Argos Malibu Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 74.5cm

Depth - 50cm

Height - 181cm

Malibu - 3 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference 630/2685

630/3158

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 11/10/13

Important - Please read these instructions fully before starting assembly

Ruler - Use this ruler to help correctly identify the screws

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

ALR2425

630/2427

630/2702

630/2661

Issue 2 - 17/09/12 - Added notes to drawer wrap preparation stages telling customer the cams can be either surface of the wrap

194/5999

189/7047

181/9551

192/6523

191/2180

147/2668

Issue 3 - 11/10/13 - 6 new codes added to front page.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 49kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Plinth - D0118A

714 x 92mm

Rail - D0119A

714 x 66mm

Back Rail - D0120A

714 x 60mm

Components - Panels

Please check you have all the panels listed below

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Left Side (D0124A)

(1808 x 496mm)

Drawer Divider - D0034A

145 x 249mm

waterfall

Drawer Wrap (W162) x 3

(1308 x 95mm)

Plinth (D0128A) x 2

(714 x 92mm)

70%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Right Side (D0125A)

(1808 x 496mm)

Drawer Front (D0131A) x 3

(710 x 157mm)

Base (D0126A)

(714 x 478mm)

Top (D0127A)

(714 x 494mm)

Drawer Base (T162) x 3

(299 x 695mm)

Hanging Rail (FHR704)

(704mm long)

Rail (D0129A)

(714 x 92mm)

Door (D0130A) x 2

(1199 x 353mm)

11 Foldy Back (XBO3379)

(1219 x 738mm)

Please check you have all the fittings listed below

Tools required

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 12

Metal dowel (F901) x 6

Nail holder (F149) x 1

D F

40mm Screw (F910) x 12

13mm Screw (F79) x 1

25mm Screw (F50) x 8 Handle (F631) x 8

Rule

ScissorsSquare

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Nail (F51) x 26

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M ON

P Q

Bracket (F327) x 1

R (F601)

L (F600)

F599

Drawer stops (F599) x 6

Runners (F600) x 3 and (F601) x 3

Electric drill

Step

ladder

Small locking

nut (F3) x 6

Rail holder

(F1014) x 2

13mm Screw (F63) x 10

19mm Connecting bolt

(F461) x 2

Hinge plate

(F523) x 4

Hinge (F522) x 4

25mm Connecting sleeve

(F432) x 2

Ruler - Use this ruler to help correctly identify the screws

Assembly Instructions

Prepare the 3 drawer

fronts and wraps

a: Screw 2 metal

dowels into the holes

on the back of the

drawer fronts .

Note: Tighten metal

dowels up fully against

the panels.

b: Insert 2 small locking

nuts into the holes

shown on the drawer

wrap .

Note: Arrow on locking

nut must point

towards hole in edge of

panel.

Assemble the drawers

a: Place the drawer

base into the narrow

slot on the drawer wrap

. . Fold wrap around

the base.

b: Turn drawer wrap

assembly over and push

onto the back of the

drawer front .

Turn locking nuts

clockwise to secure

panels - more than 1/2 a

turn.

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

80%

Step 1

Step 2

Note: Due to the manufacturing

process, the holes for the

locking nut can be on either

surface of the drawer sides.

Note: The locking nuts

can be on either surface

of the drawer sides.

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit the drawer stops

Carefully break off the 2

drawer stops (F599) from

each pair of the drawer

runners .

Push the drawer stops

fully through the drawer

wraps from the

inside.

Attach the handles

Attach a handle to

each drawer front

using screw .

Note: Do not

overtighten the screw.

SNAP!

F599

Step 4

Step 3

Assembly Instructions

Step 5

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 1

80% x 3

Prepare the left and

right side

Separate runners .

a: Push fit 3 left

runners marked ‘L’

into the holes shown on

left side .

Note: Runners must be

be fitted flat against the

panel. If necessary

gently tap into final

position.

Fit 2 hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

b: Push fit 3 right

runners marked ‘R’

into the holes shown on

right side .

Fit 2 hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Finished

front edge

Finished

front edge

F601

F600

Assembly Instructions

Step 6

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Prepare top and base

a: Tap 2 wooden

dowels into the ends

of the top .

b: Tap 2 wooden

dowels into the ends

of the base .

Fit the top and base

to the right side

Attach the top

to the right side

using the dowel

already fitted and

secure with 2

screws .

Attach the base

to the right side

using the dowel

already fitted and

secure with 2

screws .

Finished

front edge

Finished

front edge

Finished

front edge

plain chipboard surface

Step 7

plain chipboard surface

Finished

front edge

Assembly Instructions

Step 8

Prepare the 2 plinths

and the rail

a: Tap 2 wooden

dowels into the ends

of the 2 plinths .

b: Tap 4 wooden

dowels into the ends

of the rail .

Finished front edge

Fit the rail

Attach the rail to the

right side using the

dowels already fitted.

Step 9

Plain chipboard

surface

Plain chipboard

surface

Plain chipboard

surface

Assembly InstructionsAssembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

This outer face should

be the same colour as

the main unit panels

Back

of unit

Fit the 2 plinths

2 people are needed

here

Attach the 2

plinths to

the right side

using the dowel

already fitted to

them and

secure with

screws .

Note: Support

the plinth at the back

of the unit until the left

side has been fitted in

the next stage.

Fit the left side

Push the left side

onto the unit and secure

with 6 screws .

Step 10

Step 11

Support

this plinth

Andere Handbücher für Malibu

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Rattan 4 Piece Sofa Set 502/2636 Bedienungsanleitung

Argos

Argos Kensington Installationsanleitung

Argos

Argos Arizona 541/9517 Bedienungsanleitung

Argos

Argos PENTON 490/9475 Bedienungsanleitung

Argos

Argos 875/2886 Bedienungsanleitung

Argos

Argos 900/2566 Bedienungsanleitung

Argos

Argos PHOENIX 425/7079 Bedienungsanleitung

Argos

Argos San Diego 343/7058 Bedienungsanleitung

Argos

Argos Atlas 157/3309 Bedienungsanleitung

Argos

Argos Tammy 918-2723 Bedienungsanleitung

Argos

Argos 166/6890 Bedienungsanleitung

Argos

Argos Haversham Bedienungsanleitung

Argos

Argos 609/5741 Bedienungsanleitung

Argos

Argos Jarvia 143/6202 Bedienungsanleitung

Argos

Argos Chicago Dining Set Bench Bedienungsanleitung

Argos

Argos Franklin Recliner 2493567 Bedienungsanleitung

Argos

Argos 833/2811 Bedienungsanleitung

Argos

Argos 832/7149 D Bedienungsanleitung

Argos

Argos TOBY 8559230 Bedienungsanleitung

Argos

Argos Malibu 256/0029 Bedienungsanleitung

Argos

Argos Scandinavia 4 door robe w/ 2+4 drws. Bedienungsanleitung

Argos

Argos ASTON 152/5546 Bedienungsanleitung

Argos

Argos Atlantic 759/0692 Bedienungsanleitung

Argos

Argos Cheval 147/2204 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung