fit the wedgefixes

Turn the drawer

assemblies over and

slide 2 wedgefixes

into the front and back

grooves, as shown, and

tighten up the screws.

Finished

front edge A

Assembly Instructions

Step 8

Step 9

Finished

front edge

Prepare the left

upright

a: Tap 2 wooden dowels

. into the left upright .

Screw a metal dowel

into the left upright .

Place 2 runners on

the left upright as

shown. Slide back the

top of runner and use the

2nd hole from the front

to fit the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the left upright .

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Prepare the right

upright

a: Tap 2 wooden dowels

. into the right upright

. .

Screw a metal dowel

into the right upright .

Place 2 runners on

the right upright as

shown. Slide back the

top of runner and use the

2nd hole from the front

to fit the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the right upright .

Finished

front edge

Finished

front edge

Assembly Instructions

Step 10

Fit the horizontal to

the right upright

Fit the horizontal

onto the right upright

using 2 screws and

the allen key .

Plain chipboard

surface

Step 11

Prepare the middle

plinth

Insert 2 large locking

nuts into the middle

plinth .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Step 12

Fit the middle plinth

a: Tap a double metal

dowel and a large

wooden dowel through

the right upright and

into the middle plinth

until they ‘’bottom out’’.

b: Use a screwdriver to

tighten the large locking

nut fitted to the

middle plinth .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Secure the other right

plinth

a: Tap a double metal

dowel through the

right plinth at the

front of the assembly

and into the right upright

until it ‘’bottoms out’’.

b: Use a screwdriver to

tighten the large locking

nut fitted to the right

plinth .

Important: It is critical

that the middle plinth is

asssembled with the large

locking nuts at the top.

Finished

front edge

Assembly Instructions

Step 13

Step 14

Finished

front edge

Secure the other right

plinth

a: Tap a double metal

dowel through the

right plinth at the

front of the assembly

and into the right upright

until it ‘’bottoms out’’.

b: Use a screwdriver to

tighten the large locking

nut fitted to the right

plinth .

Fit the right upright

Push the right upright

onto the 2 right plinths

. .

Use a screwdriver to

tighten the large locking

nut fitted to the right

plinth at the back of

the assembly.

Note: Turn the large

locking nut as far as it

will go - more than 1/2 a

turn.

Finished

front edge

Step 2

Step 15

Prepare the back

Tap 2 wooden dowels

into the back .

Plain chipboard

surface

Fit the back

Push the back onto

the right upright and

fix it using 2 screws

and the allen key .

Fit the left upright

Push the left upright

onto the assembly and

fix it using 4 screws

and the allen key .

Plain chipboard

surface

Finished

top edge

Finished

top edge

Assembly Instructions

Step 16

Step 17

Plain

chipboard

surface

Fit the middle plinth

Push the middle plinth

onto the right upright

. .

Use a screwdriver to

tighten the large locking

nut fitted to the

middle plinth .

Fit the back

Push the back onto

the right upright and

secure it using 2 screws

. and the allen key .

Step 7

Secure the middle

plinth to the left

upright

a: Tap a double metal

dowel and a large

wooden dowel

through the left upright

and into the middle

plinth until they

‘’bottom out’’.

b: Use a screwdriver to

tighten the large locking

nut fitted to the

middle plinth .

Step 18

Prepare the 2 left

plinths

Tap a wooden dowel

into just 1 of the 2 left

plinths .

Insert a large locking

nut into each of the 2

left plinths .

Plain chipboard

surface

Plain chipboard

surface

Rear Front

Fit the 4 plastic nails

Tap 2 plastic nails

into the bottom edge of

each of the uprights

and . .

Carefully stand the

assembly up.

Andere Handbücher für Malibu

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Stirling Bedienungsanleitung

Argos

Argos HOME Maine 2 Door 1 Drawer Sideboard Bedienungsanleitung

Argos

Argos Aubrey 549/6516 Bedienungsanleitung

Argos

Argos Vancouver II 643/8133 Bedienungsanleitung

Argos

Argos PAULO LARGE RECLINER 1454026 Bedienungsanleitung

Argos

Argos Corners 9583119 Bedienungsanleitung

Argos

Argos Habitat 600/5779 Bedienungsanleitung

Argos

Argos HOME LARGE TRESTLE TABLE DESK Bedienungsanleitung

Argos

Argos 435/6152 Bedienungsanleitung

Argos

Argos Landon 241/7990 Bedienungsanleitung

Argos

Argos Tolga-22R Bedienungsanleitung

Argos

Argos 906/4009 Bedienungsanleitung

Argos

Argos 833 /3559 Bedienungsanleitung

Argos

Argos Canterbury 3 DR Robe Bedienungsanleitung

Argos

Argos Princess Dining Chair 398/1298 Bedienungsanleitung

Argos

Argos Jenson 937/4610 Bedienungsanleitung

Argos

Argos Foley 360/3679 Datenblatt

Argos

Argos Modular Bedienungsanleitung

Argos

Argos Darcy 428/5890 Bedienungsanleitung

Argos

Argos 709/2592 Bedienungsanleitung

Argos

Argos Fuji 8 607/2960 Bedienungsanleitung

Argos

Argos Emberton 927/5788 Bedienungsanleitung

Argos

Argos Gloucester 609/1233 Bedienungsanleitung

Argos

Argos Cheval 152/6882 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung